Tascam US-224 Use Manual
Tascam US-224 Use Manual

Tascam US-224 Use Manual

Using the us-224 with digital performer
Hide thumbs Also See for US-224:

Advertisement

Quick Links

Using the US-224 with Digital Performer

Before setting up the US-224 to work with Digital Performer, please install the US-224 MacOS
drivers, and set up the FreeMIDI. (Refer to the enclosed documents on setting up both the drivers
and FreeMIDI.) You must be using D

Setting Up

Begin the setup procedure below with the US-224 plugged in and powered on.
Locate the Digital Performer Control Surface Plugin on the US-224 CD-ROM. (If you've
downloaded the driver from our website, locate the folder on your hard drive.) Drag it into
the P
-
folder within the D
LUG
INS
Important: The Control Surface Plug-in must be in the P
P
folder, along with the Digital Performer application itself.
ERFORMER
Next, verify that the ASIO drivers are installed correctly. Open the ASIO D
within the D
IGITAL
bit and 24 bit ASIO drivers.
Open the US-224 Control Panel (Apple menu). Select US-224 N
menu. If you will be using a Master fader within Digital Performer, then also select
"Master fader sends MIDI only." Otherwise, select "Master fader affects application output
and sends MIDI."
Open Digital Performer. Select an existing project, or open a new one.
From the B
ASICS
D
.... From the pulldown menu that appears, select the ASIO device option, and
RIVER
then select one of the US-224's ASIO drivers.
Select the B
ASICS
menu, select the US-224 as the Control Surface. Select "US-224, C
MIDI C
OMMUNICATION
P
IGITAL
ERFORMER
P
IGITAL
P
folder. Verify that this folder contains both the US-224's 16
ERFORMER
/ MOTU A
S
UDIO
YSTEM OPTIONS
/ C
S
S
ONTROL
URFACE
drop down menu.
2.7 or later.
folder.
ERFORMER
-
LUG
INS
menu, select C
menu. From the H
ETUP
folder within the D
IGITAL
folder
RIVERS
from the pulldown
ATIVE
H
ONFIGURE
ARDWARE
pulldown
ARDWARE
-16" from the
ONTROL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the US-224 and is the answer not in the manual?

Questions and answers

Summary of Contents for Tascam US-224

  • Page 1 Using the US-224 with Digital Performer Before setting up the US-224 to work with Digital Performer, please install the US-224 MacOS drivers, and set up the FreeMIDI. (Refer to the enclosed documents on setting up both the drivers and FreeMIDI.) You must be using D Setting Up Begin the setup procedure below with the US-224 plugged in and powered on.
  • Page 2 SET + LOCATE> Channel Controls The US-224 has 4 channel strips and a master fader. The master fader controls the volume for any and all tracks that contain master faders. Regular channel strip faders never affect a master fader track.
  • Page 3 The REC button acts like a shift key with the SELECT buttons. Holding REC and pressing a SELECT button toggles the record enable state for that track. SET+REC clears all record- enabled tracks. The MUTE buttons control both mute and solo status of a track. When the SOLO pressing a MUTE button toggles the mute status of a track, and the MUTE status of the track.
  • Page 4 Fader Nulling When changing banks, the physical fader position may not match the corresponding channel’s on-screen fader’s position. Pressing the NULL button places the US-224 into Null mode and lights the NULL . In this mode, the fader strips’ red REC and green SELECT whether the fader is too high (REC physical fader matches the on-screen fader’s position.

Table of Contents