Summary of Contents for TechniSat Car Radio
- Page 1 Quality Made in Germany C C a a r r R R a a d d i i o o T T e e c c h h n n i i S S a a t t W W E E R R R R A A 1 1 O O p p e e r r a a t t i i n n g g I I n n s s t t r r u u c c t t i i o o n n s s S S T T E E R R E E O O...
-
Page 2: Compact Instructions
ALTERNATIVE FREQUENCY SEARCH ON/OFF Push for more than 2 sec.: REGIONAL ON/OFF Page 17 Switching: VOLUME/BASS/ TREBLE/FADER Page 7/8 Push for more than 4 sec.: INSTALLATION MENU MODE ON/OFF LOUDNESS ON/OFF Page 8 Push for more than 4 sec.: RESET Page 8 Push: SWITCH ON/SWITCH OFF... -
Page 3: Compact Instructions
FAST FORWARD/FAST REWIND Page 18 Half-push simultaneously: CHANGE TRACK Full-push simultaneously: CASSETTE EJECT FREQUENCY UP/DOWN CODE NUMBER UP/DOWN BAND SWITCHING Page 11 Push for more than 2 sec.: FM/AM SWITCHING Page 11 When entering code: ENTER age 19 PROGRAMME TYPE DISPLAY Page 14 Push for more than 2 sec.: Searching the next programme of the same type... -
Page 4: Table Of Contents
To simplify operation, volume control is effected via an electronic turn-knob. Radio reception/preprogramming comments In addition to the standard FM stations, the TechniSat WERRA 1 is also able to receive MW, LW German band and SW Europe band (49 m). When receiving... -
Page 5: Introduction/Radio Reception/Preprogramming Comments
(interferences of the board electronics of the car) when receiving medium wave stations, particularly weaker ones. In order to have the best possible reception quality it is recommended to use a high-quality AM car antenna. Your TechniSat WERRA 1 is factory-preprogrammed to the following MW stations: 549 kHz Deutschlandfunk... -
Page 6: Safety Precautions
3 Operation 3.1.1 Switching on/off Switching on: - To switch on the unit push the turning knob of the car radio once. The display is not illuminated. If now “C*“ is shown on the display, the security code is activated. -
Page 7: Volume Control
3 Detailed instructions 3.1.2 Volume control higher: - Turn the turning knob clockwise. The volume will be increased. If the letters “CLIP“ appear on the display the “Anti-Clipping“ function is activated to protect your loudspeakers. You should now reduce the volume slightly to enable the amplifiers to work in their normal range again. -
Page 8: Loudness Function
3 Detailed instructions 3.1.4 Loudness function When the volume is low the human ear perceives bass notes worse than middle or high notes.In order to neutralize this effect the unit is equipped with a loudness function increasing the loudness of the bass notes electronically. This function can be switched on resp. -
Page 9: Security Code
Entering the code: The specific code of your TechniSat WERRA 1 is shown on the enclosed code card. Never keep this card together with your car radio as the security code will have no effect in case of a theft. -
Page 10: Adjusting The Number Of Connected Loudspeakers
3.1.8 Adjusting the number of connected loudspeakers The TechniSat WERRA 1 can be operated with two or four loudspeakers. To adapt the device to the number of loudspeakers proceed as follows: - Switch on the car radio (see also 3.1.1). -
Page 11: Radio Unit
3 Detailed instructions 3.2 Radio unit The TechniSat WERRA 1 is equipped with a high-quality radio reception unit for the reception bands FM, MW, SW and LW. The following chapter describes how to use these bands and the functions which are connected with them. -
Page 12: Station Search/Station Memory
3 Detailed instructions 3.2.2 Station search/station memory The TechniSat WERRA 1 offers four different possibilities to search for the radio station: manual station search, automatic station search, AST function and search for the type of programme. The stations which have been found can then be stored separately for each band selected under 3.2.1. -
Page 13: Manual Station Search
3 Detailed instructions Automatic Tuning System: - Shortly push the buttons << >> Depending on the button pushed the frequency range will be searched through downwards or upwards. As soon as a station has been found the Automatic Tuning System will be stopped. AF TP Storing the station: - Select a programme memory position (... -
Page 14: Scan Function
2 seconds until a signal tone can be heard. The TechniSat WERRA 1 is now searching for a station with the same programme type. It stops on the first station which corresponds to the selected programme type. -
Page 15: Automatic Traffic Announcement System
SCAN 3.2.3 Automatic Traffic Announcement System Many FM stations broadcast regional traffic announcements at fixed times. The TechniSat WERRA 1 offers some functions which simplify the use of these announcements: Discerning a station with Automatic Traffic Announcement System: - “TP“ is indicated on the display. -
Page 16: Rds Functions
“TA“ (see 3.2.3). Alternative frequencies (AF): The data of alternative frequencies are transmitted as well. This enables the TechniSat WERRA 1 to always select the station of the programme with the best reception quality. If alternative frequencies are available the letters “AF“ will be displayed. -
Page 17: Stereo/Mono Switching
3 Detailed instructions Shortly push the button. - The function can be switched off by pushing the AF TP - EON: This includes data of other programmes of one station chain (see also 3.2.3). - REG: Some stations have regional programmes which are marked with a respective identification. -
Page 18: Cassette Unit
3 Detailed instructions 3.3 Cassette unit The TechniSat WERRA 1 is equipped with a high-quality stereo auto reverse cassette drive mechanism. This is operated as follows: 3.3.1 Inserting/ejecting a cassette Before you insert the cassette in the slot take care that the tape in the cassette is winded tightly. -
Page 19: Dolby B Noise Suppression
3 Detailed instructions 3.3.4 Dolby B noise suppression The TechniSat WERRA 1 is equipped with the Dolby B noise suppression system which clearly improves the reproduction of cassettes recorded with this system. - You can switch on the noise suppression during the reproduction by shortly pushing the button. -
Page 20: Cd Changer
You can also connect the TechniSat WerraDisc CD changer to your TechniSat WERRA 1. The changer can be controlled via the buttons of the car radio. Please note that your car radio is only suitable for the connection of a TechniSat CD changer. - Page 21 3 Detailed instructions Selecting the title: Selecting next title: - Push the button to play the next title. >> Selecting previous title: - Push the button to play the previous title. << The number of the current title appears on the display. Displaying the running time: The running time of the title can be displayed as follows: - Shortly push the...
-
Page 22: Additional Functions
TechniSat WERRA 1 can be operated. When connecting take care that the power supply for the car radio is covered with at least 10 A. Please also note that it is only possible to connect loudspeakers with an impedance of at least 4 Ohm. -
Page 23: Connection
4 Connection If your car does not have these connection possibilities you can also connect the device as follows. In that case, the ON/OFF switching function via the ignition lock is not activated. The same applies to the security LED. Therefore you should absolutely prefer the previous variant. - Page 24 Quality Made in Germany WERRA 1 is CE-approved and complies with all TechniSat a are registered trademarks of TechniSat requested EU standards! E.&O.E. Issue 5/97 Satellitenfernsehprodukte GmbH · P.O. Box 560 · D-54541 Daun · GERMANY...
Need help?
Do you have a question about the Car Radio and is the answer not in the manual?
Questions and answers