TANDBERG D1392602 User Manual
  1. Manuals
  2. Brands
  3. TANDBERG Manuals
  4. Network Card
  5. D1392602
  6. User manual
TANDBERG D1392602 User Manual

TANDBERG D1392602 User Manual

Tandberg video portal data port command interface user guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TANDBERG Video Portal
Data port Command Interface User Guide
TANDBERG Video Portal
Data port Command Interface User Guide
Software version V 3
D1392602
TANDBERG
D1392602
1

Advertisement

Table of Contents
loading

Summary of Contents for TANDBERG D1392602

  • Page 1 TANDBERG Video Portal Data port Command Interface User Guide TANDBERG Video Portal Data port Command Interface User Guide Software version V 3 D1392602 TANDBERG D1392602...

  • Page 2: Table Of Contents

    CONNECTING TO THE DATA PORT COMMAND INTERFACE THROUGH THE RS-232 PORT. 4 2.1. ARDWARE AND ABLING 2.2..4 ROUBLESHOOTING CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET ... 6 THE TANDBERG VIDEO PORTAL COMMANDS ... 7 4.1..7 NTRODUCTION 4.1.1. Command format... 7 4.1.2. Command types ... 7 4.2.

  • Page 3: Introduction

    If, after reading this manual, you require additional information concerning the use of the TANDBERG Video Portal Data port Command Interface, please contact your local TANDBERG dealer who will be able to supply you with relevant information for special applications.

  • Page 4: Connecting To The Data Port Command Interface Through The Rs-232 Port

    Pin no Signal NOTE! A straight through cable should be used between the TANDBERG Video Portal’s RS-232 port and the DTE. The figure below illustrates the recommended cable-wiring scheme for connecting the Video Portal to a PC through RS-232.
  • Page 5 TANDBERG Video Portal If communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the following should be checked: • Verify that the serial cable is a straight through 9-pin to 9-pin cable • Confirm that the configuration of the PC/terminal’s serial RS-232 port is identical to the configuration of the TANDBERG Video Portal RS-232 port.

  • Page 6: Connecting To The Data Port Command Interface Using Telnet

    TANDBERG Video Portal Release V3.0 SW Release Date: 2007-03-13 NOTE! If the TANDBERG Video Portal has been protected with an IP password you will be prompted to enter this password before you can access the Data port Command Interface via Telnet.

  • Page 7: The Tandberg Video Portal Commands

    TANDBERG Video Portal The TANDBERG Video Portal Commands 4.1. Introduction Typing ‘?’ or ‘help’ when connected to the Data Port Command Interface will return a list of valid commands. The commands are used to control the functions of the Video Portal. A command may be followed by a set of parameters and sub-commands.

  • Page 8: The Commands

    TANDBERG Video Portal • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The command Xconf telnet mode: "on" enables telnet access on the Video Portal. If the command is syntactically correct the Video Portal returns OK, otherwise the Video Portal returns ERROR.

  • Page 9: System Configuration Commands

    TANDBERG Video Portal 4.2.1. System Configuration Commands Command: Description: Mapping of a call onto a service or another call. alplan Dialplan Entry [1..64] Enabled: <On/Off> Dialplan Entry [1..64] Name: <S: 0, 30> Dialplan Entry [1..64] NetType: <All/H324m/H323/SIP> Dialplan Entry [1..64] Prefix: <S: 0, 128>...
  • Page 10 TANDBERG Video Portal distinguished: • • • • • • • Example of a DID Dialplan for mobile to SIP calls: Note: • • • *c xConfiguration Dialplan Entry 1 Enabled: On *c xConfiguration Dialplan Entry 1 Name: "H324m - SIP"...
  • Page 11 TANDBERG Video Portal *c xConfiguration Dialplan Entry 1 Prefix: "207947133" *c xConfiguration Dialplan Entry 1 Suffix: "" *c xConfiguration Dialplan Entry 1 ServiceId: 1 *c xConfiguration Dialplan Entry 1 Property 1 Name: "nettype" *c xConfiguration Dialplan Entry 1 Property 1 Value: "SIP"...
  • Page 12 TANDBERG Video Portal *c xConfiguration Dialplan Entry 2 Property 2 Name: "avmode" *c xConfiguration Dialplan Entry 2 Property 2 Value: "4" *c xConfiguration Dialplan Entry 2 Property 3 Name: "prefix" *c xConfiguration Dialplan Entry 2 Property 3 Value: "" *c xConfiguration Dialplan Entry 2 Property 4 Name: "suffix"...
  • Page 13 TANDBERG Video Portal *c xConfiguration Dialplan Entry 4 Prefix: "90370010" *c xConfiguration Dialplan Entry 4 Suffix: "" *c xConfiguration Dialplan Entry 4 ServiceId: 3 *c xConfiguration Dialplan Entry 4 Property 1 Name: "allowredirectep" *c xConfiguration Dialplan Entry 4 Property 1 Value: "0"...
  • Page 14 TANDBERG Video Portal *c xConfiguration Dialplan Entry 4 Property 14 Name: "entry5_label" *c xConfiguration Dialplan Entry 4 Property 14 Value: "Menu" *c xConfiguration Dialplan Entry 4 Property 15 Name: "entry5_nettype" *c xConfiguration Dialplan Entry 4 Property 15 Value: "H323" *c xConfiguration Dialplan Entry 4 Property 16 Name: "entry5_bnumber"...
  • Page 15 TANDBERG Video Portal Xconf H323Gatekeeper Authentication *c xConfiguration H323Gatekeeper Authentication Address: “abc.def.ghi.jkl” *c xConfiguration H323Gatekeeper Authentication Mode: Off *c xConfiguration H323Gatekeeper Authentication ID: "" HTTP Enables or disables access to HTTP services. NOTE! Changes become effective after reboot. HTTP Mode <On/Off>...
  • Page 16 Example of Service feedback: *c xConfiguration Services Service 1 Enabled: On *c xConfiguration Services Service 1 Name: "Direct Inwards Dialing" *c xConfiguration Services Service 1 ServiceFile: "/tandberg/services/did.ivr" *c xConfiguration Services Service 1 Logging: On Session Sets a timeout time for sessions like telnet, ssh etc.
  • Page 17 *c xConfiguration SIP Interface Server Type: Auto *c xConfiguration SIP Interface Transport Default: UDP SNMP Configures the SNMP. Note! For more information about SNMP please read the TANDBERG SNMP application note. SNMP Mode < On/Off/ReadOnly/TrapsOnly > SNMP CommunityName: <S: 0, 16> SNMP SystemContact: <S: 0, 70>...
  • Page 18 TANDBERG Video Portal *c xConfiguration SNMP SystemContact: "" *c xConfiguration SNMP SystemLocation: "" *c xConfiguration SNMP HostIPAddr 1: "127.0.0.1" *c xConfiguration SNMP HostIPAddr 2: "127.0.0.1" *c xConfiguration SNMP HostIPAddr 3: "127.0.0.1" Enables or disables SSH interface on the Video Portal SSH Mode: <On/Off>...

  • Page 19: General Video Portal Commands

    TANDBERG Video Portal 4.2.2. General Video Portal Commands Command: Description: This command sets the path and address of the TMS server. A message is sent to TMS when the ExternalManager Video Portal starts up to signal TMS that the Video Portal is ready.

  • Page 20: System Status Commands

    TANDBERG Video Portal 4.2.3. System Status Commands Command: Description: Shows the dialplan configuration. Dialplan Example: *s Dialplan 1: Entry: DialplanEntryId: 1 Enabled: On Name: "H323 - SIP" NetType: H323 Prefix: "9047123456" Suffix: "" ServiceId: 2 Property: Name: "nettype" Value: "SIP"...
  • Page 21 TANDBERG Video Portal Ethernet Displays the configuration of the Ethernet interface Ethernet Status format: < MacAddress> <Speed> Parameters: • MacAddress, The mac address of the Ethernet interface • Speed, The speed of the interface, possible values are Auto/10half/10full/100half/100full. Example of Ethernet feedback *s Ethernet: MacAddress: "00:0E:0C:5C:B5:7D"...
  • Page 22 TANDBERG Video Portal Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" Expression: "" *s/end Displays the status of the connection with the gatekeeper. H323Gatekeeper...
  • Page 23 TANDBERG Video Portal Parameters: • Address, the IP address of the Video Portal • SubnetMask, the subnetmask used for the connected network • Gateway, the gateway to route traffic to an IP number outside the connected network • DNS Server [1.. 5] Address, the IP numbers of maximum 5 DNS servers •...
  • Page 24 TANDBERG Video Portal Options Parameters: ---- Example of Options feedback: *s Options: Option 1: Key: "115201P1-1-43F072FC" Description: "1 trunk" *s/end Service Displays all configured/uploaded services. Service Status format: Service [1..64] Example of Service feedback: *s Service 1 (status=Active): ServiceId: 1 Enabled: On Name: "Direct Inwards Dialing"...
  • Page 25 • TemperatureCelcius, temperature of the main board in Celcius • TemperatureFahrenheit, temperature of the main board in Fahrenheit Example of SystemUnit feedback: *s SystemUnit: ProductType: "TANDBERG Video Portal" Uptime: 15123 Software: Version: "R3.0Beta2 (TEST SW)" Name: "test" ReleaseDate: "2007-03-21, 17:54"...

  • Page 26: Debug Commands

    TANDBERG Video Portal Configuration: PRI:41 TemperatureCelcius: NA TemperatureFahrenheit: NA *s/end 4.2.4. Debug Commands Command: Desription: Syslog Enables a real-time log of Bonding, H.221 and H324m, ISDN, RTSP, IVider, and IVider Engine activity. Note! H323 and SIP logging is presented using the following command: tsh –a H323 (SIP).
  • Page 27 TANDBERG Video Portal Example: xCommand Boot *r Result (status=OK): / *r/end CUIL reboot request, restarting CheckDisk This command shows the presence and the status of the internal harddisk. Example: xCommand CheckDisk *r Result (status=OK): CheckDisk: "Disk present" CheckDisk: "Disk mounted"...
  • Page 28 TANDBERG Video Portal Dial This command establishes a dial out to an end point Parameters: • • • • OK Result parameter: • Example: xCommand Dial CalledParty:0612345678 CallingParty: 0207947123 Nettype: H324m Calltype: Vtlph *r Result (status=OK): Dial: "dial:904023_5" *r/end DialplanEntryDelete This command deletes the indicated entry of a dialplan.
  • Page 29 TANDBERG Video Portal Example: xCommand DisconnectCall ABCD123456 *r Result (status=OK): *r/end This command wipes all the data from the internal harddisk EraseDisk Example: xCommand EraseDisk *r Result (status=OK): *r/end FeedbackDeregister Command used to deregister XML feedback over HTTP(S). Parameters: •...
  • Page 30 TANDBERG Video Portal • • Example: xCommand feedbackregister url:http://10.47.14.185:8000 *r Result (status=OK): ID: 2 *r/end OptionKeyAdd Command used to set new option keys. Parameters: • NOTE! Always reboot the system after adding option keys, for the option key to take effect.
  • Page 31 TANDBERG Video Portal Example (Delete Service nr. 10): xCommand ServiceEntryDelete 10 *r Result (status=OK): / *r/end Command used to swap service numbers. ServiceEntrySwap Parameters: • • Example (Swap Service nr. 10 & 11): xCommand ServiceEntrySwap ServiceEntryNumber: 10 ServiceEntryNumber2: 11 *r Result (status=OK): /...

  • Page 32: Commands

    TANDBERG Video Portal General User Commands About Shows following system information: Software version: R3.0 Portions of this software are licensed under 3rd party licenses. See the CD accompanying this product for details. Help or ? Displays the help menu. help...
  • Page 33 TANDBERG Video Portal "xfeedback register status/call" - to monitor call changes "xfeedback register status/call--" - to monitor only call state changes "xfeedback register configuration" - to monitor all configuration changes The special command xhistory presents the status of the last 255 calls, made to or from the Xhistory Video Portal,via a cyclic buffer mechanism.

Table of Contents