About The Indications In The Display - Sony STR-DA2000ES Operating Instructions (primary manual) Operating Instructions Manual

About the indications in the display

1 2
SLEEP SP.A SP.B
SW
L.F.E.
SBL
qk
A SW: Lights up when sub woofer selection is
set to "YES" (page 20). While this indicator
lights up, the receiver outputs the LFE signal
recorded on the disc or generates a low
frequency signal for output to the sub woofer.
This indicator does not light during the 2CH
STEREO mode.
B SLEEP: Lights up when sleep timer is
activated.
C SPA/SPB: Lights up in accordance with the
speaker system being used (A or B). Turns off
when headphones are connected.
D MULTI CH IN 1/2: Lights up when "MULTI
1 DIRECT" or "MULTI 2 DIRECT" is
selected.
E ; DIGITAL (EX): Lights up when Dolby
Digital signals are input. "EX" lights up when
Dolby Digital EX signals are input.When
playing a Dolby Digital EX format disc, be
sure that you have made digital connections
and that INPUT MODE is NOT set to
"ANALOG FIXED" (page 38).
F ; PRO LOGIC (II): Lights up when the
receiver applies Pro Logic processing to 2
channel signals in order to output the center
and surround channel signals. This indicator
also lights when the Pro Logic II Movie/Music
decoder is activated. However, this indicator
does not light if both the center and surround
speakers are set to "NO".
G DTS (-ES): Lights up when DTS signals are
input. "-ES" lights up when DTS-ES signals
are input. When playing a DTS format disc, be
sure that you have made digital connections
and that INPUT MODE is NOT set to
"ANALOG FIXED" (page 38).
GB
30
3 4
MULTI CH IN 1 2
L C R
SL S SR
SB SBR
qj
5 6
; ;
DIGITAL EX PRO LOGIC II
D.RANGE
qh
H 96/24: Lights up when the receiver is
I Tuner indicators: Lights up when using the
J MEMORY: Lights up when presetting
K D.ASSIGN: Lights up when the digital assign
L COAX: Lights up when the source signal is a
M OPT: Lights up when the source signal is a
N NEO:6: Lights up when DTS Neo:6 Cinema/
O EQ: Lights up when the equalizer is activated.
P D.RANGE: Lights up when dynamic range
Q Playback channel indicators: The letters
7 8
DTS -ES 96/24
EQ
NEO:6
qg qf
decoding DTS 96 kHz/24 bit signals.
receiver to tune in radio stations, etc. See
pages 25–28 for tuner operations.
stations, naming preset stations and inputs, etc.
function is used for the selected input.
digital signal being input through the
COAXIAL terminal or when INPUT MODE
is set to "COAXIAL FIXED" (page 38).
digital signal being input through the
OPTICAL terminal, or when INPUT MODE
is set to "OPTICAL FIXED" (page 38).
Music decoding is activated. However, this
indicator does not light if both the center and
surround speakers are set to "NO".
compression is activated (page 43).
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the receiver downmixes the
source sound (based on the speakers settings).
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing)), SBL (Surround back
Left), SBR (Surround back right), SB
9 q;
MONO MEMORY
RDS
STEREO
OPT
COAX
D.ASSIGN
qd qs qa