Table of Contents
Advertisement
Quick Links
smart
Living
Installation · Programming · Operating
Keep this manual safe for reference and future maintenance
Introduction
General System Overview
Thank you for choosing the Yale Wireless Security
Alarm System. This simple to install system has
been designed with the user in mind.
The Siren has a sounder and strobe LEDs to
attract attention.
Number of devices
You can install up to 20 devices in the system. As
well as extra Door/Window Contacts, PIRs and Key
Pads, you can add Smoke Detectors, Key Fobs and
Panic Buttons.
Tamper proof system
Each part of the system is 'tamper' protected. Any
unauthorised tampering with the system will result in
an alarm. This feature can be turned off by the user
when a battery change is required.
Entry/Exit feature (for Kit with Key Pad)
The system has a 20 second entry/exit time. This
feature allows you time to leave the home when
arming the system. Upon entering, the feature allows
time to disarm the system without causing an alarm.
Take care of your safety
Display extreme caution when using ladders or
steps, please follow manufacturer instructions. Be
careful when using hand and power tools and follow
the manufacturers' guidelines when using them.
Take care that the correct tools are used. Wear
goggles or protective clothing where required.
The external Siren is extremely loud, please ensure
you replace the cover and retreat to a safe distance
before testing.
For more information on this product and
Yale Alarm Range visit www.yale.co.uk
Consumer Support: info@yale.co.uk
This system is NOT compatible with EF Series & SR Series
accessories. Compatible with HSA accessories only.
Standard Alarm Kit
(HSA6210-R)
Contents
Contents
Recommended Installation Sequence
We recommend you follow the easy start sequence,
headings numbered 1-5.
The 2 year guarantee for this Yale Alarm
Kit is active from the date of purchase
2
(A copy of this guarantee is available on
our website).
Please register online within
12 months of purchase at
www.yale.co.uk/registeryourproduct
Information and illustrations are subject to change within this
document. Yale reserves the right to alter the specification and
product design at anytime without notice. Yale® is a registered
trademark. © 2016 ASSA ABLOY. All rights reserved.
2
3-4
5
6-8
9-10
11
12
13
14
Advertisement
Table of Contents
Related Manuals for Yale Smart Living HSA6210-R
Summary of Contents for Yale Smart Living HSA6210-R
-
Page 1: Table Of Contents
Information and illustrations are subject to change within this accessories. Compatible with HSA accessories only. document. Yale reserves the right to alter the specification and product design at anytime without notice. Yale® is a registered trademark. © 2016 ASSA ABLOY. All rights reserved. -
Page 2: Location Planning
• Do not aim a PIR at this door or window. Key Fob Can be used outside the premises and kept on your keyring. Yale Key Pad PIR Motion Detector • The Key Pad should be sited next to the main point of entry/ exit so that the system can be disarmed/armed within 20 •... -
Page 3: Unpacking The System
Unpack all the parts External Siren HSA6050 The Siren comes in two shapes, square shaped and round depending on the kit purchased. The operation and programming of the Sirens are identical, only the case is different. WARNING The Siren is very loud, be prepared! Take care not to PIR Motion Detector HSA6020 activate the Siren tamper switch unnecessarily. - Page 4 Please note, the Home button on the operating panel and the jumper sw itch inside (do not move) On/Off sw itch Disarm have no function on this model. Home Yale Smoke Detector HSA3070 (Sold Separately) 1 Remove the cover and insert four AAA batteries. Door/Window Contact HSA6010...
-
Page 5: Programming The System
Programming the Siren-based system (without control panel) The Siren is the heart of the system. All components must be recognised by the Siren. Entering Learn mode: Exiting Learn mode: • Press the to exit the learn mode • Press and hold for 1 second. -
Page 6: Mounting Alarm Devices
Mounting alarm devices WARNING Before mounting the Key Pad and Siren ensure that the system tamper is disabled as described below. Disabling the system tamper Before you make the adjustment: • Disarm your system using your Key Fob Before mounting it is important to disable the (Press disarm) or Key Pad (Press disarm followed system tamper to avoid the Siren sounding an by the PIN code). - Page 7 Mounting the Door/Window Contact Fixing Slots X 2 Frame Keypad Cradle Open Door/Window 3 Slide the Key Pad into the cradle Magnet 4 Close the cradle cover so the logo is facing you Sensor Gap no more Gap approx 10mm Mounting the PIR Motion Detector than 8mm 1 Open the PIR by loosening the bottom screw.
- Page 8 -Mounting using screws and wall plugs The tamper switch will automatically reactivate after one hour. Alternatively you can enable the 1 Loosen the bottom screw tamper switch manually (optional). and open the Door/ Knockouts Window Contact. See Page 10, Table 1 and Table 2 for manual tamper switch reactivation using Key Pad or 2 Knock out the holes on the Key Fob.
-
Page 9: Using The System
Using the system Arm and disarm the system and practice using it. Trigger the alarm by arming the system and opening protected doors/windows and walking past PIRs. Now’s the time to set your PIN code and show the rest of the family how simple it is to use. Arming the system Changing your Key Pad PIN Key Pad/Key Fob: Press arm... - Page 10 Using the Panic Button Key Pad Modes: Table 1 Entering setting mode: Activate: Press and hold panic button for 2 Press Panic button A followed by PIN code (factory seconds, the LED will light briefly and the siren will . You can now select different function. default is 0000) be activated.
-
Page 11: Adding Accessories
Adding accessories To provide additional protection you can add extra Door/Window Contacts, PIRs, Key Fobs, Key Pads, Panic Buttons and Smoke Detectors. These are available separately from your local stockist. Key Fob Adding devices for the first time 1 Press the Arm and Home buttons together and See section 3 (page 5) for first time system continuously for 5 seconds until the LED stops installation. -
Page 12: Changing The Batteries
Changing the batteries Always use alkaline batteries or the correct type of coin cells as replacements because any other battery can cause problems with the operation of the system. Ensure the correct steps are taken when changing batteries in tamper protected devices. Siren 3 Using a screwdriver gently lever out the old battery. -
Page 13: Troubleshooting
Siren, see either Should you have any questions or experience a “Programming the siren based system” or “Adding problem with your Alarm Kit please contact our accessories” sections. Customer Support Helpline. Tel: 01902 364606 Monday - Friday 8:30am - 5:30pm Email: info@yale.co.uk... -
Page 14: Specifications
Specifications All Devices PIR Motion Detector Panic Button Radio Microprocessor controlled Alarm processing Microprocessor Environmental conditions 433.92MHz AM transmitter controlled dual edge sequential -10°C to 40°C, relative humidity Power supply 3V, CR2032 lithium pulse count with pulse length 70% non-condensing for all units coin cell battery. - Page 16 433.92M Hz AM transmitter 0560 NoPb 0560 V1-04/2019 THE YALE BRAND, with its unparalleled global reach and WEEE range of products, reassures more people in more countries Note: Waste electrical products and than any other consumer locking solution. batteries should not be disposed of with household waste.