Stamina 55-1772 Owner's Manual

Stamina 55-1772 Owner's Manual

Stamina magnetic cross trainer elliptical owner's manual

Advertisement

CAUTION:
Weight on this product should not exceed 250 lbs.
2008, 07
This Product is Produced Exclusively by
2040 N. Alliance, Springfield, MO 65803
Customer Service
1 (800) 375-7520
www.staminaproducts.com
Owner's
Manual
WARNING
Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.
When calling for parts or
service, please specify the
following number.
Model#: 55-1772
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
2008 Stamina Products, Inc.

Advertisement

Table of Contents
loading

Summary of Contents for Stamina 55-1772

  • Page 1 Follow all safety instructions in this manual. When calling for parts or service, please specify the following number. Model#: 55-1772 STAMINA PRODUCTS MADE IN CHINA Product May Vary Slightly From Pictured. 2008 Stamina Products, Inc.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Safety Instructions Before You Begin Equipment Warning & Notice Labels Hardware Identification Chart Assembly Instructions Set Up Instructions Operational Instructions Storage SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following Safety Instructions before using the Magnetic 1772 Elliptical.
  • Page 3 Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time. Friday, 8:00 A.M. - 3:00 P.M., Central Time. TELEPHONE ONLINE MAIL CUSTOMER SERVICE CUSTOMER SERVICE CUSTOMER SERVICE STAMINA PRODUCTS, INC. Tel: 1 (800) 375-7520 Fax: (417) 889-8064 customerservice@staminaproducts.com ATTN: Customer Service www.staminaproducts.com P.O. Box 1071 Springfield, MO. 65801-1071...
  • Page 4: Before You Begin

    BEFORE YOU BEGIN Thank you for choosing the Magnetic 1772 Elliptical. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest. It's a proven fact that a regular exercise program can improve your physical and mental health.
  • Page 5: Equipment Warning & Notice Labels

    EQUIPMENT WARNING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Magnetic 1772 Elliptical. Please take a moment to familiarize yourself with all of the warning & notice labels. Label is larger than actual size WARNING LABEL(91)
  • Page 6: Hardware Identification Chart

    HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.
  • Page 7: Assembly Instructions

    ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed.
  • Page 8 ASSEMBLY INSTRUCTIONS Metal Fitting Cable End Bracket Spring Hook STEP 3 Refer to the inset drawing. Lay the UPRIGHT(6) on the floor close to the front of the MAIN FRAME(1). Set the TENSION KNOB(25) on the UPRIGHT(6) at position 8, so the CABLE END of the TENSION KNOB KNOB(25) extends out of the metal fitting as far as possible.
  • Page 9 ASSEMBLY INSTRUCTIONS LEFT STEP 6 There is an "L" decal on the LEFT PEDAL ARM(4), and an "R" decal on the RIGHT PEDAL NOTE: ARM(5). The RIGHT PEDAL SHAFT(42) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL SHAFT(41) has left hand threads and is tightened by turning counterclockwise. Place the front end of the RIGHT PEDAL ARM(5) on the ROLLER(58) of the FRONT STABILIZER(2).
  • Page 10 ASSEMBLY INSTRUCTIONS LEFT Look down from the top Pivot Tube Shaft Pivot Tube RIGHT STEP 8: There is an "L" decal on the LEFT HANDLEBAR(8), and an "R" decal on the RIGHT HANDLEBAR (9). To assemble the RIGHT HANDLEBAR(9), place a SPACER(51) and a LARGE WASHER(M16)(52) on the right side of the SHAFT on the UPRIGHT(6).
  • Page 11 ASSEMBLY INSTRUCTIONS Strap STEP 11 Refer to illustration A. Tie the STRAP to the plug end of the PULSE SENSOR WIRE(27). Pull the STRAP from the square hole on the top of the UPRIGHT(6) until the PULSE SENSOR WIRE(27) is pulled through and extends out of the square hole.
  • Page 12: Set Up Instructions

    SET UP INSTRUCTIONS Place the Magnetic 1772 Elliptical in the area where it will be used. It is recommended that the Magnetic 1772 Elliptical be placed on an equipment mat. The maximum operation dimensions of the Magnetic 1772 Elliptical are approximately 54 inches long x 59 1/2 inches tall x 24 3/8 inches wide. (These dimensions may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic 1772 Elliptical.
  • Page 13: Operational Instructions

    OPERATIONAL INSTRUCTIONS LOAD ADJUSTMENT To increase the load, turn the TENSION KNOB(25) clockwise. To decrease the load, turn the TENSION KNOB(25) counterclockwise. NOTE: The load will increase as you pedal faster. EXERCISE WORKOUT To start using the Magnetic 1772 Elliptical simply stand on the foot pedals with the front of your shoes close to the front edge of the pedal cap.
  • Page 14 USING THE METER POWER ON: Pedal movement or press any button. POWER OFF: Automatic shut off after 4 minutes of inactivity. Resets all values to zero. FUNCTION BUTTONS: MODE : Press and release to select each function for display on Upper Display or preset target values. Press the button and hold it down for three seconds to reset all functions to zero.
  • Page 15: Storage

    Adjust the TENSION KNOB(25) and verify that the Magnetic System provides tension. The Magnetic System should provide many years of use. Verify that the WARNING LABEL(91) is in place and easy to read. Call Stamina Products immediately at 1-800-375-7520 for a replacement WARNING LABEL(91) if it is missing or damaged.
  • Page 16: Conditioning Guidelines

    CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually by monitoring your heart rate while you exercise. Remember to follow these essentials: Have your doctor review your training and diet programs.
  • Page 17: Warm-Up And Cool-Down

    WARM-UP and COOL-DOWN Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength...
  • Page 18: Product Parts Drawing

    PRODUCT PARTS DRAWING FRONT Strap BACK...
  • Page 19: Parts List

    PARTS LIST PART# PART NAME Main Frame Front Stabilizer Rear Stabilizer Left Pedal Arm Right Pedal Arm Upright Stationary Handlebar Left Handlebar Right Handlebar Lower Pivoting Arm Linkage Pulley and Axle Bearing (6003Z) Bearing Washer (M17) C Ring (17mm) V-Ribbed Belt Idler Arm Idler Wheel ø...
  • Page 20 PARTS LIST PART# PART NAME Plastic Washer (M8 x ø18 x 2mm thick) Round Plug (28.6mm) Spacer Large Washer (M16 x ø32 x 0.5mm thick) Dome Plug (28.6mm) Foam Grip Short Foam Grip Round Plug (25.4mm) Round Plug (24.8mm) Roller Roller Spacer Wheel Leveling Cap...
  • Page 21: Warranty

    To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springfield Missouri, USA, 65801-1071, or email us at customerservice@staminaproducts.com, or call us at 1-800-375-7520.
  • Page 22: Notes

    NOTES...
  • Page 23: Fax/Mail Ordering Form

    PART # EXAMPLE: CUSTOMER SERVICE CUSTOMER SERVICE Fax: (417) 889-8064 customerservice@staminaproducts.com www.staminaproducts.com Detach and Mail or Fax the Form Below Stamina Products, Inc. P.O. Box 1071 Springfield, MO 65801-1071 State: Work Phone #: ( DESCRIPTION Rear Unit Assembly ONLINE MAIL STAMINA PRODUCTS, INC.

This manual is also suitable for:

1772

Table of Contents