Error Code Indication - Bosch Perfomance Series Original Instructions Manual

Drive unit & ebike battery chargers
Table of Contents

Advertisement

Available languages

Available languages

English–9
Setting the Assistance Level
On the operating unit 11 you can set how much the eBike
drive assists you while pedalling. The assistance level can be
changed at any time, even while cycling.
Note: For individual versions, it is possible that the assistance
level is pre-set and cannot be changed. It is also possible that
less assistance levels are available for selection than listed here.
The following assistance levels (max.) are available:
– "OFF": The motor assistance is switched off, and the eBike
can be moved as a normal bicycle only by pedalling. The
push assistance/start assistance cannot be activated in
this assistance level.
– "ECO": Effective assistance at maximum efficiency for
maximum cruising range
– "TOUR": Uniform assistance, for touring with long cruising
range
– "SPORT": Powerful assistance for sportive riding off road
as well as for urban traffic
– "TURBO": Maximum assistance, supporting highest ca-
dence for sportive riding
To increase the assistance level, press the "+" 15 button on
the operating unit until the desired assistance level appears in
the display r5. To decrease the assistance level, press the
button"–" 14.
The requested motor output is displayed in indicator r4. The
maximum motor output depends on the selected assistance
level.
Assistance Level
"ECO"
"TOUR"
"SPORT"
"TURBO"
* The motor output can vary for individual versions.

Error Code Indication

The components of the eBike system are continuously and au-
tomatically monitored. If an error is detected, the respective
error code is indicated on the on-board computer.
Depending on the type of error, the drive unit is automatically
shut off, if required. Continued travel without assistance from
Code
Cause
410
One or more buttons of the on-board
computer are blocked.
414
Connection problem of the operating
unit
418
One or more buttons of the operating
unit are blocked.
422
Connection problem of the drive unit Have connections and contacts checked.
0 276 001 SPN | (3.7.15)
Assistance Factor*
(Derailleur)
Cruise
Speed
50%
55%
50%
120%
120%
120%
190%
190%
210%
275%
275%
300%
When the on-board computer is removed from the holder 4,
the last indicated assistance level is stored; the motor-output
indicator r4 remains empty.
Switching the Push/Start Aid On/Off
With the speed version, the push aid can also be used as a
start aid. The start aid is switched off at 18 km/h.
The push/start aid can make it easier for you to push or start
the eBike. The speed of this feature depends on the selected
gear and depending on the model, can reach a maximum of
6 km/h or 18 km/h. The lower the selected gear, the lower the
speed of this function (at full capacity).
The push/start aid function may only be used when
pushing or starting the eBike. If the wheels of the eBike
have no contact with the ground when using the push aid,
then there is risk of injury.
To switch on the push/start aid, press and hold the "WALK"
16 button on the operating unit. The eBike drive is switched
on.
The push/start aid is switched off if one of the following oc-
curs:
– you release the "WALK" 16 button,
– the wheels of the eBike are blocked (e.g. by actuating the
brakes or impacting against an obstacle),
– the speed exceeds 6/18 km/h.
Switching bike lights on/off
In the model, in which the lighting is powered by the eBike
system, the front and rear light can be switched on and off at
the same time via the on-board computer with the button 6.
The illumination symbol s1 is displayed when the light is on.
CX
Switching the bike light on and off has no effect on the back
lighting of the display.
the drive unit is possible at any time. However, have the eBike
checked before attempting new trips.
Have all repairs performed only by an authorised bike
dealer.
Corrective Measure
Check if any buttons are blocked, e.g. from dirt or debris. Clean the
buttons, if required.
Have connections and contacts checked.. Contact your Bosch eBike
dealer.
Check if any buttons are blocked, e.g. from dirt or debris. Clean the
buttons, if required.
Bosch eBike Systems

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents