NEC Aspire Series Networking Manual page 54

Features
ARS/F-Route
44 ◆
➻
26-02-02 : Dial Analysis Table for ARS - Service Type
For each Dial Analysis Table (1-200), select '0' for no ARS, '1' for Service Type 1 - Route to
Trunk Group Number to have the number route to a trunk group [Refer to Program 26-02-03]
or '2' for Service Type 2 - F-Route Selected to have the dialed number controlled by the F-
Route table. If Service Type 2 is selected and F-Route operation is on, the F-Route table used
is determined by Program 44-04. If F-Route operation is off, the routing is determined by Pro-
gram 44-05.
➻
26-02-03 : Dial Analysis Table for ARS - Additional Data / Service Number
For each Dial Analysis Table (1-200), if Service Type 1 was selected in Program 26-02-02,
enter the trunk group number (0-100, 0=no route).
➻
26-03-01 : ARS Dial Treatments
Assign the Dial Treatments (1-15) for automatic ARS dialing translation. Assign Dial Treat-
ments to Service Numbers (Trunk Groups) in Program 26-02. The ARS Dial Treatment
options are:
● 3 - Delete the NPA if dialed as part of the initial call. This requires at least 8 digits in the
ARS table (Program 26-02-01).
● 2 - Delete the leading digit if dialed as part of the initial call. This requires at least 8 digits
in the ARS table (Program 26-02-01).
● 1 - Add a leading 1 if not dialed as part of the initial call. This requires at least 8 digits in
the ARS table (Program 26-02-01).
● INPA - Insert the NPA speciÞed by NPA.
● DNN - Outdial the NN number of digits or execute the code that follows. For example,
D041234 out-dials 124. Valid entries are 0-9, #, *, Wnn (wait nn seconds) and P (pause).
Each digits code counts as a digit. So for example, if a P was added for a pause, the entry
would look like: D05P1234. This Dial Treatment can only be added from telephone pro-
gramming.
● Wnn - Wait nn seconds.
●
P - Pause in analog trunk.
● R - Redial the initially dialed number, including any modiÞcations
● E - End of Dial Treatment. All Dial Treatments must end with the E code.
● X - When ARS is enabled, X must be entered in the Dial Treatment in order for the system to
output the extension number of the call's originator to the black box for the E911 feature.
● An - Alternate Carrier Access (n = 1 ~ 4). The numeric digit instructs the system to insert
a Transit Network Selection information element in the SETUP message and also identi-
Þes which code in Program 26-11 will be included in the information element.
➻
44-01-01 : System Options for ARS/F-Route - ARS/F-Route Time Schedule
Set this option to '0' so that the F-Route table selected is determined only by the digits dialed
without any relation to the day or time of the call.
➻
44-02-01 : Dial Analysis Table for ARS/F-Route Access - Dial
Set the number of digits to be analyzed by the system for ARS routing. Using the 4-digit
extension number example in Program 11-01-01, the entry would be: Analysis Table 1:
720@@; Analysis Table 2: 723@@.
➻
44-02-02 : Dial Analysis Table for ARS/F-Route Access - Service Type
Select the Service Type (0=no setting, 1=extension call, 2=ARS/F-Route table, 3=Dial extension
analyze table). Using the 4-digit extension number example in Program 11-01-01, the entry would
be: Analysis Table 1: 2 (ARS/F-Route table); Analysis Table 2: 2 (ARS/F-Route table).
➻
44-02-03 : Dial Analysis Table for ARS/F-Route Access - Additional Data
Enter the additional data required for the service type selected in Program 44-02-02, either the
number of digits to be deleted or the table number to be used. Using the 4-digit extension
number example in Program 11-01-01, the entry would be: 1 (delete 1 digit).
➻
44-02-04 : Dial Analysis Table for ARS/F-Route Access - Dial Tone Simulation
If enabled (1), this option sends dial tone to the calling party once the routing is determined.
This may be required if the central ofÞce at the destination does not send dial tone. Using the
4-digit extension number example in Program 11-01-01, the entry would be: 0 (disabled).
Networking