ST 6002 S OPERATING INSTRUCTIONS VIDEO TechniSat ST 6002 S Stereo AUDIO SKEW ENTER CNCL MUTE MENU TechniSat ST 6002 S STAND BY TechniSat ® 202/ /93 Satellite Receiver Satellitenfernsehprodukte GmbH,TechnikPark, W-5568 Daun TechniSat ST 6002 S TechniSat ST 6002 S...
TechniSat ST 6002 S Contents Diagram : Front Panel, Remote Control Back Panel Important Safety Instructions Main Features of the ST 6002 S Breif Introduction Installation 5.1.1 Connection of the outside unit and television8 5.1.2 Setting up the receiver Operation...
Standby on/off Key Pad ENTER-Button -Button Main Menu -Button Standby LED 4-Fig.Display STAND BY Satellite Selection Channel Selection Buttons (East /West) VIDEO AUDIO SKEW ENTER CNCL MUTE MENU TechniSat ST 6002 S Buttons Video-Menu Audio-Menu Skew-Menu Mute on/off CNCL-Button -Button -Button...
When not in use: If the ST 6002 S is left unattended or unused for long periods of time be sure to unplug the mains connec- tor. The memory is still stored and the internal clock is supplied by an inbuilt battery.
TechniSat ST 6002 S Features of the ST 6002 S: The ST 6002 S has the following features: – 200 preprogrammed channel places – OSD (On-Screen-Display) – Infra-red remote control for all functions – Timer function for 8 settings – Integrated dish positioner –...
"TSG" on the back panel of the ST 6002 S and tune your TV set to channel 36, at which point the test signal (two vertical white stripes) will appear on the screen. Then return the switch to "Video" on the back panel.
Page 8
TechniSat ST 6002 S 5.1.2. Installation of the Receiver Function Button Basic Programming press simultaneously ENTER 3 x Setting East/West Limits ENTER Note: Make sure Hold down until the dish is not west limit is moved too far reached around Hold down &...
TechniSat ST 6002 S If a satelite cannot be found: Sat programming CNCL ENTER hold until a satellite is received ENTER If all Satellites have been programmed CNCL 2 x 5.2. Bedienung Channel Selection MENU ENTER press ENTER Volume Control...
The following instructions assume that the system has been installed correctly so that all the satel- lites can be received. ATTENTION: The ST 6002 S has been pro- grammed for use with a Triple-Band-LNB. With this you can receive all three frequency bands (11 GHz, DBS and 12 GHz).
Page 11
TechniSat ST 6002 S Switch on the receiver using the mains power switch (on the appliance). The following menu appears on the TV screen: To go to the System Menu switch the receiver into stand-by mode using the remote control unit ( ).
TechniSat ST 6002 S E N T E R E N T E R E N T E R 6.1.2 Basic Programming / Initial Set Up Initially to program the receiver you have to carry out a Master Reset. Therefore, move the cursor Reset"...
TechniSat ST 6002 S 6.1.3 Setting the East/West Limits Choose the option "Set Dish Limit" and press ENTER. Then move the cursor to "Position 5000". First move the dish west by pressing > on either RCU or on front panel until the desired west limit is obtained. (Whilst the dish is being moved the position no's will be displayed on the screen.)
TechniSat ST 6002 S 6.1.4 Programming of Satellite Positions Choose the option "Program Satellite " from the System Menu and press ENTER to display a table of parameters. E N T E R Move cursor to "Sat" and use the keys to select the desi- red satellite i.e.
Page 15
TechniSat ST 6002 S Return the cursor to "Sat" and use the buttons to select the satellite which you wish to store next. Repeat the same procedure as described above. All satellites can be stored by this method. NOTE: Not all satellite channels are transmitting continuous- ly.
1. Choose the option “Auto location” on the System Menu. The use of this function requires that ASTRA has already been stored and that a TechniSat actuator is connected to the St 6002 S. Note only satellites with a comparatively strong signal can be stored by this method.
Page 17
TechniSat ST 6002 S 3. Repeat the same procedure for Eutelsat 13,10 E, and then for satellites further west of ASTRA. If you do not find a satel- lite using this method, program it manually as described befo- 4. After you have stored all satellites west of ASTRA, program those which are further east of ASTRA.
C N C L 6.1.6. External Programming It is possible to transfer data between two ST 6002 S or bet- ween a personal computer and the ST 6002 S. To do this you require a cable with two RS 232 connectors. If you wish to exchange data with a personal computer you require in addi- tion the appropriate software (disc).
TechniSat ST 6002 S E N T E R 6.1.7 System Options Move the cursor to the menu option "Change System Options" and press the ENTER button. Choose the appropriate LNB by pressing the buttons on the RCU according to the fol-...
Page 20
TechniSat ST 6002 S E N T E R E N T E R C N C L Frequency shift It is possible to tune in the receiver to the frequency of the LNB should it not be supplying the exact IF-frequency: 1.
Connection of a Videorecorder RF IN UHF OUT To record the signal of the ST 6002 S you can connect the videorecorder either to the “VCR/Dec” LNB PWR OUT DC 14/18V scart socket or to the UHF output. It is also possible to use the video/audio phono sockets.
7.1. General The receiver ST 6002 S has many functions. For ease of use and so that it is not necessary to use a different button for each function the receiver uses "On Screen Display" and function keys. In this way related functions are condensed into "Menus".
TechniSat ST 6002 S 7.2. Direct Operation You can select the desired channel via the Key Pad. Simply select the channel number (see the pro- gram tables). The channel number will appear on the receiver display and also on the screen.
TechniSat ST 6002 S C N C L E N T E R E N T E R 7.3. Menu Operation 7.3.1. Channel Selection Move the cursor to “Channel selection” and press ENTER. Use keys to move the cursor to the desired channel and press ENTER.
TechniSat ST 6002 S E N T E R E N T E R 7.3.2. Satellite Selection Choose the option “Satellite selection” from the menu and press ENTER. A list of all the satellites will appear, those which are stored being marked with a quaver. Move the cursor to the desired satellite and press ENTER.
CNCL. NOTE: having programmed a record time setting you should not switch off the receiver at the mains, otherwise a recording is not possible. To switch the ST 6002 S on and off use only the stand-button. keys. You...
TechniSat ST 6002 S E N T E R E N T E R 7.3.4. Setting the Clock Move the cursor to “Internal clock adjustment” and then press ENTER. Use the position keys to move the cursor to the appro- priate line and keep pressing the data appears.
TechniSat ST 6002 S E N T E R E N T E R 7.3.5. Alignment Dish Position a) If you wish to shift all satellite positions, eg. after a storm has influenced the dish position, first choose a satellite with a less powerful signal.
8. Programming 8.1. General All channels that are known at this time have been stored in the ST 6002 S. However, as new satel- lites and channels frequently can appear, it is possible for you to receive and store these yourself.
TechniSat ST 6002 S E N T E R E N T E R E N T E R C N C L 8.2 Channel Data Changing the channel sequence You can use this function to put the channels in the order which you prefer.
TechniSat ST 6002 S E N T E R E N T E R E N T E R C N C L 8.3 Expanding the Programmable Range of a Satellite Only a certain number of channels are available to each satel- lite unless you choose to extend them eg.
TechniSat ST 6002 S E N T E R E N T E R E N T E R C N C L 8.4 Programming The Channels of new Satellites 1. First program the new satellites as described in the section on "Programming of Future Satellites".
TechniSat ST 6002 S 8.5 Changing the Channel Name Select the channel whose name you wish to alter. Once again select "Channel data" followed this time by "Change Channel Name". E N T E R You can alter the name of the channel using the buttons to select both characters and numbers.
"Decoder" If you wish to connect a decoder to your ST 6002 S, switch to "External". Then the coded reception signal will be sent from the VCR/Dec. scart socket to the decoder. The decoded signal will be sent back to the receiver and can be picked up at any output.
TechniSat ST 6002 S 8.6.2 Audio Menu To call up this menu press the AUDIO button. The following parameters can be changed: "B/W" The audio bandwidth can be switched between 150, 280 or 350 MHz. "De-Emph" You can choose between 50us, J17 and Wegener.
TechniSat ST 6002 S 8.6.3 Skew Menu "Skew" If you wish to fine tune the polarity, you can alter the current of the polariser from -45 mA to +45 mA until you receive a picture of optimum quality. The display of the signal strength may also help you.
TechniSat ST 6002 S Channel Programming: Ch.Nr. Programme ZF MHz PRO 7 1.406 7,02 7,20 1.229 6,50 7,02 SAT. 1 1.288 6,50 7,02 1.523 7,02 7,20 ARD 1 PLUS 1.494 7,02 7,20 3 SAT 1.347 7,02 7,20 NORD 3 1.582...
Page 41
TechniSat ST 6002 S Ch.Nr. Programme ZF MHz POWER FM 1.421 7,38 7,56 1.332 7,38 7,56 RADIO LUX. INT. 1.391 7,38 7,56 SKY RADIO 1.318 7,38 7,56 STAR SAT RADIO 1.406 7,38 7,56 DTSCH. WELLE II 1.229 7,56 6,50 DTSCH. WELLE I 1.229...
Page 42
TechniSat ST 6002 S K.Nr. Programm ZF MHz RTP Internac. 1.575 6,60 7,02 TV 7 (Tunesienne) 1.659 6,60 7,02 Business-TV 1.772 6,60 7,02 Onda C.Musica 7,20 7,02 SER 40 Pricipales 7,38 7,56 SER Convencional 972 7,74 7,02 TV-Ton 7,92 7,02...
Page 43
TechniSat ST 6002 S K.Nr. Programm ZF MHz Cine Cinetti 1.880 5,80 6,40 Canal Plus 1.772 5,80 6,40 France 2 1.814 5,80 6,40 Canal Plus 1.898 5,80 6,40 0,00 0,00 SAT.1 1.073 0,00 0,00 3 sat 1.150 0,00 0,00 ARD Eins Plus 1.304...
Need help?
Do you have a question about the ST 6002 S and is the answer not in the manual?
Questions and answers