Subscribe to Our Youtube Channel
Related Manuals for Soundstream REFERENCE 405
Summary of Contents for Soundstream REFERENCE 405
-
Page 1: Power Amplifier
REFERENCE Power Amplifier OWNERS MANUAL INSTALLATION GUIDE SOUNDSTREAM@... -
Page 2: Design Features
CONGRATULATIONS You now own the REFERENCE405 Amplifier, the product of an uncompromising design and engineering philosophy. Your Soundstream REFERENCE amplifier will outperform any other amplifier in the world. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and your sales and installation receipts for future reference. - Page 3 SYSlEMDIAGRAVI# 1 Channels of input: 4 Bridged Channels: none Subwoofer Channel Impedance: 2 ohms High l%wr/l-iigh Current Ming: High I%WI SOUNDSTRE4M” REFERENCE 405 Connections i&t+ Fmel 24 d3Dct Stich Settings Battom Panel cIwwaS3&4 CI-wwELs1&2 SUClUWEL rmfa SlEm LOWS5 6Yw6s B\rppGs [-a HGH PPGS SLBCI-I ra CH 1.2.3or4...
-
Page 4: System Diagram
Subwofer Channel Impedance: 2 ohms High Power/High Current Setting: High her *Using outboard “dual amp balancer” to remotely adjust subwoofer level. SOUNDSTREA’vl” 0 0 I E s Et &I cuo&tim REFERENCE 405 24 dBPct HEAD UW shitch settings Bottom panel czl-tmNELs3&4 cHpNNLs1&2... -
Page 5: Plan The Installation
INSTALLATION 1. PLAN THE INSTALLATION Before you go any further with the installation of the amplifier, map out the system and the necessary wiring. Your work will be simplified if you have a plan of attack. Consider all electrical requirements, as well as physical, such as amplifier ventilation and availability of space. -
Page 6: Level Setting
5. WIRING The only tool needed to make wire terminations at the amplifier will be a flat blade-type screwdriver and either wire strippers or a knife. When baring wires for connection to the amplifier, remove approximately 98” of the insulation, insert into the terminal block, and tighten the screw. -
Page 7: Protection Circuits
8. PROTECTION CIRCUITS Your REFERENCE405 amplifier is protected against both overheating and short circuits by means of the following circuits: Main power supply fuses (2 at 20 amps each) Smart Power Supply Thermal Rollback activating at 85OC. A fail-safe thermal protection circuit activating at 95OC. Speaker over-current protection relays (on the 4 x 25 watt channels). - Page 8 SPEAKER WIRING CONFIGURATIONS Two4OhmSpeakers InFaralld=2Ohms Four 4 Ohm Speakers In Furallel = Tw4ohmspeakers InSeties=8Ohm SOUNDSTREAM TECHNOLOGIES 120 Blue Ravine Road Folsom California 95630 USA tel 916.351 .I288 fax 916.351.0414 ver2.07a...
Need help?
Do you have a question about the REFERENCE 405 and is the answer not in the manual?
Questions and answers
Untuk speaker pintu 4+subwoofer 1 Diagram pemasangan nya gimana ?
To install the Soundstream Reference 405 amplifier with 4 door speakers and 1 subwoofer, follow these steps:
1. Power and Ground Wiring:
- Use high-quality, low-loss power and ground cables.
- Connect a 4-gauge power cable from the battery to the amplifier.
- Ground the amplifier securely to the vehicle chassis.
2. Speaker Wiring:
- Channels 1 and 2: Connect to the front door speakers.
- Channels 3 and 4: Connect to the rear door speakers.
- Channel 5 (subwoofer channel): Connect to the subwoofer.
3. Speaker Output Mode Selection:
- Ensure channels 1-4 are set to operate in stereo mode for full-range sound.
- Set the subwoofer channel to low-pass mode.
4. Bass Control and Frequency Adjustment:
- Use the Hawkins Bass Control to tailor the subwoofer response.
- Adjust the frequency and boost settings as needed.
5. Testing and Final Adjustments:
- Play test audio and adjust gain levels for balanced output.
- Fine-tune crossover settings to match speaker specifications.
- Ensure all connections are secure and free of distortion.
This setup ensures optimal performance from the Reference 405 with 4 door speakers and a subwoofer.
This answer is automatically generated