Operating Instructions Owner’s Record The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.
– Consult the dealer or an experienced radio/TV ® is a U.S. CAUTION NERGY You are cautioned that any changes or modifications partner, Sony Corporation not expressly approved in this manual could void your authority to operate this equipment. ® NERGY Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that...
Table of Contents How to use this manual... 2 Getting Started Hooking up the system... 4 Setting the clock... 5 CD – Play Loading a disc ... 6 Playing a disc ... 6 — Normal Play/Shuffle Play Playing repeatedly... 7 —...
Getting Started Hooking up the system Perform the following procedures 1 to 3 to hook up your system using the supplied cords and accessories. Right speaker 1 Connect the speakers. Connect the right and left speaker cords to the SPEAKER terminals as shown below. AM loop antenna FM lead antenna 2 Connect the FM and AM antennas.
Inserting two R6 (size AA) batteries into the remote Note If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. When the remote no longer operates the system, replace both batteries with new ones.
CD – Play Loading a disc Press OPEN/CLOSE Z. Place a disc with the label side up on the disc tray. When you play a 8 cm disc, place it on the inner circle of the tray. Press OPEN/CLOSE Z again to close the disc tray.
Playing repeatedly — Repeat Play You can play all the tracks or a single track on a disc. Press REPEAT on the remote during playback until “REP” or “REP1” appears. REP: For all the tracks on the disc up to five times.
Other operations Do this Press ./> repeatedly Check the program order during program play. Cancel Program Press PLAY MODE on the Play remote in stop mode repeatedly until both “PGM” and “SHUF” disappear. Add a track to the Perform steps 1 – 4 in stop mode. end of the program Erase the program Press CLEAR on the remote in...
Page 9
Press ENTER. Repeat steps 1 through 5 to preset other stations. Press TUNING MODE to stop scanning. Manual tuning preset You can manually tune in and store the radio frequency of the desired stations. Press TUNER BAND repeatedly to select FM or AM. Press TUNING MODE repeatedly until “AUTO”...
Listening to the radio You can listen to a radio station either by selecting a preset station, or by manually tuning in the station. Use buttons on the remote for the operation. Listening to a preset station — Preset Tuning Preset radio stations in the tuner’s memory first (see “Presetting radio stations”...
Timer Falling asleep to music — Sleep Timer You can set the system to turn off after a certain time, so that you can fall asleep to music. Use buttons on the remote for the operation. Press SLEEP repeatedly. Each time you press the button, the minute display (the turn-off time) changes cyclically as follows: OFF t AUTO* t 90 t 80 t …...
Other operations Do this Change the setting Start over from step 1. 1 Press CLOCK/TIMER Check the setting/ activate the timer SELECT. 2 Press “DAILY” appears, then press ENTER. Cancel the timer 1 Press CLOCK/TIMER SELECT. 2 Press “OFF” appears, then press ENTER.
Adjusting the brightness of the display’s backlight You can change the brightness of the display’s backlight. Press DIMMER on the unit repeatedly. The backlight’s brightness changes cyclically. The brightness level is factory set at high. Viewing information about the disc in the display You can check the playing time and remaining time of the current track or that of the disc.
Optional Components Hooking up optional components To enhance your system, you can connect optional components. Refer to the operating instructions provided with each component. To the audio input jacks of an optional analog component Optional analog component A PC/MD/TAPE OUT jack Use an audio cord (not supplied) to connect an optional component (MD deck, etc.) to this jack.
CD player The disc tray does not open and “LOCK” appears in the display. • Consult your nearest Sony dealer or local authorized Sony service facility. The disc tray does not close. • Place the disc correctly in the center of the tray.
• Locate the antennas as far away from the speaker cords as possible. • Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand. • Try turning off surrounding electrical equipment. A stereo FM program cannot be received in stereo.
• When you move the system, take out any disc. If you have any questions or problems concerning your system, please consult your nearest Sony dealer. Notes on discs • Before playing, clean the disc with a cleaning cloth.
Note on CD-R/CD-RW playback Discs recorded on CD-R/CD-RW drives may not be played back because of scratches, dirt, recording condition or the drive’s characteristics. Besides, the discs, which are not yet finalized at the end of recording, cannot be played back. Music discs encoded with copyright protection technologies This product is designed to playback discs that...
Page 19
Inputs PC/MD/TAPE IN (stereo minijack): Sensitivity 250 mV, impedance 47 kilohms Outputs PC/MD/TAPE OUT (stereo minijack): Sensitivity 250 mV, impedance 1 kilohm PHONES (stereo minijack): Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 to 16 ohms.
List of button locations and reference pages How to use this page Use this page to find the location of buttons and other parts of the system that are mentioned in the text. Main unit ALPHABETICAL ORDER A – F DIMMER 1 (13) Display window 8 FUNCTION 2 (6, 7, 14, 16)
Need help?
Do you have a question about the CMT-CQ1 and is the answer not in the manual?
Questions and answers