Related Manuals for THOMSON SCENIUM DPL5000
Summary of Contents for THOMSON SCENIUM DPL5000
- Page 1 THOMSON 46, quai Alphonse Le Gallo 92648 Boulogne Cedex FRANCE TOCOM User’s Guide DPL5000 Audio Video Receiver www.thomson.net...
-
Page 2: Table Of Contents
Safety Information Rating Information: At bottom / back of the unit this unit comply with the existing requirements In accordance with the rating plate of the T H E L I G H T N I N G unit, this unit complies with current FLASH AND ARROW- standards concerning electrical safety and HEAD WITHIN THE... -
Page 3: Getting Started
Getting Started Unpacking the Receiver You should receive the following items: SUBWOOFER SOURCE SURROUND PRESET ON/ECO VOLUME PHONES One pair of “AAA” One receiver unit batteries one audio cable (two One pig-tail One external AM loop wires) with red and antenna wire white RCA connectors;... -
Page 4: Connecting To Audio-Visual Components
Getting Started Connecting to Audio-Visual Components S-VIDEO If your CD player is equipped with digital optical jacks, If your video component has a S-Video jack included, you use of optical cable is preferred. What you need is just one more digital optical cable (not supplied). Plug it in can make use of it to enjoy enhanced video quality by the digital input jack of the receiver and select connecting it to the relevant S-Video jack at the rear side... -
Page 5: Connecting The Speakers
Getting Started Connecting the Speakers Speaker wires One for each speaker, is needed for connection. Press down on the tab to open the terminal and insert the FRONT SPEAKERS REAR SPEAKERS wire. Release tab to lock wire in the terminal. Antenna and Speaker Wire Connection SUBWOOFER Push terminal tab down to... -
Page 6: Preferred Surround Placement
Getting Started Preferred surround placement Advanced Setting Alternative Surround Placement Location Rear wall If possible, place surround speakers to either side of the listening area, not behind it. If rear wall mounting is the only choice, aim the speakers at each other (A), towards the front (B) or even towards the sidewalls (C, D). -
Page 7: Operating Your Receiver
Operating Your Receiver Receiver Controls ON/ECO 1. ON/ECO 6. PRESET Buttons Turns the unit on and off. When the system is turned Selects preset station in Tuner mode. on, the unit will go to the mode it was in before powered off. -
Page 8: Switching The Unit On/Off
Operating Your Receiver Display DVD / VCR / SAT / TUNER / TAPE / CD / TV TUNED • An arrow points to the current source mode. • Tuner station detected. • Dolby Digital audio input for signal format. • Speaker Icons. L - Front left speaker C - Center speaker R - Front right speaker... -
Page 9: Using The Remote To Control Additional Components
Operating your Receiver You can connect up to 6 audio/video sources to this Using the Remote to Control Additional amplifier: Components Source button Corresponding connector You can use your remote to control most of Thomson (receiver front panel) (receiver back panel) branded VCRs, satellites, cable boxes or TVs. -
Page 10: Operating The Radio
Operating your Receiver Operating the Radio Automatic Tuning The receiver has a built-in tuner that allows for AM/FM Press and hold TUNER - or radio function. TUNER + for about one second to activate the automatic SEARCH function. Manual tuning The receiver will automatically tune 1. -
Page 11: Advanced Sound Control
Operating your Receiver RDS (Radio Data System) for FM Only NOTE The RDS icon shows on display when RDS data are received. The following information may be available NO PTY will be displayed if selected kind of on certain stations: program is not broadcasted •... -
Page 12: Fine Setting Of Components
Advanced Sound Control Dolby 3 Stereo NOTE The 3 Stereo mode will redirect the Surround signals to the front left and right speakers when only the front and center speakers are used. Night mode is available only with Dolby Digital playback. -
Page 13: Fine Setting Of The Speakers
Advance Sound Control Fine Setting of the Speakers Adjust Individual Speaker Volume All the basic settings have already been preset for the 1. To adjust individual speaker volume level, press the speakers included in the box. LEVEL button on the remote control. Also, to make the surround sound more effective and suit the acoustic conditions in your listening room, you 2. -
Page 14: Troubleshooting Tips Troubleshooting Tips
Troubleshooting Tips Troubleshooting Tips General Receiver/Tuner Operation No audio. • Make sure the speakers are connected. ST indicator is off. • Check the input connections. • Check the power cord connections. • Adjust the antenna. • Make sure the MUTE signal on the front panel is off. •...