Advertisement
Advertisement
Related Manuals for Sub-Zero Freezer
Summary of Contents for Sub-Zero Freezer
- Page 1 U I L T E F R I G E R A T I O N NSTALLATION NSTRUCTIONS...
-
Page 2: Table Of Contents
Check our website, subzero.com, for the most up-to-date specifications. ® SUB-ZERO is a registered trademark of Sub-Zero Freezer Company, Inc. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment. -
Page 3: Installation Recommendations
I N S TA L L AT I O N R E C O M M E N D AT I O N S The importance of the installation of the Sub-Zero Built-In unit cannot be overempha- sized. Installation should be done by a qualified installer. -
Page 4: Installation Specifications
I N S TA L L AT I O N Make sure that the actual equipment that was shipped to you matches the design you are expecting to install. The Sub-Zero Built-In line offers the following design alternatives— framed, overlay and stainless steel models. - Page 5 I N S TA L L A T I O N S P E C I F I C AT I O N S O V E R A L L D I M E N S I O N S All Refrigerator | All Freezer Models 73"...
- Page 6 B U I LT- I N O V E R A L L D I M E N S I O N S Over-and-Under Models O V E R - A N D - U N D E R Model 611 Model 611G with Glass Door Model 650...
- Page 7 B U I LT- I N I N S TA L L A T I O N S P E C I F I C AT I O N S O V E R A L L D I M E N S I O N S Side-by-Side Models 36"...
-
Page 8: Installation Instructions
A separate circuit, servicing only this appliance, is required. All Sub-Zero Built-In models are equipped with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating 3-prong grounding-type wall receptacle. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. - Page 9 B U I LT- I N I N S TA L L A T I O N I N S T R U C T I O N S U N PAC K T H E U N I T Uncrate the unit, remove its wood base and discard the shipping bolts that hold the wood base to the bottom of the unit.
- Page 10 B U I LT- I N A N T I - T I P To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking device. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1"...
- Page 11 B U I LT- I N I N S TA L L A T I O N I N S T R U C T I O N S WAT E R L I N E C O N N E C T I O N To connect the ice maker water line, remove "...
-
Page 12: Framed Panel Installation
If your customer has ordered either a framed or overlay model, you will be installing panels to give the unit the custom Sub-Zero look. I N S TA L L A T I O N F R A M E D... - Page 13 I N S TA L L A T I O N With a Phillips screwdriver, remove the handles from the freezer and refrigerator doors. Slide the panel into the frame on the door. With the panel in position, replace the handles.
- Page 14 S P E C I F I C AT I O N S F R A M E D D O O R P A N E L S All Refrigerator | All Freezer Framed (F) Models Model 601R Refrigerator Framed Panel Raised Panel Handle Recess Location –...
- Page 15 F R A M E D D O O R P A N E L S Side-by-Side Framed (F) Models Model 661 Refrigerator Framed Panel Freezer Framed Panel Raised Panel Handle Recess Location – Refrigerator | Freezer Panel Model 642 Refrigerator Framed Panel 24" (610) Freezer Framed Panel Raised Panel Handle Recess Location –...
-
Page 16: Overlay Panel Installation
The door channel is now ready to accept the overlay panel assembly. Sub-Zero allows a backing material into place in the frame. If your material is thicker than a rout an edge around the panel to get a proper... - Page 17 Sub-Zero unit. " (6) to a P A N E L S P A N E L...
- Page 18 S P E C I F I C AT I O N S O V E R L AY D O O R P A N E L S All Refrigerator | All Freezer Overlay (O) Models Model 601R Refrigerator Overlay Panel...
- Page 19 O V E R L AY D O O R P A N E L S Side-by-Side Overlay (O) Models Model 661 Refrigerator Overlay Panel Refrigerator Spacer Panel Refrigerator Backer Panel Freezer Overlay Panel Freezer Spacer Panel 14" (356) Freezer Backer Panel Model 642 Refrigerator Overlay Panel...
- Page 20 S I D E PA N E L I N S TA L L AT I O N O P T I O N S 1/4" (6) THICK SIDE PANEL FITTED IN TO UNIT FRAME DOOR PAN HEAD SCREW 1/8" (3) THICK BATTENS SIDE OF SUB-ZERO UNIT FRAME 1/4" (6) SIDE PANEL MATERIAL " (616) 1/4"...
- Page 21 This will assure a proper fit and a secure installation. The Sub-Zero Anchoring Kit (part #4200900), available from your Sub-Zero dealer, includes the necessary hardware.
- Page 22 The doors of all Built-In models open to 130 degrees. For Models 601R, 601RG, 601F, 661, 642, 685, 632 and 695, optional 90˚ or 105˚ door stop kits are available through your Sub-Zero dealer. Models 611, 611G, 650 and 650G come with a door stop pin to limit the door swing to 90 degrees.
- Page 23 60-day parts and labor warranty for cosmetic defects. The information and images in this book are the copyright property of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero Freezer Company, Inc.
- Page 24 S U B - Z E R O F R E E Z E R C O M PA N Y, I N C . P. O . B O X 4 4 1 3 0 M A D I S O N , W I 5 3 7 4 4 - 4 1 3 0 8 0 0 - 2 2 2 - 7 8 2 0 S U B Z E R O .