Configuration within a Home or Office Network ...2 Package Contents...3 Front Panel of SOYO G668 IP phone...4 Rear Side of SOYO G668 IP phone ...6 INSTALLATION... 7 Installation with a Single Computer...7 Installation within a Home or Office Network ...9 CONFIGURATION VIA IP PHONE KEYPAD...
A cable modem Internet service from a cable television company Other high-speed Internet connection such as ISDN and T1 You can use G668 IP phone in your home or office network with any broadband DSL or Cable modem, Ethernet router, switch and your computer.
Please refer to the following configuration. Configuration within a Home or Office Network You can connect G668 IP phone to any router on a network with broadband Internet connection such as DSL, Cable or T1. SOYO G668 Ethernet IP Phone User Guide...
Package Contents Make sure the following contents are included in the G668 IP phone package: One SOYO G668 IP phone One DC 7.5V 0.45A Power Adapter User Manual One Ethernet RJ-45 Cable SOYO G668 IP phone User Manual SOYO G668 Ethernet IP Phone User Guide...
SOYO G668 Ethernet IP Phone User Guide Front Panel of SOYO G668 IP phone...
Page 7
Redial the last dialed phone number Speaker Press this key to make a call without lifting the handset Volume + Increase the volumes of handset or speaker; Volume - Decrease the volumes of handset or speaker; SOYO G668 Ethernet IP Phone User Guide...
2. Connect one end of another Ethernet RJ-45 cable to your computer, and connect the other end of the same cable to the LAN ports at the rear of the G668 IP phone. (This is an optional step. IP phone can work without the computer) 3.
Page 10
“Configuration for Static IP” section on page12. 8. If you still have problems logging on, please refer to “Troubleshooting” on page 20. If problem persist then contact your VoIP provider. SOYO G668 Ethernet IP Phone User Guide Booting … DHCP Connecting …...
2. Using another RJ-45 cable, you can connect one end of the Ethernet RJ-45 cable to your computer, and connect the other end to the LAN port at the rear of the G668 IP phone. (This is an optional step. IP phone can work without the computer) 3.
Page 12
Now you can pick up the hand set and start making phone calls. 6. If you still have problems logging on, please refer to “Troubleshooting” on page 20. If problem persist then contact your VoIP provider. SOYO G668 Ethernet IP Phone User Guide...
Configuration via IP Phone Keypad Configuration for DHCP (default) The SOYO-G668’s default setting is set on DHCP enabled. If you have a router with DHCP support, or if you connect the IP phone directly to the cable modem with dynamic IP address from the ISP, you don’t need to perform any of the following configurations.
Please have the static IP address, subnet mask, router address, and DNS address ready from your web administrator or ISP. Please make sure you have entered the “networking settings” before proceeding. SOYO G668 Ethernet IP Phone User Guide...
Page 15
Allow a few seconds for the system to boot the new configuration and you SOYO_Group are ready to make calls Warning Users are not allowed to change “protocol settings”, “phone settings”, or “audio settings” without proper guidance from the VoIP Service Providers or Carriers. SOYO G668 Ethernet IP Phone User Guide...
Set how IP phone gets relevant network parameters by selecting corresponding item from drop down list. static ip: Select this item to authorize users set IP address, subnet mask and router IP address of IP phone manually. SOYO G668 Ethernet IP Phone User Guide...
Note: Please check with your VoIP service provider for the protocol settings. Changing the settings without proper guidance may result the IP phone not functioning. nat traversal: NAT traversal method the IP phone uses. SOYO G668 Ethernet IP Phone User Guide...
Forward calls if power off by checking this box. fwd busy: Forward calls if busy by checking this box. answer: Enter a number from 0 through 60 to set the entries of the seconds before the phone forward the calls. SOYO G668 Ethernet IP Phone User Guide...
Then please input the password again to enter the set page and then click Save/Reboot button to confirm the modification. Address Book Click this button to open the following speed dial settings page. SOYO G668 Ethernet IP Phone User Guide...
Page 20
SOYO G668 Ethernet IP Phone User Guide In this page, you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name. For example, input “ Tom” in Name field following 001, and then input the number, 14081234567 into Phone number field.
Software Upgrading Users can upgrade SOYO G668 IP phone to the latest software version by the following procedure: make sure the upgrade address has been entered into the setting page correctly, then from keypad dial “Hand-free Speaker”, input “12348” and then press “Local IP”, the software of SOYO G668 IP phone will be automatically upgraded to the latest version.
IP phone hand set When I dial a phone number, I always hear fast busy tone. SOYO G668 Ethernet IP Phone User Guide SOLUTION Press Local IP button to find the IP address of your IP phone. If it shows 0.0.0.0, it means the Internet connection is down, please check the LAN cable and modem.
Page 23
I can make outbound calls, but I can not receive incoming calls LCD shows incorrect date and time If you have further questions, please contact SOYO Group Inc. technical support department by: Web: http://phone.soyo.com Email: phone@soyousa.com...
SOYO G668 Ethernet IP Phone User Guide Appendix: Port Forwarding Note: Try port forwarding only when you have router or firewall in your network and your IP phone do not function correctly. Applications running on TCP/IP open connections to other computers or Internet devices using something called ports.