Preface About this manual This manual is designed to make it easy to use the SRC- 3000b Touch Screen Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents.
3.2 Code and Learn Setting Key ... 11 3.3 Using Pre-programmed Code to Program Devices ... 12 3.4 Using Learning Function to Customize SRC-3000b ... 15 3.4.1 Before Using Learning Function ... 15 3.4.2 Learning from Another Remote Control... 15 3.4.3 Deleting Key Codes and Device Codes...
Page 4
3.6.1 Creating a Macro ... 22 3.6.2 An example to create a Macro ... 24 3.6.3 Macro Interruption... 26 3.6.4 Viewing the Macro Key ... 26 Chapter 4 Miscellaneous Settings...27 4.1 Using the Transmission Function... 27 4.2 Setting the Backlight ... 29 4.2.1 Setting the Backlight...
NOTE: This manual helps you to learn how to use the advanced features of the SRC-3000b. However, it does not explain how to use the functions of your devices. Please refer to the user’s manuals of your devices for further information.
User-programmable keys for each device, up to 56 keys in total Automatic shutoff after 90 seconds of inactivity 1.2 Unpacking the SRC-3000b After unpacking the SRC-3000b, please check out the contents to make sure that the following items are included. 1. SRC-3000b 2. User’s Manual 3.
Point your original remote control to the learning eye and press the corresponding keys to send out the IR signals; so that the SRC-3000b can learn the IR codes for your devices. 1.3 Identifying Components 1. Infrared Eye 2. Light Sensor LCD Touch Screen 4.
This chapter provides the information helping you to use the SRC-3000b quickly. 2.1 Inserting the Batteries The SRC-3000b operates on three AAA alkaline batteries (not included in the package). Batteries must be inserted before you can operate the SRC-3000b. 1. Lift the battery cover.
2.1.2 Battery Tips and Precautions 1. The SRC-3000b will not lose programmed data when batteries are replaced. 2. Please always use fresh batteries. Alkaline batteries are recommended. Do not mix different types of batteries. 3. Ensure that positive (+) and negative (–) polarities of the batteries match the diagram inside the compartment.
The Touch Screen changes the number of soft keys according to the device that is selected. 2.2.1 Turning the Touch Screen On Turn on the SRC-3000b by touching the screen. The SRC- 3000b turns itself off after 90 seconds of inactivity. 2.2.2 Touch Screen Precautions Please review the following information carefully before using the SRC-3000b.
Macros. You will hear a beep when you press a key. To turn on or off the beep, please refer to page 31. Besides, the SRC-3000b turns itself off after 90 seconds of inactivity.
Page 12
SRC-3000B User’s Manual The following table provides an overview of major key functions. Name & Key Icon Device keys Device setting and LCD layout Code Setup key Setup device code, manually, automatically or by learning function Macro key Setup Macro...
Chapter 3 Setting Up the SRC- 3000b Before the SRC-3000b can be used to control a device, it needs to be configured to display your existing remote control keys and it must be programmed to send the correct infrared signals.
Page 14
SRC-3000B User’s Manual Select a key you want to modify. Press that key repeatedly to scroll through the available icons for the key. NOTE: You can press the available icons. Repeat step 3 to modify all desired keys. After finishing customizing...
Learning Function, to get the right codes for your target devices. Pre-Code You may configure all keys on SRC-3000b by entering a specific four-digit code number. This may be the fastest way to program the SRC-3000b. To get the specific code number, please refer to the supplied pre-programmed code list.
SRC-3000B User’s Manual 3.3 Using Pre-programmed Code to Program Devices You can follow these instructions to program a device by using pre-programmed codes. There are two ways for you to collect the right codes within the function: A. Manually Programming remote by Code.
Page 17
Example: You have two different TVs, TV1 and TV2. And you want to integrate the two TVs in SRC-3000b. 1. Please load the codes for TV1 by entering the four-digit code number for the TV deice. 2. You can select another device (for example, DVD) and load the codes for TV2 by entering the four–digit code...
Page 18
SRC- 3000b to the target device. Press to start Auto Search Function. SRC-3000b will send out IR codes to find the correct ones. When the target device is turned off, touch any part of the screen immediately to stop the searching.
System setup key can be learned. 3.4.2 Learning from Another Remote Control Please put the original remote and SRC-3000b on a flat surface. And then have the original remote pointed to the learning eye of SRC-3000b. The distance between two...
Page 20
SRC-3000B User’s Manual Select a device you want to program. Press and hold seconds to enter the confirmation screen. Press each number button (2, 4, 6, 8) in any order until they disappear and start to use the function. Press...
Page 21
3.4 Using Learning Function to Customize SRC-3000b Have your original remote pointed to “Learning Eye” at the bottom of SRC-3000b. The blinking key denotes the key to be learned. To make SRC-3000b to get the code for the key, please press the...
Page 22
SRC-3000B User’s Manual NOTES: a. Although SRC-3000b will guide you to learn each key, you can also select any key to learn as you want by touching it directly. You can also change the page by touching the device key.
3.4 Using Learning Function to Customize SRC-3000b 3.4.3 Deleting Key Codes and Device Codes You can follow these instructions to delete a code in a single key or all the codes in a device. Press and hold the for 3 seconds to enter the confirmation screen.
SRC-3000B User’s Manual 3.5 Resetting the SRC-3000b to Factory Defaults This function enables you to reset the SRC-3000b to the factory default configuration. NOTE: All Macros and programmed keys will be deleted when you reset the SRC-3000b to factory defaults.
Page 25
3.5 Resetting the SRC-3000b to Factory Defaults icon appears briefly on the screen to tell that SRC-3000b returns factory defaults.
SRC-3000B User’s Manual 3.6 Macro Function A Macro includes a series of commands. Macro function enables you to initiate a sequence of up to 60 commands just with a single key. You can use any key as your Macro key and insert time delays into the sequence. However, please remember that it will disable the original key function when you use the key as your Macro key.
Page 27
NOTE: If you select a key that already has been used as a Macro key, the new setting will replace the old Macro setting. Press any key as the commands saved in the Macro key. NOTES: a. You can choose any key in any device.
SRC-3000B User’s Manual 3.6.2 An example to create a Macro The following example will help you better understand creating a Macro sequence. It is provided to teach you how to create a Macro. By no means it is the only Macro sequence you can create.
Page 29
5. Press to switch to the DVD device menu so you can construct a series of commands for the DVD player. 6. Press (You may need to set a time delay between turning on the DVD player and playing a DVD.) 7.
SRC-3000B User’s Manual 3.6.3 Macro Interruption After pressing the preset Macro key for a device, you can interrupt the command sequence by pressing then appears and the macro stops. 3.6.4 Viewing the Macro Key You can view which keys are used as Macros for any particular device.
This chapter will tell you how to use transmission function, setup the backlight, and adjust the beep. 4.1 Using the Transmission Function The SRC-3000b can transmit customized data to another SRC-3000b. NOTE: Before using this function to transfer data, you must connect two SRC-3000b with SLC-2080 USB cable (optional accessory).
Page 32
You can press cancel the transmission. NOTES: Before transferring the data, please pay attention to 3 points: a. The two SRC-3000b remote controls have fresh batteries. b. These remotes are turned on. c. These remotes are connected by the USB cable.
4.2 Setting the Backlight 4.2.1 Setting the Backlight Press and hold seconds to enter the confirmation screen. Press each number button (2, 4, 6, 8) in any order until they disappear and start to use the function. Press . And then press t he key to start the setting.
The more frames you select, the more sensitively the backlight reacts to the ambient lighting. b. The light sensor sensitivity ranges from 1to 8. c. When you touch the LCD, the SRC-3000b activates the backlight automatically according to the environment.
4.3 Turning Off the Beep Signal Press and hold seconds to enter the confirmation screen. Press each number button (2, 4, 6, 8) in any order until they disappear and start to use the function. Press icon . And then press to start the setting.
This chapter assumes you have already set up the SRC- 3000b and saved all the IR codes for the keys. You can refer to Chapter 3 Setting Up the SRC-3000b on page 9 for more information about how to get the IR codes.
• The commands included in a Macro key will be shown on the LCD while the Macro key is working. • Backlight works automatically according to the environment • Automatic Power Saving Function • Motion detector to turn on SRC-3000b automatically Battery low indicator • Functions...
SRC-3000B User’s Manual Specifications Model Dimensions (WxHxD) Weight (without Batteries) Number of Device Keys Backlighting Learning Frequency Memory Batteries Power Consumption Operating Distance Interface IR Distance LCD Screen (W*H) SRC-3000b 3.1 x 7.5 x 1.25 inches (7.9 x 19 x 3.2 cm)
Appendix B Accessories SLC-2080 USB cable The SLC-2080 USB cable is an optional USB cable that transfers the data between two SRC-3000b. All settings including MCU firmware, settings in the flash memory and pre-programmed transmission “Miscellaneous Settings.” By connecting a transmit wire between two SRC-3000bs, you can also duplicate settings and functions from one SRC-3000b to another.
(page 4) 2. Check that the batteries are properly installed. 1. Make sure that the desired device key on the SRC-3000b LCD panel has been selected. 2. Move closer to the device. The maximum operating distance is approximately 30 feet.
Page 41
1. As a safety feature on the SRC- 3000b, you must press the REC key for two seconds. 1. Be sure to aim the SRC-3000b at the devices while the Macro commands are being sent. 2. Macro was not properly set up.
Page 42
The LCD screen turns off. Solution 1. Replace batteries in the SRC-3000b and the remote you are trying to configure. 2. Keep the distance between the remote control and the SRC- 3000b’s learning eye to about 2~4 inches.