CDP-XE570 The following caution label is located inside of the unit. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. CDP-XE570...
Page 4
CDP-XE570 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313: J-2501-126-A) is used for checking the display. To check, perform the following procedure.
Page 5
È É Ê Ë Ì Í Î Ï ···· Ñ Ò Ó Ô Õ Ö ···· are not displayed ´ Ù Ú Û Ü Y ···ø ÿ are not displayed T All the same T All the same T All the same CDP-XE570...
1 Turn the cam to the direction of arrow (counter clock wise) by tapering driver. 2 Take off the tray. SECTION 3 DISASSEMBLY 3 Screw (DIA. 12), floating BU-5BD27 CDP-XE570 Loading panel 4 Remove the Base unit (BU-5BD27) to the direction of arrow.
CDP-XE570 4-1. CHECK MODE The following checks can be performed in the CHECK Mode. • Offset value display Turn on the set. Put disc in the set. Press the [PLAY MODE] , H and M buttons simultaneously. The Offset measured values will be displayed as “AB 02 FE”...
OFFSET(VC)/EF.BIAS display OFFSET(RF,FE,TRK) display CLEAR RFCK/GFS/ERROR RATE check mode * NOTE : Other buttons are not used for servicing and should not be pressed without a reason. [ DISPLAY BOARD ] – Conductor side – l AMS L S531 CDP-XE570 AFADJ...
CDP-XE570 ELECTRICAL BLOCK CHECKING Note: CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. Use PATD-012 disc (3-702-101-01) unless otherwise indicated. Use an oscilloscope with more than 10M impedance. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
Page 11
Adjustment Location : [ DISPLAY BOARD ] – Conductor side – l AMS L S531 [ BD BOARD ] – Side B – TP(VC) IC101 TP(FE1) TP(TE1) TP(RF AC) CN102 AFADJ CDP-XE570...
CDP-XE570 6-4. PRINTED WIRING BOARD BD SECTION • See page 12 for Circuit Board Location. • Semiconductor Location Ref. No. Location IC101 *C-2 IC131 *C-1 IC150 *B-1 Q131 Q132 * : Side B There are a few cases that the part printed on this diagram isn’t mounted in this model.
CDP-XE570 6-6. PRINTED WIRING BOARD MAIN SECTION • See page 12 for Circuit Board Location. IC681 IC631 There are a few cases that the part printed on this diagram isn’t mounted in this model. IC801 IC671 IC672 IC901 IC603 IC601...
CDP-XE570 6-8. PRINTED WIRING BOARD DISPLAY SECTION • See page 12 for Circuit Board Location. • Semiconductor Location Ref. No. Location IC501 IC502 C-11 Q501 Q502 There are a few cases that the part printed on this diagram isn’t mounted in this model.
CDP-XE570 6-10. IC PINFUNCTIONS • IC501 MASTER CONTROL (CXP82832-033Q)(DISPLAY BOARD) Pin No. Pin Name FL grid signal output FL grid signal output – Connected to VDD – Connected to VDD SCOR Sub code sync input 6, 7 Connected to VDD...
1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK) 4-974-510-01 SCREW (+BV 3X8 CU)(UK) 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S (AEP) 0 T601 1-437-258-11 TRANSFORMER, POWER CDP-XE570 • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts of Color Cabinet’s Color The components identified by mark 0 or dotted line with mark 0 are critical for safety.
3-713-786-51 SCREW +P 2X3 4-917-566-01 GEAR (S) X-4917-504-1 MOTOR ASSY X-4917-523-3 BASE (OUTSET) ASSY M102 1-541-353-11 MOTOR (SLED) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. CDP-XE570 Remarks...
CDP-XE570 NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one.
Page 27
R525 1-249-421-11 CARBON 1/4W F R526 1-247-843-11 CARBON 1/4W F 1/4W F R527 1-249-427-11 CARBON 1/4W F R528 1-249-431-11 CARBON 1/4W F CDP-XE570 HEADPHONE Description Remarks 6.8K 1/4W F 1/4W F 1/4W F 1.5K 1/4W F 6.8K 1/4W F 100K...
Page 29
1/4W The components identified by mark 0 or dotted 1/4W F line with mark 0 are critical for safety. 1/4W Replace only with part number specified. 1/4W F CDP-XE570 MAIN POWER SW Description Remarks **************** < CAPACITOR > 0.0047uF 20.00% 250V <...
Page 30
CDP-XE570 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...