Bluetooth v1.2 technology, and is backward compatible with all Bluetooth v1.1 devices. Getting Started Unpacking ezSpeak Your ezSpeak package includes the following: User guide (not shown) ezSpeak Car charger Visor clip Swivel (for visor clip) An optional wall charger is available from the Tekkeon on-line store at www.tekkeon.com.
Getting to Know ezSpeak Volume Up/Volume Down Increases the speaker volume, mutes/unmutes the microphone, and enables scrolling through stored numbers Speaker Answer Button Used to initiate pairing, connect/disconnect the paired phone, and make/receive calls USER GUIDE Charging Lamp Indicates when ezSpeak is being charged or fully charged Power/End Call Button Used to turn on/off...
Setting Up ezSpeak Before using ezSpeak, you must: • Charge ezSpeak • Pair ezSpeak to your mobile phone • Mount ezSpeak to your visor (for in car use) Directions for each of these activities are provided in the following three sections. Once these steps are completed, you will be ready to use ezSpeak! Charging ezSpeak Before using ezSpeak, you must charge the device for a minimum of two hours.
3. Follow the mobile phone/device prompts, and when prompted for the passkey (also called passcode or BT PIN), enter 1234 (the ezSpeak passkey). When pairing is complete, ezSpeak is placed in standby mode, and ET6000 appears on the display. 4. Press to connect ezSpeak with the paired phone.
Mounting ezSpeak When used in a car, ezSpeak is designed to be mounted to your car visor. You can use the visor clip with or without the optional swivel clip. To Mount ezSpeak with the Visor Clip 1. Attach the visor clip to ezSpeak by sliding the clip into the bracket on the rear of ezSpeak as shown.
NOTE: ezSpeak must be connected with the paired phone (the phone name appears in the display). If ET6000 is displayed instead of the phone name, you must connect to ezSpeak before making a call. To Make Calls from Your Mobile Phone 1.
To Make Calls Using Voice Dialing . “Voice Dial” appears on the display and your phone is put into voice dialing mode. 1. Press 2. After you hear a beep (usually between one to four seconds), speak the name of the person you wish to call.
To Receive a Call 1. When you hear ring tone or see “Ringing” and the calling number (if provided) on the display, . The call is automatically connected to ezSpeak and “Call Active” appears in the display. press To Reject an Incoming Call 1.
Transferring Calls You can transfer calls between your mobile phone and ezSpeak. To Transfer Calls from Your Mobile Phone to ezSpeak 1. With the call connected to your mobile phone, press appear on the display and the call is transferred to ezSpeak. To Transfer Calls from ezSpeak to Your Mobile Phone 1.
Muting ezSpeak You can mute and un-mute the microphone temporarily so that you cannot be heard by the connected party. To Mute ezSpeak 1. While in talk mode, press and hold the microphone is muted. To Un-Mute ezSpeak 1. When the microphone is muted, press and hold microphone is no longer muted.
1. Ensure that ezSpeak is charged and turned on. 2. Ensure that your Bluetooth mobile phone is set to Bluetooth mode, and that ezSpeak (ET6000) has been selected as the connected Bluetooth device. (This is important as most Bluetooth phones are designed to pair with more than one Bluetooth device.)
Page 15
Troubleshooting Issue Your mobile phone does not accept voice commands when you are using ezSpeak. You are encountering poor reception via ezSpeak. You hear a crackling noise when connected on a call through ezSpeak. You hear a clicking noise when connected on a call through ezSpeak.
The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will replace the defective product when the owner returns all product contents. The limited warranty will be considered void if the unit is tampered with, subject to misuse, negligence or accidental damage, has been improperly serviced, or if the security seal is removed.
FCC Statement for Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Customer Support If you product is in need of repair or replacement, please contact the Tekkeon Customer Support Center Tekkeon, Inc. c/o ezSpeak 3002 Dow Avenue, #134 Tustin, CA 92780 888-787-5888 / 714-832-1266 www.tekkeon.com Tekkeon, Inc. will issue a Return Merchandise Authorization (RMA) number for all repairs or exchanges.