Stopping Your Dryer; Pausing Or Restarting; Control Locked - Kenmore 110.9772 Use And Care Manual

To make changes during an Auto Cycle:
Press STOP once.
Adjust Dryness Level.
NOTE: Dryness Level selections can be made only while
using Auto Cycles. You can select a different dryness
level, depending on your load, by pressing Dryness Level
and choosing More Dry, Normal or Less Dry. Selecting
More Dry, Normal or Less Dry automatically adjusts the
sensed time needed.
How Auto Dry works
SmartHeat™ improves drying performance with Auto Moisture
Sensing Plus, which advances the cycle as moisture is extracted
from clothing. A thermistor (electronic temperature sensor) and
moisture sensing strips in the dryer drum help measure the
amount of moisture in the clothes as they tumble. An electronic
control determines the load type to help save time, avoid
overdrying, and increase the accuracy of the end dryness level.
After the first 5 minutes of an automatic cycle, the estimated time
display will adjust based on the approximate load size, cycle,
dryness level selected and amount of moisture left in the clothes.
When the clothes have reached approximately 80% of the
dryness level selected, the estimated time display will adjust
again, showing the final drying time. Auto Moisture Sensing Plus
takes the guesswork out of drying time and enhances fabric care.
To use a Timed Cycle
NOTE: A light next to each feature will glow green when the
feature is selected or will glow amber when the feature is
selectable.
Press a Timed Cycles button.
Press MORE TIME or LESS TIME until the desired drying
time is displayed. Tap MORE TIME or LESS TIME, and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME, and the time will change by
5-minute intervals.
NOTE: The More Time and Less Time buttons can be
used only with Timed Cycles and the Touch Up Cycle.
Press TEMPERATURE until the desired temperature
glows.
NOTE: During a Timed Cycle, you can change the settings for
Time, Temperature, WRINKLE GUARD
Signal. Press STOP twice to stop the dryer and clear the
settings. Select another cycle or option.
To use a SteamCare Cycle
NOTE: A light next to each feature will glow blue when the
feature is selected or will glow amber when the feature is
selectable.
Use of a fabric softener sheet is not recommended with
SteamCare cycles as it may cause temporary staining on
clothes.
16
4. (OPTIONAL STEP) If desired, select OPTIONS. For more
5. (OPTIONAL STEP) If desired, set the End of Cycle Signal.
6. Press and hold START for approximately 3 seconds until
To stop your dryer at any time
Press STOP twice or open the door.
To pause the dryer at any time
Open the door or press STOP once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
® and End of Cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the Control Locked feature to
avoid unintended cycle or option changes during dryer operation.
To enable the Control Locked feature:
Press and hold CYCLE SIGNAL for 3 seconds. The Control
Locked indicator light glows, and a single beep tone is heard. To
unlock, press and hold CYCLE SIGNAL for 3 seconds. The
indicator light turns off.
Press the POWER button. Then rotate the dial to select
the SteamCare Cycle. The indicator light for the selected
cycle will glow blue. The preset modifiers for the selected
cycle will glow green. Selectable options will glow amber.
If an option or modifier is unavailable with the selected
cycle, the light will not illuminate. The actual cycle time (in
minutes) will show in the display.
Press MORE TIME or LESS TIME until the desired drying
time is displayed. Tap MORE TIME or LESS TIME, and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME, and the time will change by
5-minute intervals.
NOTE: The More Time and Less Time buttons can be
used only with Timed Cycles and the Touch Up Cycle.
Press TEMPERATURE until the desired temperature
glows.
NOTE: During the Touch Up Cycle, you can change the
settings for Time, Temperature, WRINKLE GUARD
of Cycle Signal. During the Refresh Cycle you can change
®
WRINKLE GUARD and the End of Cycle Signal. Press STOP
twice to stop the dryer and clear the settings. Select another
cycle or option.
details, see "Options."
Select LOUD or SOFT by pressing the Cycle Signal button to
alert you when a cycle ends.
dryer starts. Be sure the door is closed.
If you do not press START within 5 minutes of selecting
the cycle, the dryer automatically shuts off.
If you wish to end your drying cycle after pressing Start,
press STOP twice.

Stopping Your Dryer

Pausing or Restarting

Control Locked

® and End