Burkert 2060 Quick Start Manual
2/2-way angle seat valve, 2/2-way globe valve
Hide thumbs
Also See for 2060:
- Quick start manual (46 pages) ,
- Operating instructions manual (31 pages) ,
- Installation instructions manual (28 pages)
Subscribe to Our Youtube Channel
Related Manuals for Burkert 2060
Summary of Contents for Burkert 2060
- Page 1 Type 2060, 2061 2/2-way angle seat valve, 2/2-way globe valve 2/2-Wege-Schrägsitzventil, 2/2-Wege Geradsitzventil Vanne à siège incliné 2/2 voies, Vanne à siège droit 2/2 voies Quickstart English Deutsch Français...
- Page 2 We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. © Bürkert Werke GmbH & Co. KG, 20 - 2017 Operating Instructions 1706/ / Original DE...
-
Page 3: Table Of Contents
The operating instructions can be found on the Internet at: 11 packaGinG, transport, storaGe .......... 15 www.burkert.com Definition of term The term “device” used in these instructions always stands for the angle seat valve Type 2060 or globe valve 2061. english... -
Page 4: Symbols
Type 2060, 2061 Symbols symbols auThorizeD use Danger! non-authorized use of the types 2060 and 2061 may be a hazard to people, nearby equipment and the environment. warns of an immediate danger. ▶ The device is designed for the controlled flow of liquid and gas- ▶ Failure to observe the warning may result in a fatal or serious injury. eous media. -
Page 5: Basic Safety Instructions
Type 2060, 2061 Basic safety instructions basic safeTy insTrucTions General hazardous situations. These safety instructions do not consider any contingencies or incidents To prevent injury, ensure: which occur during installation, operation and maintenance. ▶ Secure system against unintentional activation. The operator is responsible for observing the location-specific safety ▶... -
Page 6: General Information
General information General informaTion Technical DaTa contact address conformity germany Type 2060 and 2061 conforms with the EC Directives according to the EC Declaration of Conformity (if applicable) . Bürkert Fluid Control Systems Sales Center standards Chr.-Bürkert-Str. 13-17 D-74653 Ingelfingen The applied standards, which verify conformity with the EC Direc- Tel. - Page 7 Body material Type (at 150 °C > Tmed < ø 130 mm 180 °C) Flow 1 2060 A 25,0 PTFE VA Tab. 1: Temperature ranges Body orifice D33.7 Pmed 16bar Pilot 5.0-10bar The angle seat valve is suitable for steam sterilization.
- Page 8 Type 2060, 2061 Technical data minimum pilot pressure: flow direction below the seat General technical data (medium flow against the closing direction of the valve) media Required minimum pilot pressure P with control function A: Control medium Neutral gases, air Actuator size Flow media Water, alcohol, fuel, hydraulic liquids,...
-
Page 9: Installation
Numbers for indicating the Flats for open-end • Ensure the lines are flush. direction of flow wrench • Clean pipelines (sealing material, swarf, etc.). • Observe direction of flow (see type label). Fig. 2: Angle seat valve, Type 2060 english... - Page 10 Type 2060, 2061 Installation installation of the valve body install actuator (welded body) Warning! risk of injury from improper installation. Graphite seal ▶ Installation may only be performed by qualified and trained personnel. ▶ For installation use an open-end wrench. ▶ Observe the tightening torque.
- Page 11 Type 2060, 2061 Installation → mount accessories Screw actuator into the valve body. Observe tightening torque (see “Tab. 5”). For description, refer to documentation of corresponding accessories. Pilot air port CFB, CFI rotating the actuator Air discharge connection CFA The position of the connections can be aligned steplessly by rotating the actuator through 360°.
- Page 12 Type 2060, 2061 Installation → control function i: Counter on the flats of the nipple with a suitable open-end → wrench. Connect the control medium to the pilot air port 1 and 2 of the → Place suitable open-end wrench on the hexagon of the actuator.
-
Page 13: Start-Up
Type 2060, 2061 Start-up sTarT-uP flow direction Warning! 8.2.1 angle seat valve risk of injury from improper operation. Improper operation may result in injuries as well as damage to the device and the area around it. ▶ Before start-up, ensure that the operating personnel are familiar with and completely understand the contents of the operating instructions. -
Page 14: Maintenance Work
Type 2060, 2061 Maintenance work 8.2.3 flow direction above the seat mainTenance Work → Control function A, CFA: closes by spring force against the medium Complete a visual inspection of the equipment once a year. Shorter flow. Control function B, CFB: closes with the control pressure against maintenance intervals may be recommended depending on the the medium flow. -
Page 15: Removal
Type 2060, 2061 Removal PackaGinG, TransPorT, removal sToraGe Danger! note! risk of injury from discharge of medium and pressure! transport and storage damage. It is dangerous to remove a device which is under pressure due to ▶ Protect the device against moisture and dirt in shock-resistant the sudden release of pressure or discharge of medium. - Page 16 Type 2060, 2061 english...
- Page 18 www.burkert.com...
Need help?
Do you have a question about the 2060 and is the answer not in the manual?
Questions and answers