Download  Print this page

Technical Data; Noise/Vibration Information; For Your Safety - Bosch AKE 30-19 S Original Instructions Manual

Hide thumbs

Advertisement

OBJ_BUCH-1176-002.book Page 9 Wednesday, December 7, 2016 3:23 PM

Technical Data

Chain saw
Article number
Rated power input
Chain speed (no-load)
Blade length
Chain type
Drive link thickness
Amount of drive links
Oil reservoir capacity
Automatic chain oiler
Toolless chain tensioning (SDS)
Nose sprocket
Kickback brake
Run down brake
Metal gripping teeth
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below 0.25 ohm.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-13.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); sound power level
103 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-13:
2
2
a
=6.0 m/s
, K=1.5 m/s
.
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
AKE 30-19 S
AKE 35-19 S
3 600 H36 D..
3 600 H36 E..
W
1900
m/s
12
cm
30
3/8" – 90
mm
1.1 (0.043")
1.1 (0.043")
45
ml
200
kg
4.3
/II
Assembly

For Your Safety

 Warning! Switch off, remove plug from mains before
adjusting cleaning or if the cable is cut, damaged or en-
tangled.
 Caution! Do not touch the rotating chain.
 Do not operate the chain saw near other people, chil-
dren or animals. Do not operate the chain saw after
drinking alcohol or under the influence of intoxicating
drugs or medication.
Electrical Safety
Your power tool is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch Service Cen-
tre for details.
Only extension cables of design type H07 RN-F or IEC (60245
IEC 66) are permitted for use.
When operating the chain saw with an extension cable, the
following conductor cross-sections are required:
2
– 1.0 mm
: max. length 40 m
2
– 1.5 mm
: max. length 60 m
2
– 2.5 mm
: max. length 100 m
It is recommended for increased electrical safety to use a Re-
sidual Current Device (RCD) with a tripping current of not
more than 30 mA. Always check your RCD every time you use
it.
English | 9
AKE 40-19 S
3 600 H36 F..
1900
1900
12
12
35
40
3/8" – 90
3/8" – 90
1.1 (0.043")
52
57
200
200
4.4
4.5
/II
/II
F 016 L81 143 | (7.12.16)

Advertisement

loading

This manual is also suitable for:

Ake 35-19 sAke 40-19 s