Husqvarna Automower 420 Workshop Manual page 11

value is 100%. If the value is lower, the loop system
does not function correctly and thus none of the
displayed signals are correct.
4.4.1.4 Tools - Info - Sensors
Tools - Info - Sensors menu has 2 sections:
The
• Status
Temperature
•
Info - Sensors - Status menu has this information:
The
Collision : When the collision sensors are activated
•
YES .
the display shows
Lifted : When the body is lifted up the lift sensor is
•
activated and the product display shows
• Tilted : When the product is standing horizontally the
value should be max ±3. Inclination up and to the left
is shown as negative values.
Normal position : Yes : the product is standing in a
•
No : the product is upside down.
normal position,
The Info - Sensors - Temperature menu has this
information:
Product temperature : The temperature measured
•
by a temperature sensor on the main circuit board.
LCD temperature : The temperature measured by a
•
temperature sensor on the HMI circuit board.
4.4.1.5 Tools - Info - Ultrasonic
Tools - Info - Ultrasonic menu shows:
The
U.SONIC : The version of the ultrasonic program.
•
Status : Shows if the sensors are active, ON or OFF .
•
The ultrasonic sensors are only active when the
product is operating.
Error : Shows the error code if there is an error with
•
the sensors:
1-4, 6 and 8 : Communication failure between the
•
ultrasonic circuit board and the main circuit
board.
5 : Electronic problem
•
7 : Continuous detection of obstacle due to
•
obstacle stuck in the sensors for more than 15
minutes or due to vibration.
4.4.1.6 Tools - Info - Automower
®
Automower Connect menu shows:
The
COM : the version of the program on the
•
communication board.
SIM card :
•
OK : Connected.
•
PIN : SIM PIN is required.
•
PUK : SIM PUK is required. To enter the PUK
•
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
1191 - 001 -
Yes .
®
Connect
Locked : The SIM card is locked. The SIM card
•
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
Error : Other fault.
•
- : Automower ®
• Connect is not active or no SIM
card is inserted.
GPRS :
•
Ok : The communication status with the app.
•
Note: The communication status must be
there is no communication with the app.
Error : Not connected, no GRPS link.
•
• Search : Not connected, GPRS link ok.
Blocked : The communication board is blocked.
•
The serial number of the circuit board is not
registered on Husqvarna server. Replace the
communication board.
SIMs : Data is not transmitted. Automower
•
connect is attempting to transmit data but the
Husqvarna server is not receiving.
Note: If the SIM card is a cash SIM card and
there is no money left, this can cause the
code.
PIN : SIM PIN is required.
•
PUK : SIM PUK is required. To enter the PUK
•
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
Locked : The SIM card is locked. The SIM card
•
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
Error : Other fault.
•
- : Automower ®
• Connect is not active or no SIM
card is inserted.
• Data : Data transmission On/Off .
SMS : SMS function On/Off .
•
RSSI : The signal strength of GPRS reception,
•
between 0-98. A higher the value means a better
reception. The value must be more than 10 for a
stable connection.
Carrier : The name of the operator.
•
APN : The APN used for the operator
•
APN user : User name for APN
•
APN pwd : Password for APN
•
• GPS signal : The strength of the GPS reception. In
order to set the center position of the Geofence, the
GPS signal must be
4.4.1.7 Tools - Info - Motors
Tools - Info - Motors menu has these sections:
The
Special menus 420/430X/430XH/440/450X/
Strong .
450XH - 11
Ok or
SIMs