Frames or parts under high stress may fail, causing you to lose control or fall. Because of the risk involved, Specialized recommends that you conduct a thorough inspection before each ride. If you miss a jump, ditch your bike in mid crash, dump or launch your bike without you on it, inspect yourself for injury, then carefully inspect your bicycle for damage.
Page 5
Specialized does not warrant the bicycle frame or components for such activities, and expressly disclaims all warranties, including the warranty of fitness for particular purpose and merchantability.
ENDURO SL FRAME GEOMETRY *Top Tube Length 9mm **Standover Hgt 74mm Head Tube Length Carbon 9mm Head Tube Length Alloy 0mm Wheelbase 060mm Chainstay Length 44mm * TT length is the Horizontal Measurement from the center-line of the HT at the top of the HT to the center-line of the projected seat tube. ** Stand Over height is measured vertically at the centerpoint of the TT measurement.
• Turn the knob counter-clockwise for faster rebound (higher speeds, small bumps, more traction. 3. Adjust compression: Specialized AFR shocks are equipped with a spike valve to optimize the shock’s compression. Low-speed compression (induced by rider’s body weight - pitching, diving) is adjustable by turning the blue knob.
Page 11
1. Setting air pressure and sag: • Use a high-pressure shock pump to add air. Sag is based on a % of stroke of fork. Set sag according to chart as a starting point, then adjust for preference, terrain and riding technique. Always perform adjustments with fork in long travel mode! Pressure increases in short travel. •...
DERAILLEUR GUARD INSTALLATION The Specialized Derailleur guard is available separately through your local Specialized dealer. The guard works with solid or Q/R axle types and is compatible with all Mountain bike models using the 00-006 Enduro/Demo derailleur hanger. Guard Part #: 9896-400...
DOWNTUBE CABLE GUIDE INSTALLATION The Specialized Enduro SL is equipped with bolt-on downtube cable guides. For proper housing placement and function, the hydraulic rear brake housing goes in the larger middle slot, the gear cables go on the outside. Do not overtighten the guide bolts.
Page 14
ENDURO SL CARBON INSTRUCTIONS The Specialized Enduro SL Carbon frame utilizes advanced composite materials that require particular care during assembly, storage and riding. This installation and care guide contains instructions and warnings, plus torque specifications. Assembling a complete bicycle is a complicated task requiring training and experience, only a trained and experienced bicycle mechanic should install components to this frame.
Page 15
Your Specialized frame does not require any Bottom Bracket or Head Tube pre-installation preparation. All surfaces are already prepared from the factory, with the exception of greasing the bottom bracket threads and head set cups. It is acceptable to chase the bottom bracket threads if necessary.
Page 16
Schematic #18 Seatstay tabs LINK ASSEMBLY All alloy spacers: Small diameter of spacer facing bearing Hanger bolt Dropout Hanger DROPOUT ASSEMBLY x 2 Link Chainstay Chainstay Bridge BOTTOM BRACKET ASSEMBLY UPPER SHOCK ASSEMBLY Frame Shock Mount LOWER SHOCK ASSEMBLY Bolts Derailleur Cage Derailleur Cage nut Derailleur Mount...
Page 17
NOTE: Bearing and Bolt Kits are available only through your local Specialized dealer. To retain your warranty and for your safety, all maintenance should be performed by your local Specialized dealer. 2007 Enduro SL Part # Qty. Part Description BB Pivot Bearing...
ADDITIONAL CONDITIONS This Limited Warranty is made only to the original owner of this new Specialized bicycle or frameset purchased from an authorized Specialized dealer, and it shall remain in force only as long as the original owner retains ownership of the Specialized bicycle. This Limited Warranty is not transferable. In order to exercise your rights under this limited warranty, the bicycle or frameset must be presented to an authorized Specialized dealer, together with a receipt, bill of sale or other appropriate written proof of purchase which identifies the bicycle or frameset by serial number.
Page 19
USEFUL PRODUCT LIFE CYCLE Every Specialized bicycle and frameset has a useful product life cycle. The length of that useful product life cycle will vary with the construction and materials of the bicycle or frameset, the maintenance and care the bicycle or frameset receives over its useful product life cycle, and the type and amount of use the bicycle or frameset is subject to. Uses in competitive events, trick riding, ramp riding, jumping, aggressive riding, riding on severe terrain, riding in severe climates, riding with heavy loads, commercial activities and other types of non-standard use can dramatically shorten the useful product life cycle of a Specialized bicycle or frameset.