Related Manuals for Sony SLV-SE80EN/EG
Summary of Contents for Sony SLV-SE80EN/EG
- Page 1 Video Cassette Recorder Operating Instructions PAL NTSC 4.43 SLV-SE80EN/EG ©1999 by Sony Corporation 3-865-443-13 (1)
- Page 2 WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Mains lead must only be changed at a qualified service shop.
-
Page 3: Table Of Contents
Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 9 Step 3: Connecting the VCR 14 Step 4: Tuning your TV to the VCR 16 Step 5: Setting up the VCR with the Auto Set Up function 18 Step 6: Setting the clock 23 Selecting a language 24 Presetting channels... -
Page 4: Getting Started
Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • R6 (size AA) batteries • Audio cable Checking your model name The instructions in this manual are for the 2 models: SLV-SE80EN and SE80EG. -
Page 5: Step 2: Setting Up The Remote Commander
(+) end clicks into position. Using the remote commander You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. - Page 6 Step 2 : Setting up the remote commander (continued) TV control buttons Turn the TV into standby mode Select an input source of the TV either from aerial in or from line in Select the programme position of the TV Getting Started WIDE AUDIO MONITOR...
-
Page 7: Controlling Other Tvs With The Remote Commander
• Some buttons may not work with certain Sony TVs. Controlling other TVs with the remote commander The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the table on the next page, set the appropriate manufacturer’s code number. - Page 8 If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. To make wide mode settings, see the footnotes below this table for the applicable code numbers. Manufacturer Sony Akai Ferguson Grundig Hitachi...
-
Page 9: Step 3: Connecting The Vcr
Step 3 Connecting the VCR If your TV does not have a EURO-AV connector, see page 12. If your TV has a EURO-AV (Scart) connector Mains lead to mains : Signal flow Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. - Page 10 Step 3 : Connecting the VCR (continued) Connect LINE-1 (TV) on the VCR and the EURO-AV (Scart) connector on the TV with the optional EURO-AV cable. This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press … TV/ VIDEO to display the VIDEO indicator in the display window.
- Page 11 About the SMARTLINK features If the connected TV complies with SMARTLINK, MEGALOGIC , EASYLINK VIEW LINK , you can use the SMARTLINK function after you complete the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV).
- Page 12 Step 3 : Connecting the VCR (continued) If your TV does not have a EURO-AV (Scart) connector Mains lead to mains : Signal flow Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.
-
Page 13: Additional Connections
Additional connections To a stereo system You can improve sound quality by connecting a stereo system to the AUDIO OUT R/L jacks as shown on the right. To a TV that has audio/video (A/V) input jacks (SLV-SE80EG only) This additional connection improves picture and sound quality. -
Page 14: Step 4: Tuning Your Tv To The Vcr
Step 4 Tuning your TV to the VCR If you have connected the VCR to your TV using the EURO-AV cable, skip this step. I/u ON/STANDBY ON/STANDBY Press I/u ON/STANDBY to turn on the VCR. Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. - Page 15 RF channel appears. Then tune the TV to the new RF channel until a clear picture appears. Note • If you set the wrong TV system, you may have no sound or sound may be distorted. SONY VIDEO CASSETTE RECORDER Getting Started...
-
Page 16: Step 5: Setting Up The Vcr With The Auto Set Up Function
Step 5 Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display, TV channels, guide channels for the ShowView system. - Page 17 Press AUTO SET UP lightly. AUTO SET UP The VCR starts searching for all of the receivable channels and presets them according to the TV system you selected in “Tuning your TV to the VCR.” If you use the SMARTLINK connection, the Preset Download function starts and the SMARTLINK indicator flashes in the display window during download.
-
Page 18: Step 6: Setting The Clock
Step 6 Setting the clock You must set the time and date on the VCR to use the timer recording features properly. The Auto Clock Set function works only if a station in your area is broadcasting a time signal. If the Auto Set Up function did not set the clock correctly for your local area, try another station for the Auto Clock Set function. - Page 19 Press >/. to highlight MANUAL ADJUST, then press OK. PLAY Press >/. to set the date. PLAY Press / to highlight the month and set the month pressing >/.. PLAY Set the year, hour, and minutes in sequence, pressing / to highlight the PLAY item to be set, and press >/.
- Page 20 Step 6 : Setting the clock (continued) Press OK to start the clock. PLAY MENU Press MENU to exit the menu. Tips • To change the digits during setting, press ? to return to the item to be changed, and select the digits pressing >/.. •...
-
Page 21: Before You Start
Changing the station for the Auto Clock Set function Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU Press MENU, then press >/. to highlight SETTINGS and press OK. PLAY Press >/. - Page 22 Step 6 : Setting the clock (continued) Press >/. to highlight ON, then press PLAY Press . to highlight CLOCK PROG, then press OK. PLAY Press >/. repeatedly until the programme position of the station that PLAY carries the time signal appears. If the VCR does not receive the time signal from any station, AUTO ADJUST returns to OFF automatically.
-
Page 23: Selecting A Language
Selecting a language You can change the on-screen display language from the one you selected with the Auto Set Up function. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU Press MENU, then press >/. -
Page 24: Presetting Channels
Presetting channels If some channels could not be preset using the Auto Set Up function, you can preset them manually. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU Press MENU, then press >/. - Page 25 Press >/. to highlight NORMAL/ CATV, then press OK. PLAY Press >/. to highlight NORMAL, then press OK. PLAY To preset CATV (Cable Television) channels, select CATV. Press PROG +/– to select the programme • PROG position. Press >/. to highlight CHANNEL SET, then press OK.
- Page 26 Presetting channels (continued) Press >/. repeatedly until the channel you want is displayed. PLAY The channels appear in the following order: B/G TV system Channel number in the CHANNEL SET field C21–C69 S01–S41 S42–S46 If you know the number of the channel you want, press the programme number buttons.
- Page 27 Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. In step 7 above, press programme number button “0” twice to display the number “00” beside CHANNEL SET. Press MENU to exit the menu.
-
Page 28: Changing/Disabling Programme Positions
Changing/ disabling programme positions After setting the channels, you can change the programme positions and station names as you like. If any programme positions are unused or contain unwanted channels, you can disable them. Changing programme positions Before you start… •... - Page 29 Press >/. to highlight the row on which you want to change the programme PLAY position, then press /. To display other pages for programme positions 6 to 60, press >/. repeatedly. Press >/. until the selected channel row moves to the desired programme PLAY position.
- Page 30 Changing/disabling programme positions (continued) Changing the station names You can change the station names (up to 5 characters). Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. MENU Press MENU, then press >/. to highlight LISTS and press OK.
- Page 31 Press >/. to highlight the row on which you want to change the station PLAY name, then press /. To display other pages for programme positions 6 to 60, press >/. repeatedly. Press /. PLAY Enter the station name. 1 Press >/. to select a character. PLAY Each time you press >, the character changes as shown below.
- Page 32 Changing/disabling programme positions (continued) Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. Before you start… • Turn on the VCR and the TV. •...
- Page 33 Press >/. to highlight CHANNEL LIST, then press OK. PLAY Press >/. to highlight the row on which you want to disable. PLAY Press CLEAR. CLEAR The selected row will be cleared as shown on the right. Repeat steps 3 and 4 for any other programme positions you want to disable.
-
Page 34: Setting The Canal Plus Decoder
Setting the Canal Plus decoder You can watch or record Canal Plus programmes if you connect a decoder (not supplied) to the VCR. Connecting a decoder DECODER/… LINE-3 IN : LINE-1 (TV) Getting Started EURO-AV cable (supplied with decoder) EURO-AV (Scart) AERIAL OUT Aerial cable... - Page 35 Setting Canal Plus channels To watch or record Canal Plus programmes, set your VCR to receive the channels using the on-screen display. Before you start… • Turn on the VCR, the TV, and the decoder. • Set the TV to the video channel. MENU Press MENU, then press >/.
- Page 36 Setting the Canal Plus decoder (continued) Press >/. to highlight DECODER, then press OK. PLAY MENU Press MENU to exit the menu. MENU Press MENU, then press >/. to highlight SETTINGS and press OK. PLAY Press >/. to highlight TUNER, then press OK.
- Page 37 Press >/. to highlight NORMAL, then press OK. PLAY To preset CATV (Cable Television) channels, select CATV. • PROG Press PROG +/– to select the desired programme position. Press >/. to highlight CHANNEL SET, then press OK. PLAY Press >/. to select the Canal Plus channels, then press OK.
- Page 38 Setting the Canal Plus decoder (continued) Press >/. to highlight ON, then press PLAY MENU Press MENU to exit the menu. • If you want to return to the previous menu, highlight RETURN and press OK. Notes • The menu disappears automatically if you don’t proceed for more than a few minutes.
-
Page 39: Basic Operations
Basic Operations Playing a tape NTSC PB Turn on your TV and set it to the video channel. Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. 6 EJECT DISPLAY CLEAR ·... - Page 40 Playing a tape (continued) Press · PLAY. PLAY When the tape reaches the end, it will rewind automatically. Additional tasks Stop play Pause play Resume play after pause Fast-forward the tape Rewind the tape Eject the tape To set the colour system If the playback picture has no colour, or streaks appear during playback, set COLOUR SYSTEM in the OPTIONS-1 menu to conform to the system that the tape was recorded in (see page 72).
- Page 41 To use the time counter At the point on the tape that you want to find later, press CLEAR. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. VIDEO To display the counter on the TV screen, press Notes •...
-
Page 42: Starting Playback Automatically With One Button
Playing a tape (continued) Starting playback automatically with one button (One Touch Play) If you use the SMARTLINK connection, you can turn on the VCR and the TV, set the TV to the video channel, and start playback automatically with one button. -
Page 43: Recording Tv Programmes
Recording TV programmes Turn on your TV and set it to the video channel. To record from a decoder, turn it on. Insert a tape with its safety tab in place. COUNTER/ REMAIN DISPLAY SP/LP … TV/VIDEO INPUT SELECT PROG +/– r REC p STOP continued... - Page 44 Recording TV programmes (continued) INPUT SELECT Press INPUT SELECT until a programme position number appears in the display window. • PROG Press PROG +/– to select the programme position you want to record. SP / LP Press SP/LP to select the tape speed, SP or LP. LP (Long Play) provides recording time twice as long as SP, however, SP (Standard Play) produces better picture and audio quality.
- Page 45 To check the remaining time Press DISPLAY. With the display on, press COUNTER/REMAIN to check the remaining time. Each time you press COUNTER/REMAIN, the time counter and the remaining time appear alternately. The remaining time with the indicator also appears in the display window. 0 : 0 0 : 2 Time counter To correctly check the remaining time of the tape, set TAPE LENGTH in the...
- Page 46 Recording TV programmes (continued) Tips • To select a programme position, you can use the programme number buttons on the remote commander. For two-digit numbers, press the ? (ten’s digit) button followed by the programme number buttons. • You can select a video source from the LINE-1 (TV) connector, the LINE-2 IN jacks, or the LINE-3 IN (Scart) connector also using the INPUT SELECT button.
-
Page 47: Recording What You Are Watching On The Tv
Recording what you are watching on the TV (TV Direct Rec) If you use the SMARTLINK connection, you can easily record what you are watching on the TV (other than tapes being played on the VCR). Insert a tape with its safety tab in place. Press r REC while you are watching a TV programme or external source. -
Page 48: Recording Tv Programmes Using The Showview System
Recording TV programmes using the ShowView system The ShowView system is the feature that simplifies programming the VCR to make timer recording. Just enter the ShowView number listed in the TV programme guide. The date, times, and programme position of that programme are set automatically. - Page 49 Press the programme number buttons to enter the ShowView number. If you make a mistake, press CLEAR and re-enter the correct number. CLEAR Press OK. PLAY The date, start and stop times, programme position, tape speed, and VPS/PDC setting appear on the TV screen. •...
- Page 50 Recording TV programmes using the ShowView system (continued) If you want to change the date, tape speed, and the VPS/PDC function PLAY setting: 1 Press ?// to highlight the item you want to change. 2 Press >/. to reset it. •...
- Page 51 Timer recording with VPS/PDC signals Some broadcast systems transmit VPS (Video Programme System) or PDC (Programme Delivery Control) signals with their TV programmes. These signals ensure that your timer recordings are made regardless of broadcast delays, early starts, or broadcast interruptions (with the VPS or PDC indicator in the display window lit).
- Page 52 Recording TV programmes using the ShowView system (continued) Tips • To set the programme position with a two digit number, press ? (ten’s digit) button followed by the programme number button. • To set the programme position, you can also use the PROG +/– button or programme number buttons.
-
Page 53: Setting The Timer Manually
Setting the timer manually If the ShowView system is not available in your area, follow the instructions below to set the timer to record programmes. Before you start… • Check that the VCR clock is set to the correct time and date. •... - Page 54 Setting the timer manually (continued) Set the date, start and stop times, programme position, tape speed, and PLAY VPS/PDC function: 1 Press / to highlight each item in turn. 2 Press >/. to set each item. To correct a setting, press ? to return to that setting and reset.
- Page 55 Daily/weekly recording In step 2 above, press . to select the recording pattern. Each time you press ., the indication changes as shown below. Press > to change the indication in reverse order. TODAY n SUN-SAT (Sunday to Saturday) n MON-SAT (Monday to Saturday) n MON-FRI (Monday to Friday) n SAT (every Saturday) ...
-
Page 56: Additional Operations
Additional Operations Playing/searching at various speeds Playback options View the picture during fast-forward or rewind Play at high speed Additional Operations · PLAY ) FF 0 REW Shuttle ring Operation During fast-forward, hold down )# FF/) FF. During rewind, hold down 03 REW/0 REW. •... -
Page 57: Using The Shuttle Ring
Playback options Operation Play at twice the normal During playback, press 2. speed Play in slow motion During playback, press & SLOW. Play frame by frame During pause, press )# FF or 03 REW on the remote commander. Hold down )# FF or 03 REW to play one frame each second. - Page 58 Playing/searching at various speeds (continued) To use the shuttle ring in jog mode Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The JOG button lights up. If you change to the jog mode during any playback mode, the playback pauses so you can see a still picture.
-
Page 59: Setting The Recording Duration Time
Setting the recording duration time After starting recording in the normal way, you can have the VCR stop recording automatically after a specified duration. While recording, press r REC. indicator appears in the display window. Press r REC repeatedly to set the duration. Each press advances the time in increments of 30 minutes. -
Page 60: Checking/Changing/Cancelling Timer Settings
Checking/ changing/ cancelling timer settings Before you start… • Turn on your TV and set it to the video channel. Press I/u to turn on the VCR. Press MENU, then press >/. to highlight LISTS and press OK. Press >/. to highlight TIMER LIST, then press OK: •... - Page 61 Press >/. to select the setting you want to change or cancel, then press OK. The selected setting appears in the TIMER menu. • To change the setting, press ?// to highlight the item you want to change, and press >/. to reset it. •...
-
Page 62: Recording Stereo And Bilingual Programmes
Recording stereo and bilingual programmes In ZWEITON (German stereo) system This VCR automatically receives and records stereo and bilingual programmes based on the ZWEITON system. When a stereo or bilingual programme is received, the STEREO indicator appears in the display window. - Page 63 Bilingual programme To listen to On-screen display Main MAIN Main and sub MAIN/SUB Standard sound* No indicator * Usually the main sound (monaural) Selecting the sound during playback Press AUDIO MONITOR to select the sound you want. On-screen display To listen to STEREO Stereo/main and sub (left and right channels)
- Page 64 Recording stereo and bilingual programmes (continued) Notes • To listen to playback sounds in stereo, you must use the EURO-AV or AUDIO OUT connections. • When you play a tape recorded in monaural, the sound is heard in monaural regardless of the AUDIO MONITOR setting. •...
-
Page 65: Searching Using The Smart Search Function
Searching using the Smart Search function If you record multiple programmes on a tape, use the Smart Search function to see what has been recorded on your tape. You can see information such as date, time, and channel of programmes recorded on a tape. - Page 66 Searching using the Smart Search function (continued) To stop searching Press p STOP. To exit the SMART SEARCH screen Press SMART SEARCH. To record in a blank space Blank space on the tape will appear as a blank row in the SMART SEARCH screen.
- Page 67 Notes • If you begin recording a programme “D” from the middle of a previously recorded programme “A” and into another previously recorded programme “B,” the Smart Search information for the second programme “B” which is recorded over is deleted. Originally recorded programmes Recording the programme “D”...
-
Page 68: Searching Using The Index Function
Searching using the index function The VCR marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording. Insert an indexed tape into the VCR. Press =/+ INDEX SEARCH. •... -
Page 69: Adjusting The Picture
Adjusting the picture Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then goes off), distortion may occur if the tape was recorded in poor condition. In this case, manually adjust the tracking. - Page 70 Adjusting the picture (continued) About the Optimum Picture Control (OPC) function The Optimum Picture Control (OPC) function automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set OPC to ON in the OPTIONS-1 menu (with the OPC indicator in the display window lit).
-
Page 71: Changing Menu Options
Changing menu options Press MENU, then select OPTIONS and press OK. Press >/. to highlight OPTIONS-1 or OPTIONS-2, then press OK. Press >/. to select the option, then press OK. Press >/. to change the setting, then press OK. Press MENU to return to the original screen. OPTIONS - 1 EDIT AUDIO MIX... - Page 72 Changing menu options (continued) Menu choices Initial settings are indicated in bold print. OPTIONS-1 Menu option EDIT AUDIO MIX HIFI AUDIO (SLV-SE80EN only) AUTO LONG PLAY TAPE LENGTH COLOUR SYSTEM Additional Operations Set this option to • ON to switch on the OPC (Optimum Picture Control) function and improve picture quality.
- Page 73 OPTIONS-2 Menu option Set this option to DECODER/LINE3 • DECODER to use the DECODER/LINE-3 IN connector as the PAY-TV/Canal Plus decoder connector. • LINE3 to use the DECODER/LINE-3 IN connector as the line input connector. TIMER OPTIONS • VARIABLE to display the TIMER METHOD menu for selecting STANDARD or SHOWVIEW when pressing TIMER button.
-
Page 74: Editing
Editing Connecting to a VCR or stereo system How to connect to record on this VCR This VCR (Recorder) : Signal flow This VCR (Recorder) DECODER/ … LINE-3 IN : Signal flow • You can also use the LINE-1 (TV) connector instead. Notes •... -
Page 75: Basic Editing
Basic editing (when recording on this VCR) Before you start editing • Turn on your TV and set it to the video channel. • Press INPUT SELECT to display “L2” (“L1” or “L3”) in the display window. • Press SP/LP to select the tape speed, SP or LP. •... -
Page 76: Audio Dubbing
Audio dubbing This feature lets you record over the normal audio track. The monaural sound previously recorded is replaced while the original hi-fi sound remainds unchanged. Use this feature to add commentary to a tape that you have recorded with a camcorder. Before you start…... - Page 77 Press AUDIO DUB. The programme position changes to “L2,” and the in the display window. To start editing, press the P PAUSE buttons on this VCR and the stereo system (or other VCR) at the same time. When the counter reaches “0H00M00S,” audio dubbing stops automatically.
-
Page 78: Additional Information
Do not use a commercially available liquid type cleaning cassette other than Sony’s, as it may damage the video heads. • The video heads may have to be replaced. Consult your local Sony service facility for more information. - Page 79 Symptom The picture is no colour. The picture rolls vertically during picture search. The picture has no sound. No TV programme appears on the TV screen. TV reception is poor. The tape starts playing as soon as it is inserted. The tape is ejected when you press r REC.
- Page 80 Troubleshooting (continued) Symptom A tape cannot be inserted. The remote commander does not function. You cannot watch or record Canal Plus programmes. “L3” does not appear in the display window. The SMARTLINK function does not work. The tracking meter does not appear on the TV screen.
-
Page 81: Specifications
Specifications System Channel coverage PAL (B/G, D/K) VHF E2-E12, R1-R12 UHF E21-E69, R21-R69 CATV S1-S41, S01-S05 RF output signal UHF channels 21 to 69 Aerial out 75-ohm asymmetrical aerial socket Inputs and outputs : LINE-1 (TV) 21-pin Video input: pin 20 Audio input: pins 2 and 6 Video output: pin 19 Audio output: pins 1 and 3... -
Page 82: Index To Parts And Controls
Index to parts and controls Refer to the pages indicated in parentheses ( ) for details. Front panel 1 I/u ON/STANDBY switch/ indicator (14) 2 Tape compartment 3 § EJECT button (40) 4 0 REW (rewind) button (40, 56) 5 ) FF (fast-forward) button (40, 56) 6 ·... - Page 83 Display window STEREO NICAM LP 1 Timer indicator (50, 54) 2 NICAM indicator (SLV-SE80EN only) (62) 3 STEREO indicator (62) 4 Tape speed indicators (44) 5 VIDEO indicator (10, 45) 6 VPS (Video Programme System)/ PDC (Programme Delivery Control) indicator (51) 7 OPC (Optimum Picture Control) indicator (70) VIDEO VPS...
- Page 84 Index to parts and controls (continued) Rear panel (SLV-SE80EN) 1 Mains lead (9, 12) 2 AERIAL IN ANTENNE ENTREE connector (9, 3 AERIAL OUT ANTENNE SORTIE connector (9, 4 NTSC PB (Play Back) switch (40) Additional Information 5 DECODER/… LINE-3 IN DECODEUR/…...
- Page 85 Rear panel (SLV-SE80EG) 1 Mains lead (9, 12) 2 AERIAL IN ANTENNE ENTREE connector (9, 3 AERIAL OUT ANTENNE SORTIE connector (9, 4 NTSC PB (Play Back) switch (40) 5 DECODER/… LINE-3 IN DECODEUR/… ENTREE LIGNE-3 connector (34, 74) 6 : LINE-1 (TV) : LIGNE-1 (TV) connector (10, 34) 7 LINE-2 OUT VIDEO/AUDIO L/R jacks (13)
-
Page 86: Remote Commander
Index to parts and controls (continued) Remote commander Additional Information 1 6 EJECT button (40) 2 WIDE button (for TV) (7) 3 AUDIO MONITOR button (62) 2 button* (57) 5 & SLOW button* (57) 6 SP (Standard Play)/LP (Long Play) button (44) 8 ? (ten’s digit) button (6, 46) 9 . -
Page 87: Index Search
!£ TV / VIDEO remote control switch !¢ I/u (on/standby) switch (6, 50) !∞ COUNTER/REMAIN button (45) V (Teletext) button (for TV) (7) !§ AUDIO DUB button (77) ; TV power on/TV mode select button (for TV) (7) !¶ =/+ INDEX SEARCH buttons* (68) !•... -
Page 88: Index
Dubbing. See Editing E, F, G Editing 74 EP mode 41 EURO-AV connection Hi-fi audio track 63 I, J, K Index Search 68 Sony Corporation Language selecting 23 Safety tab 45 LP mode 44 Searching Monaural 63 Monitoring during playback 63...