Sony RM-EZ2 Operating Instructions

3-252-844-11(1) Setting Up the Remote Commander
About Presetting the Commander
The Commander is preset at the factory to operate Sony brand
components.
If you're using the Commander with a Sony component, you
won't need to preset the Commander before you start using it.
To set up the Commander to use with other (non-Sony)
Remote Commander
manufacturers' components, or to use with a component that is
not preset at the factory, you'll need to follow the instructions in
this manual to preset the Commander with the correct code
number for your components. (See the supplied "Component
Operating Instructions
Code Numbers" also.)
Manual de instrucciones (parte posterior)
Component that can be
preset
TV
Analog cable box
Notes
•The Commander can be set up to operate only one component
per button – unless their code numbers happen to be the same.
For example, you cannot set up the Commander to operate a
Sony TV and a Panasonic TV simultaneously (because they use
RM-EZ2 different code numbers).
•You may not be able to operate even a Sony brand component
with the factory presetting. In such a case, follow the
© 2003 Sony Corporation Printed in China
procedure in "Setting the Code."
Installing the Batteries
Before replacing the batteries, have new ones ready
beforehand.
Slide open the battery compartment and insert two size AA (R6)
English
batteries (not supplied).
Be sure to line up the + and – on the batteries with the + and –
on the battery compartment.
For the customers in the U.S.A.
1
WARNING
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
When to replace the batteries
installation. If this equipment does cause harmful interference
Under normal conditions, batteries will last up to 6 months. If
to radio or television reception, which can be determined by
the Commander does not operate properly, the batteries might
turning the equipment off and on, the user is encouraged to try
be worn out. Replace the batteries with new ones.
to correct the interference by one or more of the following
Notes
measures:
• Reorient or relocate the receiving antenna. •Replace both batteries with new ones.
• Increase the separation between the equipment and receiver. •Do not take more than 3 minutes to replace the batteries;
• Connect the equipment into an outlet on a circuit different otherwise, your setting of the code numbers will be erased.
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for Notes on Batteries
help.
•Do not mix old batteries with new ones or mix different types
You are cautioned that any changes or modifications not
of batteries together.
expressly approved in this manual could void your authority to
•If the electrolyte inside the battery should leak, wipe the
operate this equipment.
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the
electrolyte from leaking, remove the batteries when you plan
not to use the Commander for a long period of time.
Setting the Code
Follow the steps 1 and 2 below for each component you plan to
use with the Commander.
Step 1: Entering the Code Number
1 See the supplied "Component Code numbers", and find the
three-digit code number for the desired component.
If more than one code number is listed, use the number that's
listed first to complete the steps below.
For example, if you're setting up a Philips' TV, you would use
the code number 056.
If your component isn't listed, see "Searching for the Correct
Code."
2 While pressing the SET
Button Factory setting
button, press the POWER
button.
TV Sony TV
3 Press the button of the
CBL —
component that you want to
set up.
4 Enter the component's code
number. For example, if you're
entering the code for a Philips TV,
Your Code Number
you would press -56.
5 Press and release the ENT button to
store the code number in the
Commander's memory.
6 Go to "Step 2: Checking if the Code Number Works" to finish
setting up.
If you press a wrong button in step 4
Press the POWER button while pressing the SET button and
then go back to step 2.
Step 2: Checking if the Code Number Works
1 Power on the component you want to set up.
2 Aim the Remote Commander at the component and press a
2
button to check if that button works.
For example, press the POWER button to see if it works on
your component .
3 Check that the other buttons of the Commander is operating
the corresponding functions of the component.
You can write down the code number on the label inside the
battery compartment lid.
If the Commander Doesn't Seem to Be Working...
•First, try repeating these setup procedures using the other
codes listed for your component (see the supplied "Component
Code Numbers").
•If – after trying all the codes listed for your component – you
still cannot get the Commander to work properly, try the
search method described in "Searching for the Correct Code."
Searching for the Correct Code
If you've tried all the code numbers listed for your component
and you still cannot get the Commander to work (or if your
component is not listed in the "Component Code Numbers"
tables), try these steps.
1 Power on the component you want to set up. Insert a tape or
disc if necessary.
2 While pressing the SET button, press the POWER button.
3 Press the button of the component on the Commander that
you want to set up.
4 Press and release the CH+ button. Then press and release the
POWER button.
5 Repeat step 4 until the correct code number is found.
Each time you press the CH+ button and then the POWER
button, a new code number will be transmitted.
Keep trying until your component operates by receiving the
transmitted signal from the Commander (e.g., the power turns
off, the CH+ function works, playback starts, etc.) Be patient
as you do this; it may take about 70 tries until the correct code
number is located.
6 When the correct code is found, press the ENT button to store
the code number in the Commander's memory.
7 Check that the Commander is operating the other functions of
POWER
your component by pressing the corresponding buttons on
S
the Commander. If they seem to be working properly, you're
done setting up the Commander.
If the component does not operate properly, repeat steps 1 to 6
TV CBL
and search for another code.
If you still cannot get the Commander to work properly, see
"Troubleshooting."
0 5 6
Operating a Component
1 Press the button of the desired component on the
ENT
Commander.
TV CBL
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
See "Remote Button Descriptions" for complete descriptions of
the buttons on the Commander.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the
Commanders supplied with your components.
•Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to
the functions of the components themselves. For example, if
your TV does not have a MUTING function, the MUTING
button on this Commander will not function with your TV.
•Some functions of the component may not work with this
Commander.
•If your cable box can control volume, be sure to set its volume
switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your
TV's volume with the Commander.
Remote Button Descriptions
General
2 To mute the volume on TV.
MUTING TV/VIDEO
3 Volume up: +
VOL CH
Volume down: –
5 Component select buttons.
To switch to the operations
of each component, press
2
1 3
the button on which that
5
4 6 component is assigned.
6 To turn on and off the
8
7 9
power of the selected
0
RECALL ENT
component.
TV CBL
S
0 To set up the Commander,
press SET while pressing
POWER.
Operating a TV
Component code numbers /
7 Channel up: +
1 To change the input mode.
Números de código de componentes
4 To operate JUMP, FLASHBACK Channel down: –
8 and 9
or CHANNEL RETURN function
on the TV depending on the To change the channel. For
English
example, to change to channel
setting of the TV's
manufacturer. 5, press 0 and 5 (or press 5
TV
and ENT).
The left row of the table shows the brand, the right row shows
the code No.
Operating an analog cable box
CBL (Analog cable box)
4 To operate JUMP, FLASHBACK 8 and 9 The left row of the table shows the brand and the right row
or CHANNEL RETURN function. To change the channel. For shows the code No.
7 Channel up: + example, to change to channel 5,
Channel down: – press 0 and 5 (or press 5 and
Español
ENT).
TV (Televisores)
Notes
La fila izquierda de la tabla muestra la marca, la derecha el
•There may be cases you may turn on/off the cable box by
número de código.
pressing the CH+ or CH– buttons on the Commander.
CBL (adaptador para cable analógico)
•If your cable box can control volume, be sure to set its volume
La fila izquierda de la tabla muestra la marca y la derecha
control to a medium position. If the volume on the cable box is
muestra el número de código.
turned down completely, you will not be able to adjust your
TV's volume with the Commander.
To set a Component Code (see the instruction manual for details)
Para introducir un código de componente (si desea obtener más
Specifications
información, consulte el manual de instrucciones)
Operable distance Approx. 7 m (23 ft) (varies depending of
the component of each manufacturer)
Power requirements Two size AA (R6) batteries (not
supplied)
Battery life Approx. 6 months (varies depending on
While pressing the SET button, press the
frequency of use)
POWER button.
Dimensions Approx. 66 149 31 mm (w/h/d)
(2 5 / 5 7 / 1 1 / in.)
8 8 4 Mientras mantiene presionada la tecla SET,
Mass Approx. 91 g (3,2 oz.) (not including
presione la tecla POWER.
batteries)
Design and specifications are subject to change without notice.
The validity of the CE marking is restricted to only those
countries where it is legally enforced, mainly in the countries
EEA (European Economic Area).
Troubleshooting
If you have problems setting up or using the Commander:
• When setting up the Commander, carefully go through the
procedures described in "Setting the Code." If the code that's
listed first for your component doesn't work, try all the codes for
your component - in the order in which they're listed. If all the
codes fail to work (or if your component is not listed in this
Analog cable box/
manual), try using the procedures in "Searching for the Correct
Adaptador para cable analógico
Code."
• Check that you're aiming the Commander directly at the
Brand
component, and that there are no obstructions between the
Commander and the component. Hamlin/Regal
• Make sure the batteries you're using are not worn out, and that
Jerrold/G.I
they're inserted correctly.
• Check that the button of the TV or CBL is pressed to choose your
Oak
desired component.
Panasonic
• Check that the component has infrared remote capability. For
Pioneer
example, if your component didn't come with a remote
commander, it probably isn't capable of being controlled by a Scientific Atlanta
remote commander. Tocom
• Should any problem persist, reset the Commander to the factory
Zenith
setting by pressing the POWER, TV/VIDEO and VOL– buttons
simultaneously.
For the customers in the U.S.A.
Customer Support Information
If – after you've read through this manual – you still cannot get
the Remote Commander to work properly, call the Sony
Customer Support Helpline at 1-800-822-2217.
POWER
S
TV CBL
Code No.
ENT
Code No.
022, 023, 024, 025, 026
031, 001, 002, 003, 004, 005,
006, 007, 008, 018, 022, 032
027, 028, 029
019, 020, 021
014, 015
009, 010, 011
031, 016, 017
012, 013
Continued on reverse side
Continúa en el reverso