Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Keysight Technologies 81960A
Summary of Contents for Keysight Technologies 81960A
- Page 1 Keysight 81960A Compact Tunable Laser Source Module Getting Started Guide...
- Page 2 AND ANY INFORMATION CONTAINED ment (EULA), a copy of which can be found HEREIN, INCLUDING BUT NOT LIMITED TO at http://www.keysight.com/find/sweula. THE IMPLIED WARRANTIES OF The license set forth in the EULA represents Keysight 81960A Compact TLS Module Getting Started Guide...
-
Page 3: Table Of Contents
Laser class 1M label Introduction What is a Tunable Laser Source? Installation Front Panels Front Panel Controls and Indicators Typical Use Models Optical Output Polarization Maintaining Fiber Angled and Straight Contact Connectors Keysight 81960A Compact TLS Module Getting Started Guide... -
Page 5: Getting Started
Keysight 81960A Compact Tunable Laser Source Module Getting Stared Guide Getting Started This chapter provides a general description of Keysight 81960A Tunable Laser Source Family. Safety Considerations Initial Safety Information for Tunable Laser Modules / 10 Laser Safety Labels / 11... -
Page 6: Safety Considerations
Keysight Technologies assumes no liability for the customer’s failure to comply with these requirements. Before operation, review the instrument and manual, including the red safety page, for safety markings and instructions. -
Page 7: Initial Inspection
Storage and Shipment A Keysight 81960A Compact Tunable Laser Source module can be stored or shipped at temperatures between - 40°C and + 70°C. Protect the module from temperature extremes that may cause condensation within it. -
Page 8: Protecting Empty Module Slots
Figure 1 Fitting a Blind Panel Push the top of the blind panel so that it clicks into position. To remove a blind panel, pull the handle. NOTE Keysight 81960A Compact TLS Module Getting Started Guide... -
Page 9: Fitting A Filler Module For Back-Loadable Module Slots
Getting Started Fitting a Filler Module for Back-Loadable Module Slots The Keysight 81960A Filler Module must be used if you have not installed a back-loadable Tunable Laser module into the 8164A/B Lightwave Measurement System. The Keysight 81960A Filler Module can be fitted and removed in the same way as any back-loadable module. -
Page 10: Initial Safety Information For Tunable Laser Modules
* Max. CW output power is defined as the highest possible optical power that the laser source can produce at its output connector. ** Max. permissible CW output power is the highest optical power that is permitted within the appropriate laser class Keysight 81960A Compact TLS Module Getting Started Guide... -
Page 11: Laser Safety Labels
• Refer servicing only to qualified and authorized personnel. The built in laser diode is active whenever the instrument is powered on, CAUTION therefore disabling the output is not sufficient to establish eye safe conditions. Keysight 81960A Compact TLS Module Getting Started Guide... - Page 12 Getting Started The remote interlock function interrupts the laser current when the NOTE connector is open. Keysight 81960A Compact TLS Module Getting Started Guide...
-
Page 13: Introduction
What is a Tunable Laser Source? A Tunable Laser Source (TLS) is a laser source for which the wavelength can be varied through a specified range. The Keysight 81960A is a TLS with continuous-sweep measurement capabilities, where wavelength and power are regulated while the laser changes wavelength at a constant rate. -
Page 14: Front Panels
When the active LED is not lit the output is disabled. The built-in laser diode is active whenever the instrument is powered on, CAUTION therefore disabling the output is not sufficient to establish eye safe conditions. Keysight 81960A Compact TLS Module Getting Started Guide... -
Page 15: Typical Use Models
Getting Started Typical Use Models The Keysight 81960A Tunable Laser Source Family provides high output power up to +14 dBm. This module covers a total wavelength range of 125 nm in the C- and L-band. This laser has been designed for making spectral measurements of passive fiber optic components, where results with high wavelength accuracy and dynamic range are needed. -
Page 16: Optical Output
For further details on connector interfaces and accessories, refer to the 81960A User’s Guide. Angled and Straight Contact Connectors To ensure most accurate measurements, the Keysight 81960A Fast sweeping Compact TLS module is equipped with angled contact connectors. Keysight 81960A Compact TLS Module Getting Started Guide... - Page 17 Angled non-contact fiber end connectors with orange sleeves cannot be NOTE directly connected to the instrument. For further details on connector interfaces and accessories, refer to the 81960A User’s Guide. Keysight 81960A Compact TLS Module Getting Started Guide...
- Page 18 This information is subject to change without notice. © Keysight Technologies 2017 Edition 4.0, July 2017 Printed in Malaysia www.keysight.com...
Need help?
Do you have a question about the 81960A and is the answer not in the manual?
Questions and answers