Subscribe to Our Youtube Channel
Related Manuals for Hettich LegaMove
Summary of Contents for Hettich LegaMove
- Page 1 Lifting column system for an electrically height-adjustable piece of furniture LegaMove...
-
Page 2: Preface
Date / Issue: 2018-09 If you have any questions, please contact Paul Hettich GmbH & Co. KG to discuss them before assembling the lifting column LegaMove. The installation and operating instructions are a separate part of the complete documentation. -
Page 3: Table Of Contents
7.1 Basic functions Table of Figures 7.1.1 Extending the lifting column system 1. Introduction 7.1.2 Retracting the LegaMove lifting column system 1.1 Explanation of the signs, symbols and labels used 7.2 Maual reset (homing) 1.2 Notes for the operator 7.3 Software-dependent functions 2. -
Page 4: Table Of Figures
Fig. 18. LegaMove Touch Inlay handset Fig. 19. Milling pattern for installing the LegaMove Touch Inlay handset with rubber flaps Fig. 20. Attaching the LegaMove Touch Inlay handset to the piece of furniture Fig. 21. Remote handset Basic Fig. 22. Inserting / replacing the battery Fig. -
Page 6: Introduction
1.1 Explanation of the signs, symbols and labels used These installation and operating instructions will help you become familiar with the LegaMove lifting column system and use it according to its intended applications. The safety notices used in this documentation have the following... -
Page 7: Notes For The Operator
Unless approved by the manufacturer of the LegaMove lifting column system, the operator may not make any additions, alterations or modifications to the system which may impair the system safety. -
Page 8: General Information
The lifting column system will loads. solely be loaded in pull direction. Therefore, the LegaMove lifting • Persons could incorrectly install the Lega- column system has been designed exclusively for this purpose. -
Page 9: Scope Of Delivery
The following components (incl. cabling) are available for the consequences. system: Fig. 2. LegaMove lifting column (here: retracted and extended) Fig. 3. Example of a handset and control unit Note Please refer to the Hettich catalog for other... -
Page 10: Safety
Never reach into moving parts! Always make sure that there are no persons in the danger zone before moving the piece of • Operate the LegaMove lifting column system furniture! when other persons and/or objects are within the danger zone. - Page 11 3. Safety The LegaMove lifting column system may not be put into service Observe the duty cycle of 10% of the LegaMove lifting column unless it is completely assembled and fully functional. system. Maintain a break of at least 18 minutes after each height adjustment (max.
-
Page 12: Safety Instructions For Maintenance Work
60dB(A). ry, have it regularly inspected by qualified personnel. Do not carry out repairs on the LegaMove lifting column system or its component by yourself. Maintenance may only be car- 3.4 Hazards from electrical energy ried out by the manu-facturer’s qualified personnel or under its... -
Page 13: Specific Danger Areas
3.6 Residual risks Ensure that no persons are within the vicinity of the piece of The LegaMove lifting column system has been built according to furniture when adjusting it. There is a risk of injury. the state of the art and recognized safety regulations. Neverthel-... -
Page 14: Training/Instruction
3. Safety Warning Residual hazards! Handling the LegaMove lifting column system still involves certain residual hazards that could not be eliminated by design. Be aware of any residual hazards and observe these installation and operating instructions as well as the documentation of the final product! -
Page 15: Description Of The Product
4. Description of the Product 4.1 Specifications Description: LegaMove lifting column system for an electrically height-adjustable piece of furniture in the private and commercial sector Type: LegaMove Place of installation: Closed rooms Min. height: approx. 575 mm Max. height: approx. 1,200 mm Max. -
Page 16: Controls
4.2.2 Control unit The following sections contain a description of the controls for Depending on the number of lifting columns required, the control the LegaMove lifting column system. units are available in two different variants. Note Observe the information provided in the “Scope 4.2.1 Power cords... -
Page 17: Handset
4. Description of the Product 4.2.3 Handset Remote handsets: The manually operated switch is used to control the lifting co- lumn system. Depending on the range of functions, the handset is available in three different versions. Note Fig. 10. Remote handset Basic Observe the information provided in the “Scope of delivery”... -
Page 18: Safeguards
4.3.1 Mechanical safeguards In addition the switch-off sensitivity is influ- Disconnect safeguards are installed on the LegaMove lifting co- enced by the mechanics, the motor and the lumn serve to protect the operator from mechanical dangers. The... -
Page 19: Transportation And Assembly
5. Transportation and Assembly 5.1 Transportation 5.2.1 Installing the lifting column Only move the LegaMove lifting column / piece of furniture when Securely mount the LegaMove lifting column firmly to the piece not connected to the power supply (power cord disconnected of furniture. -
Page 20: Installing The Control Unit
5. Transportation and Assembly 5.2.2 Installing the control unit 5. Then tighten the four screws of each LegaMove lifting column Note to max. 7Nm using the Allen wrench. Be sure to check that the control unit is suited 6. You can then assemble the piece of furniture. -
Page 21: Installing The Handset
• 2 screws, • Assembly instructions of the piece of furniture. Follow the steps described below to install the LegaMove Basic handset: 1. Follow the assembly instructions of the furniture manufactu- rer when installing the handset. 2. Unpack the handset. -
Page 22: Installing The Legamove Touch Inlay Handset
Fig. 18. LegaMove Touch Basic Inlay handset Attach the LegaMove Touch Basic Inlay handset in a suitable Fig. 20. Attaching the LegaMove Touch Basic Inlay handset to position in the piece of furniture. -
Page 23: Installing The Remote Handset Basic
5. Transportation and Assembly 5.2.3.3 Installing the remote handset Basic 4. Place the handset in the required position on the piece of fur- niture. Make sure that the handset is easily and conveniently accessible. 5. Attach the handset using two screws. Fig. -
Page 24: Commissioning
Commissioning covers any activity required to allow the height of the electrically height-adjustable piece of furniture to be ad- Warning justed using the LegaMove lifting column system. The following Attention! requirements must be met for commissioning: There is the risk of crushing from moving parts if •... -
Page 25: Initial Start-Up
8-pin motor / lifting column sockets (M1 to M3). • Check that the LegaMove lifting column system has been in- stalled in compliance with the regulations specified above! • Use the documentation of the furniture manufacturer to ensure that the piece of furniture is installed properly. -
Page 26: Programming The Remote Handset
6. Commissioning 6.2.2.1 Programming the remote handset 6.2.2.2 Replacing the battery The remove receiver must be programmed (taught) to be able to The remote pushbutton is energized by a lithium cell battery (CR understand the radiogram from the remote handset. The teach-in 2032, included). -
Page 27: Connecting Optional Components
The following figure shows the socket assignment for an example configuration. This sample configuration consists of: one control unit type LegaMove COMPACT-e-3 a piece of furniture with one LegaMove lifting column a handset, type LegaMove Basic The control unit is operative as soon as the pow-... -
Page 28: Operation
This function is designed to easily raise the position of the piece jerks. If this is not the case, disconnect the of furniture. The LegaMove lifting column system is extended power cord from the power grid and contact the during this process. After installing the LegaMove lifting column manufacturer’s customer service. -
Page 29: Retracting The Legamove Lifting Column System
7.2 Manual reset (homing) This function is designed to easily adjust the position of the piece If the actual position of the LegaMove lifting column system is no longer used with the position displayed or if an already configu- of furniture. The LegaMove lifting column system is retracted red control unit is used for another electrically height-adjustable during this process. -
Page 30: Software-Dependent Functions
These two features can be used to limit the travel range of the Note LegaMove lifting column system (and/or of the piece of furni- Before delivery, the control unit is parameterized ture), e.g. when an obstacle is located within the travel area. -
Page 31: Plug Detection
Despite the ISP collision detection there is a danger of crushing in as the combination of all If a LegaMove lifting column is missing or has been replaced, the components of the height-adjustable piece of control unit issues a triple click. In addition, the relevant error... -
Page 32: Resetting The Control Unit To Factory Defaults (Menu S0)
Keep pressing the desk top up button Note until the display shows S 0. If LegaMove lifting columns in a system are to be The display shows S 0. replaced, the control unit must first be reset to the factory defaults, and a manual reset must be Press the SAVE-button. -
Page 33: Cascading
7.3.8 Cascading a handset with display. In combination with multiple control units, cascading facilitates synchronous operation of up to twelve LegaMove lifting columns. Note Button Function It is necessary beforehand to specify with para-... -
Page 34: Troubleshooting
8. Troubleshooting 8.2.1 Possible malfunctions and their elimination Malfunctions of the LegaMove lifting column system may only be remedied by experts who have been assigned by the responsible person. LegaMove lifting columns do not work. Possible cause Remedy The entire environment of the LegaMove lifting column system... -
Page 35: Error Messages Shown On The Handset Display
Remedy the external short circuit. (Refer to section 6.2.2.1 “Program- ming”). Channel 2 faulty Connect the correct LegaMove lifting Bad connector contact Verify that the lifting column cable, column to the relevant socket. the power cord and the handset Channel 3 faulty Re-start the control unit. -
Page 36: Click Codes Of The Control Unit
8. Troubleshooting 8.2.3 Click codes of the control unit No Beschreibung Remedy As soon as power is supplied to the control unit, it uses the built- Synchronization Remove the load from the piece of in relay to inform the user with an acoustic signal (click) about of motor group 1 furniture. -
Page 37: Maintenance And Repair
Danger to life! Note Only qualified electricians may carry out mainte- If LegaMove lifting columns in a system are to be nance work on the electrical connections of the replaced, the control unit must first be reset to LegaMove lifting column system or the auxiliary the factory defaults (refer to section 7.3.7), and a... - Page 38 Non-compliance with the safety measures may lead to injuries. • Separately remove and store assemblies. The housings of LegaMove components must not be opened, removed or damaged. The following must be observed after completion Non-observance may lead to injuries! of the maintenance work: •...
-
Page 39: Inspecting The Safeguards
9. Maintenance and repair 9.2 Inspecting the safeguards Regularly inspect all safeguards for completeness and proper function. 9.3 Labeling, information signs The labeling / information signs must be • cleaned with a cloth • checked for tight fit and clear readability •... -
Page 40: Taking Out Of Service
10. Taking out of Service When the system is taken out of service, the power cord must be disconnected from the power supply. Danger Hazard due to electric shock! Work on electrical equipment may only be car- ried out by authorized and qualified specialists! -
Page 41: Disposal
Electric components should be disposed of as hazardous waste. When the LegaMove lifting column system is to be permanently taken out of service, the laws and regulations for its disposal in force at that time must be observed and followed. -
Page 42: Translation - Ec Declaration Of Incorporation
The national authorities may, if they so request, be provided with specific documents in paper or electric form. Note: The incomplete machine of type „LegaMove“ may only be commissioned when it has been established that a machine in which „LegaMove“ has been installed complies with the provisions of the machine directive. - Page 44 Paul Hettich GmbH & Co. KG Vahrenkampstr. 12-16 32278 Kirchlengern...
Need help?
Do you have a question about the LegaMove and is the answer not in the manual?
Questions and answers