Advertisement
F F . . 2 2
T T r r a a n n s s p p o o r r t t : : I I n n s s t t r r u u c c t t i i o o n n s s f f o o r r t t h h e e c c a a r r r r i i e e r r
I I M M P P O O R R T T A A N N T T
The transported load can shift:
• when braking;
• when accelerating;
• in corners;
• on rough roads.
F F . . 3 3
H H a a n n d d l l i i n n g g
Arrange a suitable area with flat floor for machine unloading
and storage operations.
F F . . 3 3 . . 1 1
P P r r o o c c e e d d u u r r e e s s f f o o r r h h a a n n d d l l i i n n g g o o p p e e r r a a t t i i o o n n s s
Before lifting:
• send all operators to a safe position and prevent persons
from entering the handling area;
• make sure the load is stable;
• make sure no material can fall during lifting. Manoeuvre
vertically in order to avoid impacts;
• handle the machine, keeping it at minimum height from the
ground.
For correct and safe lifting operations:
• use the type of equipment most suitable for characteristics
and capacity (e.g. electric pallet truck or lift truck);
• cover sharp edges;
G G
I I N N S S T T A A L L L L A A T T I I O O N N A A N N D D A A S S S S E E M M B B L L Y Y
W W A A R R N N I I N N G G
Refer to " Safety Information "
G G . . 1 1
I I n n t t r r o o d d u u c c t t i i o o n n
To ensure correct operation of the appliance and maintain safe
conditions during use, carefully follow the instructions given
below in this section.
C C A A U U T T I I O O N N
Keep the ventilation openings in the
appliance casing or in the installation
structure free of any obstructions.
G G . . 2 2
C C u u s s t t o o m m e e r r ' ' s s r r e e s s p p o o n n s s i i b b i i l l i i t t i i e e s s
The tasks and works required of the Customer are:
• arrange an earthed power socket of suitable capacity for the
input specified on the data plate;
• for information regarding the electrical connection, refer to
"G.7 Electrical connection ";
• check the floor planarity on which the machine is placed.
G G . . 3 3
A A p p p p l l i i a a n n c c e e s s p p a a c c e e l l i i m m i i t t s s
• A suitable space must be left around the appliance (for
operations, maintenance, etc.).
• The passages enabling personnel to operate on the
appliance must be at least 50 mm wide, except at the rear
of the appliance.
• This space must be increased in case of use and/or transfer
of other equipment and/or means or if exit routes are
necessary inside the workplace.
• In use to keep the correct distances indicated in the
installation diagram
18
• check the forks and lifting procedures according to the
instructions given on the packing.
F F . . 3 3 . . 2 2
S S h h i i f f t t i i n n g g
The operator must:
• have a general view of the path to be followed;
• stop the manoeuvre in case of hazardous situations.
F F . . 3 3 . . 3 3
P P l l a a c c i i n n g g t t h h e e l l o o a a d d
Before placing the load, make sure the way is free and that the
floor is flat and can take the load. Remove the appliance from
the wooden pallet, move it to one side, then slide it onto the
floor.
F F . . 4 4
S S t t o o r r a a g g e e
The machine and/or its parts must be stored and protected
from damp, in a non-aggressive place, free of vibrations and
with room temperatures between –10 ℃ [14 ℉] and 50 ℃ [122
℉].
The place where the machine is stored must have a flat
support surface to avoid deforming the machine or damage to
the support feet.
C C A A U U T T I I O O N N
Do not make modifications to the parts
supplied with the appliance. Any missing
or faulty parts must be replaced with
original parts.
G G . . 4 4
P P o o s s i i t t i i o o n n i i n n g g
C C A A U U T T I I O O N N
This appliance is not designed for built-in
installation.
The appliance must be levelled.
Do not obstruct the vent holes of the
appliance.
Wear protective gloves. Refer to "B.9 Personal protection
equipment " for further information.
Unpack the machine, carrying out the following operations:
• cut the straps and remove the protective film, taking care
not to scratch the surface if scissors or blades are used;
• remove the cardboard top, the polystyrene corners and the
vertical protection pieces.
Install the appliance, taking all the safety precautions required
for this type of operation, also respecting the relevant fire-
prevention instructions. Install the appliance in a ventilated
place. Refer to " Safety Information ".
Do not install the appliance adjacent to any high heat or grease
producing piece of appliance, such as a range top, griddle,
fryer, etc., that could allow radiant heat to raise the exterior
temperature of the appliance.
For the overall space required and connection dimensions,
refer to the installation diagrams given on the first pages of this
manual.
NOTE!
For appliances with stainless steel cabinet:
• remove the protective film very slowly without
tearing it, to avoid leaving glue stuck to the
surface;
• to remove the traces of glue, use a non-corrosive
solvent, rinsing it off and drying thoroughly;
• it is advisable to go over all the stainless steel
surfaces with a rag soaked in paraffin oil in order
to create a protective film.
Advertisement
