Table of Contents
Advertisement
Quick Links
SERVICE
Soundstream RUBICON amplifier is protected
Your
Please read the enclosed warranty card for details.
Stereo
POWER
(8 R Bridged)
(4 R Bridged)
(2 Q Bridged)
(12.6 Vdc)
(14.4 Vdc)
Class A
5.2
Class A
10.2
THD
Signal to Noise
Frequency Response
Stereo Separation
Damping
Input Sensitivity
Input Impedance
Hawkins Bass Control
Sub Sonic Filter: No boost,
High Pass filter from
Hawkins Bass Control: 0
to +9
variable from 30 to 70 Hz.
Dimensions (W x D x H)
15.0" X 9.8" X
SOUNDSTREAM '
N
T
E
H
SOUNDSTREAM TECHNOLOGIES
120 Blue Ravine Road
ph 916.351.1288
warranty.
by a limited
1 R Stereo
112 R Stereo
(1 Q Bridged)
(14.4 Vdc)
(14.4 Vdc)
(14.4 Vdc)
250W x 2
250W x 2
xl)
250W x 2
500W x2
1000 Watts
20
Hz to 20 kHz * 0.5 dB
300
Ohms
1 Ok
13 to 30
Hz.
2.25"
L
California 95630 USA
fax 916.351.0414
l
Maximum
Rated
output
Watts
500
Power Amplifiers
E
Class A
5.2
Owner's Manual
and
Installation Guide
Advertisement
Table of Contents
Related Manuals for Soundstream RUBICON RUBICON Class A 5.2 102
Summary of Contents for Soundstream RUBICON RUBICON Class A 5.2 102
-
Page 1: Power Amplifiers
Dimensions (W x D x H) RUBICON Class A 5.2: 13.0” X 9.8” X 2.25” RUBICON Class A 10.2: 2.25” 15.0” X 9.8” X SOUNDSTREAM ’ SOUNDSTREAM TECHNOLOGIES 120 Blue Ravine Road Folsom California 95630 USA ph 916.351.1288 fax 916.351.0414... - Page 2 Conaratulations! You now own a Soundstream RUBICON CLASS A amplifier, the product of an uncompromising design and engineering philosophy. Your Soundstream RUBICON CLASS A amplifier will outperform any other amplifier in the world. To Maximize the performance of your system, we recommend that you thor- oughly acquaint yourself with its capabilites and features.
- Page 3 Ultra Low-Impedance Output Capablility: The RUBICONI 0.2 and 5.2 are designed for optimal performance into loads as low as l/2 or l/4 ohm stereo (1 or I/2 ohm mono). RUBITM(_Rapid-&e Banched _/mpulse) This new proprietary power sup- ply topology eliminates “power sags” during low frequency reproduction by rapidly increasing the duty cycle, stabilizing the power supply and allowing it to deliver the power required when reproducing low frequen- cies.
- Page 5 Hawkins Bass Control - Theorv and Use Hawkins Bass Control (parametric) subwoofer control circuit included with the Soundstream RUBICON Class A 10.2 and 5.2 am- plifiers. It is capable of removing subsonic energy HAWKINS in program material while boosting subwoofer fre- FREQ BOOST quencies.
- Page 6 ~INSTALLATI~N STEP SELECTING THE SPEAKER OUTPUT MODE Class A 10.2 and 5.2 The RUBICON amplifiers have the ability to operate in any one of the following modes: Stereo (STACT/Mjx& Mono): Use this mode for either stereo operation (left and right channels) or for Mixed Mono operation (stereo left and right channels plus bridged mono for a subwoofer).
-
Page 7: Sample Wiring Diagram
INSTALLATION STEP 3 ) WIRING POWER AND GROUND To ensure maximum output from your RUBICON amplifier, loss power and ground cables and connections. The RUBICON amplifiers will accept up to 4 gauge power and ground cables. Determine from the chart below the minimum gauge power and ground wire for your application. -
Page 8: Installation Step
INSTALLATION STEP 5 The input levels are adjusted by means of the individual channel input level controls located on the front of the amplifier. This is a unique dual-stage circuit that adjusts both level and gain. This topology maintains better S/N Ratio even when using sources with minimal output.
Need help?
Do you have a question about the RUBICON RUBICON Class A 5.2 102 and is the answer not in the manual?
Questions and answers