Table of Contents Section I Introduction Specifications .......................... 2 Classifications ........................2-3 Light Head Range of Motion ....................3 Dimensions ..........................4 Packaging ..........................4 Section II Installation Post Mount with Service Console ..................5-6 Post Mount for Magellan CMU ..................6 Section III Operation Light Switch ..........................7 Touch Pads ..........................7 Positioning Light ........................8 Eliminating Adjustable Arm Drift ..................
EverLight LED operatory light. ® Medical - General Medical Equipment The EverLight operatory light system is intended to Certified as to electrical shock, fire be used by trained professional dental care personnel and mechanical hazards only in accor- to provide shadow free illumination to the oral cavity dance with UL 60601-1, for dental practices.
Section I Introduction Explanation of Symbols and Signs: NOTICE = Caution In accordance with Part 15 of FCC rules, this equipment was tested and complies with Class = Warning A digital device limits. These limits are designed to give equipment reasonable protection against = Biohazard detrimental interference when operated in a commercial environment.
Post-Mount Arm Assembly Dimensions NOTICE Packaging For any questions about an order, please The EverLight components are packaged and shipped contact a DentalEZ Equipment customer service according to the packing list below. Please verify the representative at 1-866-DTE-INFO. carton contents against the packing list.
NOTICE light arm assembly spindle slot and engages Installation by an authorized DentalEZ dealer service the light arm assembly. Then loosen the set technician is recommended. screw two revolutions for clearance.
Section II Installation EverLight® (Post Mount) 3. Route the supplied power cord through the Light Arm Assembly bottom of the console and into the front of 1. Place the chair in its lowest position. the chair. (P-clamps provided in bag of supplies.) 2.
Section III Operation The EverLight dental light is designed to provide illu- Procedural Settings mination of the oral cavity for use by dental profes- • A - Sun - Color Matching - 5800° Kelvin sionals in the dental operatory. •...
(See Light Head Range Of Motion, Pg. 3.) Handles NOTICE To take full advantage of the EverLight's intensity and color correction, position the light between 20" and 45" away from the oral cavity. User Manual...
Section III Operation 3. Insert a 9/64 Allen wrench into the two small Eliminating Adjustable Arm Drift holes in the side of the adjustable arm and completely loosen the friction block. The adjustable arm is factory-adjusted to counter- balance the weight of the light head. If it becomes necessary to adjust the mechanism because of added 9/64 Allen weight, such as a mirror, perform the following steps:...
Section IV Care EverLight® (Post Mount) NOTICE Cleaning & Disinfecting Under normal use, there is no routine maintenance required. CAUTION Avoid spraying anything directly on the light. Spray cloth first, then wipe. CAUTION Do not use alcohol based disinfectants on plastic surfaces.
Disposal of Equipment The chart below should be used when troubleshoot- ing EverLight problems. If these suggested trouble- shooting procedures do not resolve the problem, see Disposal and Decommissioning of DentalEZ product the service instruction that follows.
Section VI Parts list/Diagrams EverLight® (Post Mount) Light Arm Part/Kit Name Part/Kit No. 1 Arm End Cap 3801-811 2 Rigid Arm Cap 3801-814 3 Post Bushing 3801-848 Light Head Part/Kit Name Part/Kit No. 4 Switch Lever & Boot 3802-353 5 On/Off Switch...
EverLight ® DentalEZ Group and its employees are proud of the products we provide to the dental community. We stand behind these prod- ucts with a warranty against defects in material and workmanship as provided below. In the event that you experience difficulty with the application or operation of any of our products, please contact our Technical Service Department at our expense at 1-866-DTE-INFO (1-866-383-4636).
Wiring Schematic EverLight® (Post Mount) OUTPUT INPUT 12 VDC, 40 W 100-240 VAC, 50/60 HZ Power Supply Black (Line) White (Neutral) Green (Ground) User Manual...
Guidance and manufacturer’s declaration - electromagnetic emissions The EverLight Light is intended for use in the electromagnetic environment specified below. The customer or the user of the EverLight should assure that it is used in such an environment. Emissions test Compliance Electromagnetic environment –...
Page 17
Guidance and manufacturer’s declaration – electromagnetic immunity The EverLight is intended for use in the electromagnet environment specified below. The customer or the end user of the EverLight should assure that it is used in such an environment. IEC 60601...
Page 18
Recommended separation distance between Portable and mobile RF communications equipment and the model @ 3Vrms The EverLight is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the EverLight can help prevent...
Page 19
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the EverLight is used exceeds the applicable RF compliance level above, the EverLight should be observed to verify normal operation.
Need help?
Do you have a question about the EverLight and is the answer not in the manual?
Questions and answers