Troubleshooting - Sony PS3 CECH-ZCM1U Instruction Manual

Checking the version ot the PS3™ system software
To use the motion contro!!er, the PS3~ system so‫؛‬tware must be version 3.40 or later. You can
check the system sodare version by selecting
(System Information] on the ΧΜΒ~ menu of the PS3" system.
Pairing the motion controller and the PS3٢" system
Before using the motion controller, you must first register or "pair" the motion controller and
the PS3" system. You only need to do this the first time you use the motion controller.
ใ Turn on the PS3™ system.
2 Connect the motion controller to the PS3™ system using a USB cable.
3 Press the PS button on the motion controller.
The motion controller is paired with the PS3" system.
(Settings)
٥ (System Settings)
Hints
٠ Ifyou press and hold the T button, you can move the motion controller to navigate the IB-
menu. Press the Move button to select an item.
‫ ا‬If you press and hold down the PS button fo r at least one second, you can check the assigned
controller number on the screen.
٠ To quit a game, press the PS button on the motion controller) and then select
® (Quit Game).
Adjusting the motion controller's settings
You can change settings fo r the motion controller by selecting
Settings) on the IB- menu of the PS3" system.
(Game)
(Settings) § (Accessory
Reassign Controllers If a port or number for the motion controller is specified by the
software, you can use this setting to assign the appropriate
controller port or number.
Hints
٠ A USB cable is not included. Use the USB cable supplied with the PS3™ system or any t^^e A -
mini-B USB cable to connect or charge the product.
٠ You can use up to four motion controllers at one time.
٠ When a paired motion controller is used with another PS3~ system, the pairing with the
original system is cleared. Pair the motion controller with the system again if it has been used
with another system.
Controller Vibration
Function
You can set the vibration function to on or off. It is set to (On) by
default.
Hint
You can change settings during gameplay by pressing the PS button on the motion controller.
Select
Settings] from the screen that is displayed wlien you press the PS button
(Settings) § (Accessory Settings) on the IB- menu, or select (Controller
Charging the motion controller
To use the motion controller, its battery must be charged, with the PS3™ system turned on
(power indicator Is lit solid green), connect the motion controller to the system using a USB
cable. The status indicator of the motion controller flashes slowly and charging begins. The
status indicator stops flashing when charging is complete.
Hints
٠ If you press and hold down the PS button on the motion controller for at least one second, you
can check the battery charge level on the screen.
٠ Charge in an environment where the temperature range is between I0٥c - 30٥c (50٥F - 86°F).
Charging may not be as effective when performed in other environments.
٠ The battery has a limited lifespan. Battery charge duration gradually decreases with repeated
usage and age. Battery life also varies depending on the storage method, usage state,
environment and other factors.
٠ If you do not plan to use the motion controller fo r an extended period of time, it is
recommended that you fully charge it at least once a year to help maintain battery
functionality.
« Battery duration may vary depending on usage conditions and environmental factors.
Troubleshooting
Go through this section if you experience difficulty in operating the motion controller. Should
any problem persist, visit http://-.us.playstatl0n.C0m or call SCEA Consumer Services at 1-
800-345-7669 for assistance.
The motion controller Is not detected correctly, or the response Is slow.
The motion controller may not be detected correctly if it is used in a location where the
lighting is too bright or if it Is exposed to direct sunlight.
Check that there are no obstacles between the PlayStatlomEye camera and the motion
controller.
The motion controller may not be detected correctly If it is too far away from the
PlayStation«Eye camera. The recommended distance between the camera and the motion
controller is about 1 to 3 meters (3 to 10 feet).
Set the PlayStation.Eye camera to the wide angle view (see "Setting up the PlayStation.Eye
camera").
The motion controller operates in an abnormal manner, or cannot be used as intended.
Try resetting the motion controller by pushing the reset button on the controller rear with a
thin-tipped object such as a pen.
Using the motion controller
Setting up the PlayStatloneEye camera
1 Set the PlayStatlonsEye camera (sold separately) to wide angle view.
If the camera Is not set to wide angle view, the motion controller will not be recognized
correctly.
o
Reset button
Set the lens angle marker so that It
Is in line with the blue lens angle
indicator.
Check that the motion controller is not being used or placed near magnetic sources
Perform the calibration operation on the motion controller's internal sensor. Select i
i (Accessory Settings) ٠ (Calibrate Motion Controller] on the IB- menu
Follow the on-screen instructions to complete the operation.
The motion controller does not function.
The motion controller must be paired with the PS3~ system through a controller number
assigned by the system or software. With the system turned on (power indicator is lit solid
green), connect the system and the motion controller using a USB cable, and then press the
PS button on the motion controller.
Check the charge level of the motion controller battery. The motion controller will not
function if the battery does not have any charge left. Charge tlie battery by connecting the
motion controller to the system using a USB cable.
(Settings)
2 Connect the camera's USB connector to one of the USB connectors on the PS3™
system.
3 Place the camera centered on theTV screen.
Position the camera at the top or bottom of the TV screen.
At the top of theTV screen
Atthe bottom oftheTVscreen
The battery does not charge or does not fully recharge.
The batte^ can only be charged when the PS3'" system is turned on (power indicator is lit
solid green).
The motion controller does not vibrate.
Check that (Controller Vibration Function] under
Settings) is set to (On).
The sOfovare may not support the vibration function. Refer to the instruction manual for the
software.
g (Accessory (Settings)
Using the controller
Notice
Do not use the motion controtler while it is connected to the PS3" system with a USB cable, as
this restricts motion. Use in this manner could also result in damage to the connector or injury
if the USB cable is suddenly pulled from the PS3'" system.
1 Turrt on the PS3™ system.
2 Press the Ρ5 button on the motion controller.
A number is autontatically assigned to the motion controller.
3 Wear the strap on your wrist.
When disposing of the motion controller
When disposing of the motion controller, remove the battery and follow local regulations
regarding disposing of batteries.
blotice
other than when disposing of the motion controller, never remove the screws and never
remove the battery from the motion controller.
Removing the battery
1 Disconnect the USB cable from the motion controller.
Use the strap lock to tighten the strap.