Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Sunfire OLE-2SF
-
Page 2: Important Safety Instructions
Important Safety Instructions 1. Read Instructions 2. Keep these Instructions 3. Heed all Warnings. 4. Follow all Instructions 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. -
Page 3: Table Of Contents
Connectors/Pinout ... 1 System Connections ... 16 Programming ... 18 Feature Enable/Disable ... 19 Specifications ... 0 Troubleshooting ... 1 Warranty ... 3 Service Assistance ... 3 For more information on this and other Sunfire products, please visit our website: www.sunfire.com... -
Page 4: Introduction
Introduction The Olé -SF Film Interactive ® Touchpad (FIT) is a revolutionary in-wall controller for your Sunfire receiver or processor. Using a photographic film overlay instead of hard buttons, it marries the beauty of a touchscreen with the simplicity of a keypad –seamlessly controlling all major functions of your home theater or secondary room. - Page 5 1. If a problem persists, please contact your nearest authorized Sunfire Dealer. Please take a moment to fill out and mail the Sunfire Customer Re- sponse card. Also record the serial number and your details here: Serial Number: Purchased from:...
- Page 6 (Sunfire does not recommend wrapping the removable frame with wallpaper as this can cause the aforementioned symptom). Too much force on the front of the...
-
Page 7: Features
Features Top Panel 1. Mounting Screw (x 4) Use these screws to mount the touchpad into a standard 3 cu in. double-gang electrical box. . Program Button This button is for future use. 3. Light Sensor When this sensor is enabled, the Olé-SF backlight will brighten or dim depending on the room's ambient light conditions. - Page 8 Touchpad display . Power Turns system audio on and off. 6. System Bass/Treble control and other system options. 7. Home This toggles between the main source selection screen and the current source control. 8. Source selection View/change the source selection pages.
-
Page 9: Rear Panel
Rear Panel 14. Z•NET/VIA!NET Switch You must set this switch to VIA!NET for use with Sunfire receivers and processors. 1. System RJ-4 Jack Connect this jack with Cat- cable to the TP1 or TP RJ-4 con- nectors on the rear panel of your Sunfire receiver or processor. -
Page 10: System Design, Installation And Connections
Before installing the Olé-SF, it is essential to have a detailed and ac- curate system design. An authorized Sunfire installer should be con- tracted for proper installation and programming of your touchpad. The first step to a good design is to map the system. - Page 11 Sunlight can flood the IR receiver and make the system inoperative. Do not mount touchpads outdoors! Corrosion will damage them. Sunfire does not warrant Olé touchpads for outdoor use. Mounting Height The Olé-SF has no viewing...
-
Page 12: Connectors/Pinout
Local interface port. Sunfire TGR-401 Theater Grand Receiver RJ-4 Connector Use Cat- cable to connect the Olé-2SF to a Sunfire receiver or pro- cessor. The Sunfire standard pinout configuration is shown below. - Page 13 Local IR Interface Port Use this connector when utilizing the Olé-SF’s local control features, such as local source control, local IR sensors, or sense-enabled auto- mated sequences. Warning: The connection labeled “+1 Volts Out” is a voltage output. Do not con- nect a power supply to this connection! Controlling a single local device...
- Page 14 Local IR Input The Local IR-RECEIVER IN is typically used to connect an external IR sensor to the touchpad. Typical applications include a plasma- friendly IR sensor placed near a TV, or an auxiliary IR sensor placed in an area more convenient than the location of the touchpad.
- Page 15 Local Sense In The LOCAL SENSE IN port allows a contact-closure to trigger IR se- quences programmed into the Olé- SF using SunTools. Use a motion sensor to activate a contact-closure and cause automated actions such as system power on, drapes closed, and lights dimmed, for example.
-
Page 16: System Connections
(with metadata feedback) • Adjust Zone bass and treble ZONE 2 Olé-2SF NOTE: The two TP (touchpad) ports on your Sunfire receiver or processor are identical. All programming is stored in the Olé-2SF, so to reconfigure your Olé-SF to control the main zone, or... - Page 17 Home Theater Control (PC required) The Olé-SF is perfectly suited as an in-wall Home Theater controller. You may want to include one by the entrance to startup or shutdown the system. In this case, you will need to connect your Olé-SF to a PC running SunTools to reconfigure it to control the main zone.
-
Page 18: Programming
Programming The Olé-SF must be pro- grammed with Sunfire’s SunTools setup software using a PC running Windows XP. Downloads are facili- tated through the USB download port on the front of the unit. Note: A standard USB-A to USB- mini-B cable must be utilized for programming and is not included with the Olé-SF. -
Page 19: Feature Enable/Disable
Feature Enable/Disable: Speaker The Olé-SF contains a small speaker that allows audible feed- back signals to be heard as a result of button pushes. This feature can be disabled in the SunTools setup software. IR Sensor The Olé-SF features a built-in IR Sensor. -
Page 20: Specifications
Weight 14 oz./0.4kg Shipping Weight 16 oz./0.4kg © 008 Sunfire, LLC. All rights reserved. Sunfire, LLC re- serves the right to improve its products at any time. Therefore, specifications are subject to change without notice. Manual 913-144-00 Rev A... -
Page 21: Troubleshooting
Troubleshooting Power Symptom Cause Olé-SF 1. RJ-4 plug does not crimped incorrectly; power up. or wiring pinout of RJ-4 reversed. . Break in Cat- between Zone and “Head-End”. 3. Receiver or processor power is disconnected. Solution Verify wiring pinout and RJ-4 crimp. - Page 22 Symptom No control of IR sources. Intermit- tent source control. Cause 1. Programming: missing or incorrect IR commands. . Wiring: Incorrect wiring between Zone and ‘Head-End”. 3. Wiring: IR emitter connected to wrong source IR port of multi-room controller. IR emitter defective. IR flooding.
-
Page 23: Warranty
Sunfire Warranty Sunfire, LLC is proud of its products that have been built with care using advanced technology and premium component parts. Your unit has been crafted to perform properly for many years. Sunfire offers the following Warranty to you, the owner of a new Sunfire product: The Sunfire Warranty for the Olé-SF... - Page 24 Manual 913-144-00 Rev A...