Download  Print this page

Tekkeon myTalker ET7000 User Manual

Bluetooth gateway for ipod and mp3 players
Hide thumbs

Advertisement

ET7000
User Guide
Bluetooth Gateway for
iPod and MP3 Players
®
For Bluetooth
Mobile Phones

Advertisement

Table of Contents
loading

  Also See for Tekkeon myTalker ET7000

  Related Manuals for Tekkeon myTalker ET7000

No related manuals

  Summary of Contents for Tekkeon myTalker ET7000

  • Page 1 ET7000 User Guide Bluetooth Gateway for iPod and MP3 Players ® For Bluetooth Mobile Phones...
  • Page 3: Table Of Contents

    USER GUIDE Contents Overview ..........................2 Getting Started.
  • Page 4: Overview

    Overview myTalker by Tekkeon is a Bluetooth gateway that enables you to make and ™ receive calls from/to your mobile phone while you’re listening to your iPod or MP3 player. myTalker connects between your iPod or MP3 player and the music headsets, so you don’t need to remove your music headsets to take the call.
  • Page 5: Getting To Know Mytalker

    Getting to Know myTalker Microphone Volume Control Mute Talk Lock/Unlock USER GUIDE Audio Jack Add Caller Power USB Power Jack...
  • Page 6: Setting Up Mytalker

    Setting Up myTalker Before using myTalker, you must: • Charge myTalker • Pair myTalker to your mobile phone • Connect myTalker to your iPod or MP3 player Directions for each of these activities are provided in the following three sections. Once these steps are completed, you will be ready to use myTalker! Charging myTalker You must charge myTalker for approximately two hours.
  • Page 7: Pairing Mytalker To Your Mobile Phone

    NOTE: When the battery is low (less than 10% capacity), the amber LED will flash. Pairing myTalker to Your Mobile Phone Pairing is the process of linking a Bluetooth headset/gateway with your Bluetooth mobile phone. Before using myTalker with your mobile phone you must pair the devices.
  • Page 8 To Pair the Devices 1. Turn on the mobile phone and place it next to myTalker. 2. Initiate the Bluetooth device pairing (discovery) feature on the mobile phone. Refer to the mobile phone user guide for instructions on initiating this feature. 3.
  • Page 9: Connecting Mytalker

    To Connect to a Paired Device 1. Follow the menu on the paired device to connect to myTalker. You must be disconnected from all other paired devices with which myTalker is currently connected. To Disconnect from a Paired Device 1. With myTalker connected to a paired device, follow the menu on the device to disconnect from myTalker.
  • Page 10: Using Mytalker

    Using myTalker Powering myTalker To Turn On myTalker 1. Press and hold the POWER button until the blue LED flashes or until you hear the On tone (approximately four seconds). myTalker turns on and is placed in standby mode, ready to make and receive calls. The blue LED will flash at two-second intervals.
  • Page 11: Receiving Calls

    To Make Calls Using Last Number Redial 1. Press and hold the myTalker TALK button. The last number called from your mobile phone will be redialed. You will continue to hear your iPod or MP3 player until the call begins to ring. To Make Calls Using Voice Dialing 1.
  • Page 12: Ending Calls

    If the Call Waiting feature is supported by your phone, you can answer an incoming call while you are connected on another call. In this case, the connected call is placed on hold and the incoming call is connected. While both calls are connected, you can toggle between the calls.
  • Page 13: Adjusting The Volume

    To Transfer Calls from Your Mobile Phone to myTalker 1. With the call connected to your mobile phone, press the myTalker TALK button. The call will be connected to myTalker. To Transfer Calls from myTalker to Your Mobile Phone your phone) 1.
  • Page 14: Muting Mytalker

    Muting myTalker You can mute and unmute the microphone temporarily so that you cannot be heard by the connected party. To Mute myTalker 1. With a call connected to myTalker, press the MUTE button. You will hear a soft beep. To Unmute myTalker 1.
  • Page 15: Call Waiting

    Call Waiting To Answer a Call Waiting Call 1. When you hear two beeps while connected on a call, press the ADD CALLER button. The original call will be placed on hold and the new call be will be connected. Your phone will display the incoming and connected calls. 2.
  • Page 16: Visual And Audible Indicators

    Visual and Audible Indicators Visual Indicators LED Status Blue LED flashes at two-second intervals Blue and amber LEDs flash alternately Amber LED flashes every 32 seconds Both LEDs are off Audible Indicators Tone Description Double beep, increasing in pitch Double beep, decreasing in pitch Pairing Double chime, followed by low beep...
  • Page 17: Troubleshooting

    Troubleshooting Issue When you initiate the Bluetooth device pairing feature on your mobile phone, your phone cannot find myTalker. myTalker is not communicating with your mobile phone. You are encountering poor reception via myTalker. Your mobile phone does not accept voice commands when you are using myTalker.
  • Page 18 Troubleshooting Issue Call reject isn’t working. Call waiting isn’t working. You cannot transfer a call from myTalker to your mobile phone. When you receive a call on your mobile phone, the call is not automatically connected to myTalker after you press the TALK button. (continued) Solution Ensure that your mobile phone supports this feature.
  • Page 19 Troubleshooting Issue Even though myTalker is turned on, the call is not automatically connected to myTalker when you dial a number on your mobile phone. You hear a crackling noise when connected on a call through myTalker. You hear a clicking noise when connected on a call through myTalker.
  • Page 20: Limited Warranty

    This warranty is limited to replacement only and shall not cover any other damages. Any product returned to Tekkeon, Inc. with no fault found will be returned to the owner at the owner’s expense.
  • Page 21: Fcc Statement

    With respect to the use of this product, in no event shall the company be liable for any loss of profit or any other commercial damage, including but not limited to special, incidental, consequential and other damages. FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 22 “Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
  • Page 23: Customer Support

    Customer Support Customer support for myTalker is available at: Tekkeon, Inc. c/o myTalker 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 www.tekkeon.com Tekkeon, Inc. must issue a Return Merchandise Authorization (RMA) number for all exchanges or refunds.
  • Page 24 © 2005 Tekkeon, Inc. All Rights Reserved myTalker is a trademark ™ of Tekkeon, Inc. Rev B 01/06...