Cisco BWX 8305 Installation And Commissioning Manual page 28

Table of Contents

Advertisement

Installation
4.4 Installation
Check content of boxes.
Check content of boxes.
Make sure nothi ng is mi s sing
Make sure nothi ng is mi s sing
Check that the Antenna has a
Check that the Antenna has a
printed sheet with losses
printed sheet with losses
measured in the lab and a CD with
measured in the lab and a CD with
the RFS electrical parameters
the RFS electrical parameters
Sweep the bundled and jumper
Sweep the bundled and jumper
cables and compare with the value
cables and compare with the value
in the factory label. Enter the total
in the factory label. Enter the total
from the factory labels in the
from the factory labels in the
Closeout Tool
Closeout Tool
Sweep the Antenna and compare
Sweep the Antenna and compare
with the values i n the printed
with the values i n the printed
sheet. Enter the measured results
sheet. Enter the measured results
top half of the
top half of the
RFS & RFS Cable Loss
RFS & RFS Cable Loss
Mount the Antenna on the tower,
Mount the Antenna on the tower,
building, or other structure,
building, or other structure,
Connect the Main cables to the
Connect the Main cables to the
surge protectors at the Antenna
surge protectors at the Antenna
Connect the Main cables from
Connect the Main cables from
the Antenna to the lower bus bar
the Antenna to the lower bus bar
BWX 8305 Basestation Installation and Commissioning Guide
4-4
Installation – (for each BS at the cell site)
B
B
Cable Loss
Cable Loss
tab
tab
in the
in the
Closeout Tool
Closeout Tool
tab
tab
and ground it.
and ground it.
Install surge protectors
Install surge protectors
in the Antenna
in the Antenna
Install the lower bus bar
Install the lower bus bar
with surge protectors
with surge protectors
If using a combiner, sweep it to
If using a combiner, sweep it to
determine the associated insertion
determine the associated insertion
loss.
loss.
Install and connect Combiner.
Install and connect Combiner.
Sweep the Antenna and the cables
Sweep the Antenna and the cables
together and enter the measured
together and enter the measured
results in the bottom half of the
results in the bottom half of the
Closeout Tool
Closeout Tool
RFS & RFS
RFS & RFS
Cable Loss
Cable Loss
tab
tab
Install the BS unit in the
Install the BS unit in the
mounting rack or outdoor
mounting rack or outdoor
enclosure and ground i t
enclosure and ground i t
Connect the 9 jumper cables from
Connect the 9 jumper cables from
the lower Bus bar to the front of the
the lower Bus bar to the front of the
BS (either directly or through the
BS (either directly or through the
combiner)
combiner)
Sweep the GPS cable.
Sweep the GPS cable.
Install the GPS antenna
Install the GPS antenna
Connect the GPS cable
Connect the GPS cable
to the GPS antenna and
to the GPS antenna and
to the surge protector
to the surge protector
in the lower Bus bar
in the lower Bus bar
Mount the BWX 8303 Basestation
Mount the BWX 8303 Basestation
Timing System in the rack and
Timing System in the rack and
ground it
ground it
Verify all the BS cables are
Verify all the BS cables are
properly connected and
properly connected and
weatherproofed
weatherproofed
Chapter 4
I&C Process
Check the power voltage
Check the power voltage
and connect the BS, BWG,
and connect the BS, BWG,
and BWX 8303 to power
and BWX 8303 to power
Connect the BS, BWX 8303, BWG,
Connect the BS, BWX 8303, BWG,
and Server to an Ethernet Switch
and Server to an Ethernet Switch
Verify the BWX 8303 performance
Verify the BWX 8303 performance
(Power up and lock in)
(Power up and lock in)
Mount BWG unit
Mount BWG unit
And boot up
And boot up
Verify access to a AAA server
Verify access to a AAA server
Verify access to a DHCP server for
Verify access to a DHCP server for
IP addressing
IP addressing
To run Test EMS,
To run Test EMS,
use two straight through
use two straight through
Ethernet cables to connect
Ethernet cables to connect
the BS Data port to the installer's
the BS Data port to the installer's
laptop through the
laptop through the
Ethernet switch
Ethernet switch
Connect the console port of the BS
Connect the console port of the BS
to the serial port of the Installer's
to the serial port of the Installer's
laptop and start a Terminal
laptop and start a Terminal
Emulation window
Emulation window
C
C
NOW YOU CAN POWER UP
NOW YOU CAN POWER UP
THE BS FOR THE INITIAL
THE BS FOR THE INITIAL
BOOT!!!
BOOT!!!
OL-16336-02

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents