Tascam IF-FW/DM Owner's Manual
Tascam IF-FW/DM Owner's Manual

Tascam IF-FW/DM Owner's Manual

Firewire interface card

Advertisement

Quick Links

»
D00830000B
IF-FW/DM
FireWire Interface Card
OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IF-FW/DM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tascam IF-FW/DM

  • Page 1 » D00830000B IF-FW/DM FireWire Interface Card OWNER'S MANUAL...
  • Page 2: Table Of Contents

    Your experience with the IF-FW/DM will be greatly enhanced by a good working knowledge of your audio soft- ware. Be sure to check the TASCAM web site at www.tascam.com to ensure you have the...
  • Page 3: Features

    V1.20 or higher. DM-24 Requirements The DM-24 must be running V3.00 software to use the IF-FW/DM. Please refer to www. tascam.com or your local service center to obtain this update. Do not proceed to install the IF-FW/DM until your DM-24 is running V3.00 or higher.
  • Page 4: Installation

    1. Remove the five screws holding the blank plate or card currently installed in Slot 1 then remove the plate or card. 2. Insert the IF-FW/DM into Slot 1, mak- ing sure that the card edges slide into the white plastic guide inside Slot 1. Push it all the way in until it clicks and the card back plate is flush with the mixer’s back...
  • Page 5: Making Connections

    Making Connections 1. Connect one end of the provided FireWire cable to the IF-FW/DM and the other end to an available FireWire port on your computer. An inferior FireWire cable can negatively affect the performance of the system. • For Windows installations, do not make this connection until instructed to do so by the driver installer.
  • Page 6: Installation

    8. Click “Next” in the Setup/Installation window. 9. The Setup/Installation window will pres- ent a “Finished” message. Click Exit. 10. Your IF-FW/DM is installed and ready to use. Windows 64-Bit Windows driver version 1.10 & higher includes untested 64-bit drivers (requires 64-bit PC hardware and 64-bit Windows OS).
  • Page 7: Setup

    1. Under the Setup menu, select Configure Audio System > Configure Hardware Driver 2. Highlight the IF-FW/DM to make it the selected Core Audio device for DP you need more detailed instructions to con- figure your application, please refer to the documentation for your application to set up an audio/MIDI interface.
  • Page 8: Dm-3200

    Mixer Outputs DM-3200 By default, the DM-3200 duplicates busses 1 - 8 on IF-FW/DM mixer outputs 17 - 24. Also available are the Direct Outputs from channels 1 - 16. By default, those appear on IF-FW/DM mixer outputs 1 - 16.
  • Page 9: Dm-3200

    DM-24 By default, the DM-24 duplicates busses 1 - 8 on IF-FW/DM mixer outputs 1 - 8, 9 - 16, and 17 - 24. Also available are the Direct Outputs from channels 1 - 16 on the DM-24. By default, those appear on IF-FW/DM mixer outputs 1 - 16.
  • Page 10: The If-Fw/Dm Control Panel (Windows)

    O S etup IF-FW/DM Control Panel (Windows) The IF-FW/DM Control Panel is found here: Start Menu > All Programs > TASCAM There are three sliders available in the con- trol panel. Generally, lower audio buffer settings offer lower latency but require a more powerful computer.
  • Page 11: Enable Wdm

    Setup Enable WDM When first installed, the IF-FW/DM will 4 active stereo pairs of audio through its WDM driver. If you are using a DAW that can- not use ASIO and you want to access all 24 channels of audio, click this option. It may...
  • Page 12 » IF-FW/DM TEAC CORPORATION Phone: +81-422-52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: +1-323-726-0303 7733 Telegraph Road, Montebello, California 90640 TEAC CANADA LTD. Phone: +1905-890-8008 Facsimile: +1905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.A. De C.V Phone: +52-555-581-5500 Campesinos No.

This manual is also suitable for:

If-fwIf-dm

Table of Contents