CX86/VPL-CX80) (on the CD-ROM) (this manual) This Operating Instructions describes the setup and operations of this unit. Model VPL-CX86 is used for illustration purposes throughout this manual. Any differences in operation are indicated in the text, for example, “VPL-CX86 only.”...
Features High brightness, high picture quality High brightness Adopting Sony's unique optical system provides a high-efficiency optical system. It allows the 190 W UHP lamp to give a light output of 3000 ANSI lumen. High picture quality Three super-high-aperture 0.79-inch XGA panels with approximately 790,000 effective pixels, produce a resolution of 1024 ×...
Page 5
• Display Data Channel is a trademark of the Video Electronics Standard Association. • “Memory Stick” and trademarks of Sony Corporation. • Air Shot is a trademark of Sony Corporation. • Side Shot is a trademark of Sony Corporation. Features...
The lens protector opens automatically when the power is turned on. c Powered tilt adjuster d Front remote control detector e Ventilation holes (exhaust) f Access lamp (VPL-CX86 only) Lights during access to the “Memory Stick”. Location and Function of Controls Note Do not remove the “Memory Stick”...
n Ventilation holes (intake)/Lamp cover o Ventilation holes (intake)/Air filter cover Notes • Do not place anything near the ventilation holes as this may cause internal heat build-up. • Do not place your hand near the ventilation holes as this may cause injury.
power is turned off with the ?/1 key. The fan runs for about 60 seconds after the power is turned off. For details, see page 19. c INPUT key d TILT adjustment key For details, see “Projecting” on page 16. e MENU key Displays the on-screen menu.
AUDIO connector which is common for INPUT A/B is output. When the “Memory Stick” is selected in Input-C (VPL-CX86 only), the sound saved in the “Memory Stick” is output. When “Air Shot” is selected, no sound is output.
FREEZE key Freezes the projected picture. To cancel the frozen picture, press the key again. g AIR SHOT key (VPL-CX86 only) Displays the Air Shot Home. When the input signal is other than from Air Shot, it switches to Air Shot.
Page 11
l RESET/ESCAPE key Functions as a RESET key. Resets the value of an item to its factory preset value or returns the enlarged image to its original size. This key functions when the menu or a setting item is displayed on the screen. m D ZOOM (Digital Zoom) +/–...
Presentation Tool (VPL-CX86 only) You can use a laser pointer or control a presentation file made using Microsoft PowerPoint when projecting a picture using the Air Shot feature. a Laser transmitter b LASER key A laser beam is emitted from the laser transmitter while you keep this key pressed.
B Projecting the Picture Installing the Projector The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide. Screen Distance between the screen and the center of the lens Screen size (inches) Minimum...
Connecting the Projector When you connect the projector, make sure to: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals.
• A inserted into the “Memory Stick” slot on the projector cannot be accessed from the Projector Station for Presentation (VPL-CX86 only). Connecting a VCR This section describes how to connect the projector to a VCR. For more information, refer to the instruction manuals of the equipment you are connecting.
To connect to a video GBR/ Component output connector Right side audio to video output GBR/ component output A Stereo audio connecting cable (not supplied) (Use a no-resistance cable.) B SMF-402 Signal Cable (not supplied) HD D-sub 15-pin (male) ↔ 3 × phono jack Notes •...
Page 17
Note When the projector is turned on, the Startup screen is projected (VPL-CX86 only). For details, see the attached “Operating Instructions for “Memory Stick”” stored on the CD-ROM. Turn on the equipment connected to the projector. Press the INPUT key to select the input source.
Page 18
to lower the to raise the projector projector TILT adjustment key Powered tilt adjuster Notes • When you adjust the powered tilt adjuster with the TILT key, the V keystone adjustment is performed at the same time. If you do not want to perform the automatic keystone adjustment, set the V Keystone menu to “Manual.”...
Turning Off the Power Press the ?/1 key. “POWER OFF? Please press ?/1 key again.” appears to confirm that you want to turn off the power. Note The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds.
B Convenient Functions Selecting the Menu Language You can select one of fifteen languages for displaying the menu and other on-screen displays. The factory setting is English. To change the menu language, proceed as follows: ON/STANDBY indicator Plug the AC power cord into a wall outlet.
To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. Security Lock The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password.
Page 22
Enter the password on this screen. Enter new password key. Power-on cannot be performed without the password. Use: Enter the password again to confirm. Re-enter new password key. Be sure to remember this password. Use: When the following message is displayed, the setting for security lock is completed.
Controlling the Computer Using the Supplied Presentation Tool (When Using the Air Shot) (VPL-CX86 only) When you are using the Air Shot to project the picture from a computer, you can perform some operations for a slide show using the supplied presentation tool.
powered tilt adjuster extended may damage the adjuster. • Turn off the projector according to the procedure explained in “Turning Off the Power,” then cool it down before storing the projector in the carrying case. Direct Power On/Off Function If you will be using a circuit breaker to turn the power for the entire system on and off, set the direct power on function to “On.”...
Input signal setting indicator For Input-A: Shows “Computer,” “Component,” or “Video GBR.” For Input-C: Shows “Air Shot” or “Memory Stick” (VPL-CX86 only) For Video/S-Video input: Shows “Auto” or the “Color System” setting on the SET SETTING menu. Press the MENU key.
Page 26
To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. To reset items that have been adjusted Select the item that you want to reset, and then pres the RESET key on the Remote Commander.
The PICTURE SETTING Menu The PICTURE SETTING menu is used for adjusting the picture or volume. Items that can be adjusted or set depend on the kind of input signals. For details, see “Input signals and adjustable/setting items” on page 36. PICTURE SETTING Input A P i c t u r e M o d e...
The INPUT SETTING Menu The INPUT SETTING menu is used to adjust the input signal. Items that can be adjusted or set depend on the kind of input signals. For details, see “Input signals and adjustable/setting items” on page 36. When the video signal is input Setting items Functions...
“Shift.” Signal Memory No. SIZE Super Mac-2 SGI-1 Macintosh 19" Macintosh 21" Sony News PC-9821 1280 × 1024 WS Sunmicro Note When the aspect ratio of input signal is other than 4:3, a part of the screen is displayed in black.
(only when “startup” in “Memory Stick” Home is set to “Off” (VPL-CX86 only)) or the INPUT key is pressed. Input-A Signal Sel. Selects the “Computer,” “Component,” or “Video GBR” signal input via the INPUT A connector.
Page 31
• Front: Activates the front detector only. • Rear: Activates the rear detector only. Illumination Selects whether the SONY logo on the top panel of the projector lights when the projector is on. Normally, this setting is “On.” Panel Key Lock...
The MENU SETTING Menu The MENU SETTING menu is used for changing the menu displays. Setting items Functions Status (on-screen Sets up the on-screen display. display) When set to “Off,” turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages.
The INSTALL SETTING Menu The INSTALL SETTING menu is used for changing the settings of the projector. Setting items Functions Tilt... Adjusts the position (height) of the projected picture. V Keystone Corrects the trapezoidal distortion caused by the projection angle. Select “Auto” for automatic correction, or “Manual”...
Page 34
Setting items Functions Direct Power On Set to “On” if you are using a circuit breaker to turn the power on/off the entire system. You can turn off the power just by unplugging the power cord without pressing the ?/1 key.
The INFORMATION Menu The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp. INFORMATION I n p u t A V P L - C X 8 6 Serial No.
Page 36
Sharpness Gamma Mode Color Temp. Volume z : Adjustable/can be set – : Not adjustable/cannot be set : Preset memory No. 3, 4 only : VPL-CX86 only INPUT SETTING menu Item Video or S- Video (Y/C) Adjust Signal... Dot Phase...
B Maintenance Replacing the Lamp The lamp used as a light source is a consumable product. Thus replace this lamp with a new one in the following cases. • When the lamp has burnt out or dims • “Please replace the Lamp.” appears on the screen •...
Page 38
Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (b). Fold down the handle to replace it (c). Notes • Be careful not to touch the glass surface of the lamp. •...
Cleaning the Air Filter The air filter should be cleaned every 1000 hours. Remove dust from the outside of the ventilation holes with a vacuum cleaner. 1000 hours are approximate. This value varies depending on the environment or how the projector is used. When it becomes difficult to remove the dust from the filter with a vacuum cleaner, remove the air filter and wash it.
The electrical system has broken down. c Consult with qualified Sony personnel. If it is necessary to use the projector in case of emergency, slide the lens protector open by hand, and then press the ?/1 key. You can now use the projector.
Page 41
• The picture is muted. c Press the PIC MUTING key to release the picture muting (see • The B key is activated (VPL-CX86 only). c Press the B key on the Presentation Tool to deactivate the key • The computer signal is not set to output to an external monitor or set to output both to an external monitor and a LCD monitor of a computer.
Page 42
• The USB cable is not connected. c Connect the projector to the computer using the USB cable. • You are operating the Air Shot (VPL-CX86 only). c When using the Air Shot, the computer cannot be controlled with the Remote Commander.
Page 43
• The lens protector did not open due to a problem. c In case of emergency, slide the lens protector open by hand, and c If this problem occurs again, consult with qualified Sony • The electrical system may have broken down.
Messages List Warning Messages Use the list below to check the meaning of the messages displayed on the screen. Message High temp.! Probably use in high altitude. Switch to high altitude mode on? Yes V No v High temp.! Lamp off in 1 min.
Specifications Optical characteristics Projection system 3 LCD panels, 1 lens, projection system LCD panel 0.79-inch XGA panel, about 2,360,000 pixels (786,432 pixels × 3) Lens 1.2 times zoom lens (powered) f 23.5 to 28.2 mm/F1.6 to 1.78 Lamp 190 W UHP Projected picture size 40 to 300 inches (measured diagonally)
Page 46
Vp-p high impedance, positive/ negative VD: Vertical sync input: 1 - 5 Vp-p high impedance, positive/ negative Up (female) × 1 Wireless LAN card slot (VPL-CX86 only) × 1 “Memory Stick” slot (VPL-CX86 only) × 1 OUTPUT MONITOR OUT: HD D-sub 15-...
Page 47
Signal Cable SMF-402 (HD D-sub 15-pin (male) y 3 × phono type (male)) Some of the items may not be available in some areas. For details, please consult your nearest Sony dealer. Pin assignment INPUT A connector (HD D-sub 15-pin, female) R/R-Y...
Warning on power connection Use the supplied power cord when you use the projector in your country/region. Otherwise, use a proper power cord meeting the following specifications. The United States, Canada Plug type VM0233 Female end VM0089 Cord type Rated Voltage & 10A/125V Current Safety approval...
Installation Diagram Floor Installation (Front Projection) Wall Center of the screen This section describes the examples of installing the projector on a desk, etc. See the chart on page 52 concerning the installation measurements. The alphabetical letters in the illustration indicate the distances below. a: distance between the screen and the center of the lens b: distance between the floor and the center of the lens c: distance between the floor and the bottom of the adjusters of the projector...
Page 52
1160 1760 2360 (93) M 1350 2040 2740 (108) x-237 x-356 x-474 (x-9 (x-14) (x-18 x-299 x-417 x-536 (x-11 (x-16 (x-21 a (N) = {(SS × 23.177/0.7874)–50.4} × 1.025 a (M) = {(SS × 28.177/0.7874)–50.4} × 0.975 b = x–(SS/0.7874 × 4.667) c = x–(SS/0.7874 ×...
Page 53
When installing the projector on the ceiling, use a Projector Suspension Support recommended by Sony. For ceiling installation, ask for qualified Sony personnel. See the chart on page 54 concerning the installation measurements. The alphabetical letters in the illustrations indicate the distances below.
Page 54
a’ N 1260 1860 2470 M 1450 2140 2840 (111 b+293 b+411 b+530 (b+11 (b+16 (b+20 a’(N) = {(SS × 23.177/0.7874)+51.4} × 1.025 a’(M) = {(SS × 28.177/0.7874)+51.4} × 0.975 x = b + (SS/0.7874 × 4.667+55.8) The installation measurements and their calculation method for each lens are shown above. The alphabetical letters in the charts and calculation methods indicate the following.
“Side Shot” and “V Keystone” Adjustments With “Side Shot” (horizontal keystone adjustment) provided for the projector, you can project the picture from the side of the screen. When projecting with “Side Shot” adjustment only, you can adjust the horizontal distortion of the screen to the maximum using “Side Shot.”...
Page 56
Video/60, Video/50, 480/60i, 575/50i, 480/60p, 575/50p 1080/60i, 1080/50i, 540/60p 720/60p, 720/50p PC, Air Shot (VPL-CX86 only), “Memory Stick” (VPL-CX86 only) Notes • If “V Keystone” is set to “Auto,” the “Side Shot” adjustment area may be narrow. • “V Keystone” on the INSTALL SETTING menu is set to “Auto” at the factory, and the vertical distortion of the picture is automatically corrected.
Dimensions Front Center of the lens Right side Center of the projector Hole for security lock Remote control detector Center of the lens Unit: mm (inches) Dimensions...
Page 58
Left side Bottom Center of the lens Holes for mounting a projector suspension support Dimensions Projector suspension support mounting surface Center of the projector Center of gravity of the projector Unit: mm (inches)
Index Adjusting memory of the settings ...26 the picture ...27 the picture size/shift ...28, 29 Air filter ...39 Auto Input Search ...30 Background ...33 Batteries ...11, 12 Brightness ...27 Color ...27 Color System ...30 Color Temp..27 Connecting a computer ...14 Connecting a VCR ...15 Contrast ...27 Digital Zoom function ...24...
Page 60
Remote Commander ... 10 front remote control detector ... 6 location and function of controls ... 10 rear remote control detector ... 6 Reset resettable items ... 26 resetting an item ... 26 Scan Converter ... 29 Screen size ... 13, 45 Security Lock ...