Related Manuals for Spirit inspire IN839
Summary of Contents for Spirit inspire IN839
- Page 1 Z100 / Z300 Z500 Z700 OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW TREADMILL!
-
Page 2: Table Of Contents
Operation of Your New Treadmill……………………………………………………………. 9 Maintenance of Your New Treadmill…………………………………………………………11 Service Checklist - Diagnosis Guide…………………………………………………………13 Manufacturer’s Limited Warranty…………………………………………………………….. 14 ATTENTION- THIS TREADMILL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. IN839... -
Page 3: Product Registration
Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased this treadmill is your administrator for all Spirit warranty and service needs. -
Page 4: Important Safety Instructions
Important Safety Instructions WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock, disconnect your Spirit treadmill from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 120-volt, 20-amp grounded outlet. -
Page 5: Important Electrical Information
Whenever the adapter is used, it must be held in place by a metal screw. Grounded Outlet Adapter Metal Screw Tab of IN839 Grounding Screw... -
Page 6: Important Operation Instructions
NEVER mount or dismount the treadmill while the belt is moving. Spirit treadmills ● start at a very low speed and it is unnecessary to straddle the belt during start up. -
Page 7: Assembly Instructions
Stop / Pause switch in normal operation. Assembly Instructions (IN839) ASSEMBLY PACK CHECK LIST (IN839) 5/16"x 1/2" Button Head Socket Screw (x2) 5/16"x 3/4" Button Head Socket Screw (x2) 5/16"x 1-1/2" Button Head Socket Screw (x2) 5/16"x 19 x1.5T Curve Washer (x2) - Page 8 Install the console into the Console Support with 4 pcs of M5 x 10 mm Button Head Socket Screws by using the Combination M5 Allen Wrench & Screwdriver. (As shown in figure 5.) ■ PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED. Assembly Instructions (IN839) IN839...
-
Page 9: Folding Instructions
IN839 Folding Instructions Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. -
Page 10: Operation Of Your New Treadmill
Operation of Your Treadmill Getting familiar with the control panel ■ IN839 Console WINDOW DISPLAY: SPEED: Displays the current running speed from 0.8Mph- 6Mph. TIME: Accumulates total workout time from 00:00 to 99:59. DISTANCE: Accumulates total workout distance from 0.00 to 99.99 miles. -
Page 11: Console Operation
After setting, press “START” to start training. 5、 If after pressing “STOP” button to stop the treadmill, and you want to resume your workout, you can press “START” button again to start the treadmill then all previous data will resume counting. IN839... -
Page 12: Maintenance Of Your New Treadmill
6 mm Allen wrench provided in the parts package. The adjustment bolt is located at the end of the right side rail as noted in diagram below. Tracking Tension Adjustment Adjustment Side Only Side Only Note: Adjustment is thru small hole of end cap. IN839... -
Page 13: Treadbelt Tracking Adjustment
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY. BELT / DECK LUBRICATION: Do not re-lube with other than Spirit lubricant. Spirit provides one application with this unit. See your Spirit dealer for additional purchases. The use of some other lubricants may destroy the deck surface or belt and will void warranty. -
Page 14: Service Checklist - Diagnosis Guide
If an extension cord is required, it should be as short as possible and heavy duty 16 gauge minimum. Low household voltage. Contact an electrician or your Spirit dealer. A minimum of 110 volt AC current is required. High belt/deck friction. See General Maintenance section on lubrication. -
Page 15: Manufacturer's Limited Warranty
Manufacturer’s Limited Warranty Spirit Manufacturing Inc. warrants all its treadmills’ parts for a period of 2 years from the date of retail sale, as determined by sale receipt, or eighteen (18) months from the original factory shipping date, whichever comes first. Spirit’s responsibilities include providing new or remanufactured parts, at Spirit’s option, and technical support to our independent dealers and servicing organizations. - Page 16 Jonesboro, AR 72402-2037 Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Spirit Manufacturing, Inc. This warranty applies only in the 50 states of the U.S.A. and Canada. IN839 Series...