Sony SRS-RF930RK Operating Instructions

2-663-019-12(1)
Wireless Stereo
Speaker System
Operating Instructions
Mode d'emploi
Manual de instrucciones
Owner's Record
The model number is located at the bottom of the transmitter and the rear of
the speaker system.
The serial number is located at the bottom of the transmitter and the speaker
system.
Record these numbers in the spaces provided below. Refer to them whenever
you call upon your Sony dealer regarding this product.
Model No.
Transmitter TMR-930
Speaker system SRS-RF930R
Serial No.
Transmitter
Speaker system
SRS-RF930RK
© 2005 Sony Corporation
Printed in Malaysia
English
WARNING Welcome!
To reduce the risk of fire or electric shock, do
Thank you for purchasing the Sony
not expose this apparatus to rain or moisture.
SRS-RF930RK Wireless Stereo Speaker System.
To avoid electrical shock, do not open the
Before operating the unit, please read this manual
cabinet. Refer servicing to qualified personnel
thoroughly and retain it for future reference.
only.
Some features are:
Information •Wireless system that allows you to use your
You are cautioned that any changes or modifications
system free from the restriction of speaker cords.
not expressly approved in this manual could void
Wide signal reception range up to about 150 feet
your authority to operate this equipment.
(46 m).
•This speaker system can be powered with built-
For the Customers in the U.S.A.
in rechargeable battery for perfect wireless
If you have any questions about this product, you
speaker system.
may call;
Sony Customer Information Services Center •Smart battery charge system on transmitter.
1-800-222-7669 or http://www.sony.com/ •One-box stereo type speaker for easy to carry and
setting in any room or anywhere.
Declaration of Conformity •2 inputs on transmitter for connecting PC and
Trade Name: SONY other audio equipments.
Model No.: SRS-RF930R •1 analog input on main unit to connect directly
Responsible Party: Sony Electronics Inc.
other portable audio equipment.
Address: 16530 Via Esprillo,
•Manual tuning function available on speaker.
San Diego, CA 92127 USA
Telephone No.: 858-942-2230
Notes on receiving
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
performance
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including The system for this equipment utilizes very high
interference that may cause undesired operation.
frequency signals in the 900 MHz band so the
receiving performance may deteriorate due to the
For the Customers in Canada surroundings. The following examples illustrate
Operation is subject to the following two conditions that may reduce the possible receiving
conditions: (1) this device may not cause range or cause interference with reception.
• Inside a building with walls containing steel
interference, and (2) this device must accept any
beams.
interference, including interference that may cause
• Area with many steel file cabinets, etc.
undesired operation of the device.
• Area with many electrical appliances capable of
For the customers in the USA and Canada generating electromagnetic noise.
• Transmitter is placed on a metal instrument.
• Area facing roadways.
RECYCLING NICKEL METAL HYDRIDE
• Noise or interfering signals exist in the
BATTERIES
surroundings due to radio transceivers in trucks,
etc.
Nickel Metal Hydride
• Noise or interfering signals exist in the
batteries are recyclable.
surroundings due to wireless communication
You can help preserve our
systems installed along roadways.
environment by returning
• Transmitter is placed directly on floor.
your used rechargeable
Placing it up off the floor, such as on a desk, is
batteries to the collection and
recommended.
recycling location nearest you.
N Getting started
For more information regarding recycling of
rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/ Unpacking
Caution: Do not handle damaged or leaking
Check that you have the following items:
Nickel Metal Hydride batteries.
• The speaker system
• The transmitter
• AC power adaptor
Hooking up the system Charging the speaker
system battery
Connecting the transmitter to audio/
video equipment
Rest the speaker system on the transmitter so that
the speaker system's contact pins meet the
Set the transmitter by the following steps. Select
transmitter's contact points while making sure that
the hookup depending on the jack type of the
the CHARGE indicator lights in green.
audio/video equipment you want to connect the
transmitter to. Speaker system
A To connect to LINE OUT, REC OUT or
headphones jack
Transmitter
POWER CHARGE
to an AC
OFF ON B A DC IN 9V 1 2 3 outlet Transmitter
NOISE FILTER AUDIO IN CHANNEL
to AUDIO IN AUDIO IN A
B jack
POWER CHARGE
to an AC
outlet
Connecting Audio cord
cord (AUDIO IN A)
(not supplied)
Contact pin
Contact
Right
point
to
Left channel channel
headphones
(white) (red)
or LINE OUT
Notes
to LINE OUT jack (stereo
• While charging the battery, turn off the speaker system.
or REC OUT mini jack)
• Charging is completed in about 16 hours, and the
jacks
CHARGE indicator goes off.
• Charge the rechargeable battery within a temperature of
0 ˚C to 35 ˚C (32 ˚F to 95 ˚F).
• Do not turn on the speaker system while charging the
rechargeable battery. Otherwise, the battery will not be
Stereo system, PC, etc.
fully charged.
VCR, etc. • Do not remove the speaker system from the transmitter
until charging is finished.
B To connect to TV, etc.
• If you remove the speaker system from the transmitter
If noise occurs when the transmitter is and replace, charging will take longer.
connected to the headphone jack of your • If you remove the speaker system from the transmitter
by accident and replace within 5 seconds, charging time
TV or VCR, set the NOISE FILTER switch
will not be affected.
to ON.
• If you charge the speaker system again after the
CHARGE indicator goes off, remove it from the
transmitter and replace after about 15 seconds.
Transmitter
• To prolong the life of the rechargeable battery, charge it
only after it has been completely used up.
• The life of the built-in rechargeable battery is about 3
years. But it differs depending on operating conditions.
N Operating the system
OFF ON B A DC IN 9V 1 2 3
AUDIO IN CHANNEL
NOISE FILTER
Listening to a program
AUDIO IN A
Before using the speaker system, charge the built-
in rechargeable battery first.
Turn down the volume of the speaker system
Audio cord
before playing back a program on the connected
(AUDIO IN A)
audio/video equipment.
Listening to a program from the
transmitter by wireless transmission
to headphones or
LINE OUT jack
(stereo mini jack)
TUNE dial
TV, etc.
POWER switch AUDIO IN
Notes
• If you connect the transmitter to LINE OUT or REC
POWER indicator VOLUME control
OUT jack, do not set the NOISE FILTER switch to ON.
Otherwise, the volume will be limited. 1
First turn on the audio/video equipment
• The NOISE FILTER switch is effective only in case of
connection using AUDIO IN A.
and start playing.
• When the transmitter is placed on or near a TV, it may
The POWER indicator of the transmitter
pick up a noise. In such case, place the transmitter away
from the TV. will light up.
• When you connect the connecting cord directly to an
2
earphone jack, the audio signal will not be output
Turn on the speaker system.
through the right channel. In such a case, use the
separately sold PC-236MS plug adaptor. The POWER indicator of the speaker
• If the connected equipment has the AVLS (Automatic
system will light in red.
Volume Limiter System) function, be sure to turn the
function off when using the transmitter. Otherwise, you
3
Select the radio frequency with the
will have to turn up the volume of the speaker system,
and that may cause noise. CHANNEL selector.
• If the connected equipment has the BASS BOOST or
MEGA BASS function, be sure to turn the function off
when using the transmitter. Otherwise, the sound from
the speaker system may be distorted.
• Do not place the transmitter near a fluorescent lamp, etc.
when using the system. 1 2 3
CHANNEL
Connecting the transmitter to an AC
outlet using the supplied AC power
Note
adaptor
If you use the unit near a cordless telephone, it may
cause radio interference. If poor reception occurs, try
another channel using the CHANNEL selector.
Transmitter
4
Use the TUNE dial to adjust the tuning
To DC IN
of the speaker system.
9 V jack
Use the VOL control to adjust the
volume.
to an AC
outlet
AC power adaptor Notes
(supplied: AC-S901) • When the POWER indicator of the speaker system does
not light up, or if it turns off immediately, charge the
Note
rechargeable battery.
Use only the supplied AC power adaptor. Do not use any
• Do not place the transmitter and the speaker system
other AC power adaptor to avoid damaging the
near any metal instrument. Otherwise, the receiving
transmitter.
range from the transmitter may be reduced.
Polarity of the plug
2
Listening to another audio device Open the cabinet of the speaker system
connected to the speaker system and remove the rechargeable battery as
You can use this speaker system to listen to a illustrated.
connected CD/MD WALKMAN, etc. by
connecting to the AUDIO IN jack using the
Battery
separately sold RK-G136 connecting cord.
Hard Drive Player, Flash Memory
Player, Discman, MD, WALKMAN* etc.
to headphones, LINE OUT
or REC OUT jack
(stereo mini jack)
N Additional information
Connecting cord
Precautions
(not supplied)
Notes on the AC power adaptor
•Plug the AC power adaptor into a nearby AC
output. In case of a problem, unplug from the AC
outlet immediately.
•Do not place the AC power adaptor on a
to AUDIO IN jack
bookshelf or in a confined place such as a cabinet.
•Do not use the AC power adaptor in a place
subject to liquid or moisture to avoid fire or
electric shock. Furthermore, do not place liquid-
filled vessels, such as a vase, etc., on the AC
power adaptor.
•When the transmitter is not to be used for a long
Speaker system period of time, disconnect the AC power adaptor
from the AC outlet holding the plug. Do not pull
Notes
on the cord.
• When you use the speaker system, remove it from the
transmitter.
Notes on the location you set the speaker
• Do not use the speaker system while charging the
system
rechargeable battery. Otherwise, the battery life may be
• Do not leave the wireless speaker system in a
shortened.
location subject to:
* "WALKMAN" is a registered trademark of Sony – Direct sunlight or extremely high temperature such
Corporation to represent Headphone Stereo products. as near a heater or in a car with its windows closed.
– High humidity such as in a bathroom.
– Excessive dust or sandy places.
Sending RF signals from the transmitter
• The speaker system is magnetically shielded, but
The transmitter starts sending the RF signals
do not put a recorded tape, watch, cash card or
automatically, when it detects audio signals from
floppy disk in front of the speaker system.
the equipment connected.
• Set up the speaker system on a flat surface.
If it does not detect an audio signal for more than
approximately four minutes, the transmitter will
Notes on charging the battery
stop sending RF signals, and the POWER indicator
• When you charge the rechargeable battery, use
turns off.
the supplied transmitter only.
When the transmitter receives an audio signal
• The charging time differs depending on usage
again, it starts sending the RF signals, and the
conditions of the battery.
POWER indicator will light in red again.
• When you use the battery for the first time or the
If the audio signal is very weak, the transmitter
battery has not been used for a long time, the
does not send RF signals. If the transmitter is
battery duration time may become shorter than
connected to a headphone jack, make sure the
the usual duration time. However, after you
volume of the equipment connected is set to 5 – 6
charge the battery several times, the battery
or higher.
duration time returns to its normal condition.
You may not hear the beginning of the sound from
• If the battery duration time becomes half of its
the speaker system until the transmitter starts
normal time even after the battery is charged
sending the RF signals after detecting an audio
fully, the battery is worn out. In this case,
signal.
consult your nearest Sony dealer.
Notes
Notes on using the speaker system
• If the transmitter is connected to the headphones jack of
• Do not disassemble the speaker unit, built-in
the source equipment, set the volume of that equipment
amplifier or cabinet.
as high as possible without distorting the audio signal.
• Do not insert an object into the jack. Doing so
• If a hissing noise is heard, move it closer to the
may cause a malfunction.
transmitter.
• If you hold the antenna of the transmitter with your • Keep the volume at a moderate level to prevent
hand, noise may occur. But this is not a malfunction. distortion.
• Do not touch the contact points of the
The effective areas of the transmitter
transmitter or the contact pins of the speaker
The optimum distance is up to approximately
system with any metal object, otherwise a short
150 feet (46 m) without the system picking up
circuit may occur.
some interference. However, the distance may
• If the contact points or the contact pins are dirty,
vary according to the surroundings and
charging may not occur. Clean them regularly
environment. If the system picks up some noise
with a soft cloth, etc., taking care not to damage
while using it within the above mentioned
the contact pins.
distance, reduce the distance between the
Note on cleaning
transmitter unit and the speaker system, or select
Clean the cabinet of the speaker system with a soft
another channel.
cloth slightly moistened with water or a mild
Notes
detergent solution. Do not use any type of abrasive
• When you use the speaker system within the effective
pad, scouring powder or solvent such as alcohol or
areas of the transmitter, the transmitter can be placed in
benzene as it may mar the finish of the cabinet.
any direction from the listener.
• Even within the signal reception area, there are some
When the color of your monitor screen
spots (dead spot) where the RF signal cannot be
becomes irregular
received. This is a characteristic inherent to RF signals,
and does not indicate malfunction. By slightly moving Because this speaker system is magnetically
the transmitter, location of the dead spot can be shielded, you can set it up near a monitor. But
changed.
depending on the model of the monitor, color
irregularity may occur.
Disposing of the To correct the color irregular
Turn off the monitor, and then turn it on again
speaker system
after 15 to 30 minutes.
Be sure to remove the built-in rechargeable battery
If color irregularity remains after
from the speaker system before you dispose of the
performing the above
speaker system.
• Separate the monitor and the speaker system.
1
• Make sure that no magnetic object, such as may
Remove 8 screws from the speaker
be attached to a door of shelf, healthcare device
system using a cross-point screw driver
or toys, etc., is located near the speaker system.
as illustrated below.
If you have any questions or problems concerning
the system that are not covered in this manual,
please consult your nearest Sony dealer.
Be sure to bring the speaker system and the
transmitter to the Sony dealer when requiring
repair work.
Troubleshooting
No sound/Muffled sound
, Check the connection of the audio/video
equipment.
, Check that the audio/video equipment is turned
on.
, Turn up the volume on the connected audio/
video equipment, if the transmitter is connected
to the headphones jack.
, Change the radio frequency with the CHANNEL Supplied accessories
selector on the transmitter, then adjust the TUNE AC adaptor (1)
dial again. Operating instructions (1)
, No sound is heard by wireless transmission.
Optional accessories
• If a cord is connected to the AUDIO IN jack of
Connecting cord RK-G129 (Stereo mini plug y
the speaker system, no sound is heard by
Phono plug × 2, 1.5 m)
wireless transmission. Disconnect the cord from
RK-G136 (Stereo mini plug y
the AUDIO IN jack first, and use the TUNE dial
Stereo mini plug, 1.5 m)
to adjust the tuning of the speaker system until
Plug adaptor PC-236MS (stereo mini jack y
sound is heard.
monaural mini plug)
, The speaker system's POWER indicator light is
Design and specifications are subject to change without notice.
turned off.
• Turn on the POWER switch, and turn it off, then
turn it on again.
Français
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
built-in rechargeable battery, take the speaker
AVERTISSEMENT
system to a Sony dealer for replacement of the
rechargeable battery.
Pour éviter tout risque d'incendie ou de choc
, If you connect the transmitter to the LINE OUT or
électrique, n'exposez pas l'appareil à la pluie ou
REC OUT jack of an audio reproducer, make sure
à l'humidité.
that the NOISE FILTER switch is set to OFF.
Pour prévenir tout risque d'électrocution,
, Make sure that the NOISE FILTER switch is set to
n'ouvrez jamais le coffret. Adressez-vous à un
either ON or OFF. (If the switch gets stuck
personnel qualifié uniquement pour toute
between ON and OFF, the sound will be cut off.) intervention sur l'appareil.
Avertissement
Distortion
Soyez avisé que toute modification non
, If the transmitter is connected to the headphones
expressément approuvée dans le présent mode
jack, turn down the volume of the connected
d'emploi pourrait entraîner l'annulation de vos
audio/video equipment. If the connected audio/
droits d'utilisation de ce produit.
video equipment has BASS BOOST function, set
its function to OFF. Pour les utilisateurs au Canada
, If the connected audio/video equipment has a Son utilisation est autorisée seulement aux
LINE OUT jack, connect its LINE OUT jack.
conditions suivantes: (1) il ne doit pas produire de
, Change the radio frequency with the CHANNEL
brouillage et (2) l'utilisateur du dispositif doit être
selector on the transmitter, then adjust the TUNE
prêt à accepter tout brouillage radioeléctrique reçu,
dial again.
même si ce brouillage est susceptible de
, The speaker system's POWER indicator light is
compromettre le fonctionnement du dispositif.
turned off.
• Turn on the POWER switch, and turn it off, then
Pour les utilisateurs aux Etats-Unis et au
turn it on again.
Canada
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
RECYCLAGE DES ACCUMULATEURS À
built-in rechargeable battery, take the speaker
HYDRURE MÉTALLIQUE DE NICKEL
system to a Sony dealer for replacement of the
rechargeable battery.
Les accumulateurs à hydrure
, If you connect the transmitter to LINE OUT or
métallique de nickel sont
REC OUT jack of an audio reproducer, make sure
recyclables.
that the NOISE FILTER switch is set to OFF.
Vous pouvez contribuer à
préserver l'environnement en
Loud background noise
rapportant les piles usées dans
, Move closer to the transmitter. As you move
un point de collection et
away from the transmitter, more noise is likely to
recyclage le plus proche.
be heard.
, If the transmitter is connected to the headphones
Pour plus d'informations sur le recyclage des
jack, turn up the volume of the connected audio/
accumulateurs, téléphonez le numéro gratuit
video equipment.
1-800-822-8837 (Etats-Unis et Canada
, Change the radio frequency with the CHANNEL
uniquement), ou visitez
selector on the transmitter, then adjust the TUNE
http://www.rbrc.org/
dial again.
, The speaker system's POWER indicator light is
Avertissment : Ne pas utilliser des
turned off.
accumulateurs à hydrure métallique de nickel
• Turn on the POWER switch, and turn it off, then
qui sont endommagées ou qui fuient.
turn it on again.
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
Bienvenue !
built-in rechargeable battery, take the speaker
system to a Sony dealer for replacement of the
rechargeable battery. Nous vous remercions d'avoir fait l'acquisition du
, If you connect the transmitter to the LINE OUT or système d'enceinte stéréo sans fil SRS-RF930RK de
REC OUT jack of an audio reproducer, make sure
Sony. Avant de faire fonctionner cet appareil, lisez
that the NOISE FILTER switch is set to OFF.
attentivement le présent mode d'emploi et
conservez-le pour toute référence ultérieure.
The CHARGE indicator does not light up
Cet appareil offre, entre autres, les caractéristiques
even though the speaker system sits on
suivantes :
the transmitter • Système sans fil permettant l'utilisation de votre
système sans être limité par le cordon des
, Remove the speaker system from the transmitter,
enceintes.
then replace it after 15 seconds.
• Longue portée de réception des signaux allant
, The speaker system is not placed correctly on the
jusqu'à environ 46 m (150 pi.).
transmitter.
• Ce système d'enceinte peut être alimenté par
, Place the speaker system in the correct orientation
onto the transmitter. une batterie rechargeable intégrée afin d'obtenir
, The speaker system is placed backwards on the un système d'enceinte sans fil parfait.
transmitter.
• Système intelligent de recharge de la batterie sur
, Clean the contact pins of the speaker system and
le transmetteur.
the contact points of the transmitter with a soft
• Enceinte de type stéréo à boîtier unique facile à
cloth.
transporter et permettant une installation dans
n'importe quel endroit.
The battery duration time is short
• 2 entrées sur le transmetteur permettent de
raccorder un ordinateur, ainsi que d'autres
, If you use the battery under the temperature
lower than 0 ˚C (32 ˚F), this is not a malfunction. équipements audio.
, The battery life may end. If the battery duration • 1 entrée analogique sur l'appareil principal
time becomes half of its normal time even after
permet de raccorder directement un autre
the battery is charged fully, consult your nearest
équipement audio portatif.
Sony dealer.
• Fonction de syntonisation manuelle disponible
sur l'enceinte.
Specifications
Remarques sur la
General
qualité de
Carrier frequency 913.5, 914, 914.5 MHz
Channel Ch1, Ch2, Ch3
transmission
Modulation FM stereo
Transmitter
Comme le système de cet appareil utilise des
Power source DC 9 V: supplied AC power adaptor
signaux de très haute fréquence dans la bande des
(AC-S901)
900 MHz, l'environnement de l'appareil peut
Audio input Input cord - stereo mini plug
entraîner une détérioration de la qualité de
(1.5 m)/stereo mini jack
transmission. Les exemples suivants illustrent les
Input impedance 27 kΩ /50 Ω at 1 kHz
situations pouvant réduire la plage de
Approx. 120 × 107 × 123 mm
Dimensions
transmission et perturber la réception.
× 4 × 4
(4 3 / 1 / 7 / in.) (w/h/d)
4 4 8 • Utilisation à l'intérieur d'un bâtiment à structure
Mass Approx. 192 g (6.8 oz.)
en acier.
Speaker system • Utilisation dans des pièces contenant de
Speaker system Full range, Bass reflex, magnetically nombreux classeurs ou autres éléments en acier.
shielded • Utilisation à proximité d'un grand nombre
Speaker Unit 57 mm (diameter) d'appareils électriques générant des parasites
Rated output 2 W électromagnétiques.
Audio input stereo mini jack • Installation du transmetteur sur un instrument
Input impedance 5.9 kΩ at 1 kHz métallique.
Dimensions Approx. 366 × 120 × 86 mm
• Utilisation à proximité d'une route.
( 14 1 / × 4 3 / × 3 1 / in.) (w/h/d)
• Parasites ou interférences autour de l'appareil,
2 4 2
Mass Approx. 905 g (31.9 oz.) incl.
provenant d'émetteurs-récepteurs de camions
built-in rechargeable battery
ou d'autres appareils.
• Parasites ou interférences autour de l'appareil,
Built-in Ni-MH rechargeable battery
provenant de systèmes de communication sans
Voltage 4.8 V
fil installés le long des routes.
Capacity 700 mAh
Duration time Approx. 14 hours* • Installation du transmetteur directement sur le
Charging time Approx. 16 hours (from fully sol. Il est recommandé d'installer le
discharged to fully charged) transmetteur en hauteur, par exemple sur un
* at 5 mW + 5 mW output bureau.
Raccordement du transmetteur à une
N Préparatifs
prise de courant à l'aide de
l'adaptateur CA fourni.
Déballage
Vérifiez que vous disposez de tous les éléments
Transmetteur
suivants :
• Système d'enceinte
Vers la
• Transmetteur prise
• Adaptateur CA DC IN 9 V
Vers une
prise de
courant
Raccordement du Adaptateur CA
(fourni : AC-S901 )
système
Remarque
Utilisez uniquement l'adaptateur CA fourni. N'utilisez
Raccordement du transmetteur à un aucun autre adaptateur CA afin de ne pas endommager le
transmetteur.
appareil audio ou vidéo
Installez le transmetteur en effectuant les étapes
suivantes. Choisissez le raccordement à effectuer
selon le type de prise de l'appareil audio ou vidéo
Polarité de la fiche
auquel vous souhaitez raccorder le transmetteur.
A Raccordement à une prise LINE OUT,
Recharge de la batterie
REC OUT ou une prise de casque.
du système d'enceinte
Transmetteur
Placez le système d'enceinte sur le transmetteur de
sorte que les broches de contact du système
d'enceinte touchent les points de contact du
transmetteur tout en vous assurant que le témoin
CHARGE s'allume en vert.
Système d'enceinte
OFF ON B A DC IN 9V 1 2 3
NOISE FILTER AUDIO IN CHANNEL
Vers la prise
AUDIO IN A
AUDIO IN B
POWER CHARGE
Vers une
Cordon de Cordon audio
prise de Transmetteur
raccordement (AUDIO IN A)
courant
(non fourni) Vers la prise
de casque ou
LINE OUT
(mini-prise
Canal gauche Canal droit
stéréo)
(blanc) (rouge)
POWER CHARGE
Vers une
Vers les prises
LINE OUT ou prise de
REC OUT courant
Broche de
contact
Point de
Ordinateur, etc. contact
Remarques
B Raccordement à un téléviseur ou à un
• Lors de la mise en charge de la batterie, mettez le
autre appareil.
système d'enceinte hors tension.
Si des parasites sont audibles lorsque le
• Le chargement complet s'effectue en 16 heures environ
transmetteur est relié à la prise de casque
et le témoin CHARGE s'éteint.
de votre téléviseur ou magnétoscope, • Rechargez la batterie rechargeable à une température
supérieure à 0 ˚C et inférieure à 35 ˚C (32 ˚F à 95 ˚F).
réglez le commutateur NOISE FILTER à
• Ne mettez le système d'enceinte sous tension lors de la
ON.
mise en charge de la batterie. Sinon, la batterie risque de
ne pas être entièrement rechargée.
• Ne retirez pas le système d'enceinte du transmetteur
Transmetteur
avant que la recharge ne soit terminée.
• Si vous retirez le système d'enceinte du transmetteur,
puis que vous le remettez en place, la recharge sera plus
longue.
• Si vous retirez accidentellement le système d'enceinte
du transmetteur, puis que vous le remettez en place
dans les 5 secondes, le temps de charge ne sera pas
OFF ON DC IN 9V 1 2 3
B A affecté.
NOISE FILTER AUDIO IN CHANNEL
• Si vous chargez de nouveau le système d'enceinte après
l'extinction du témoin CHARGE, retirez-le du
AUDIO IN A transmetteur, puis remettez-le en place après environ
15 secondes.
• Pour prolonger la durée de vie de la batterie
rechargeable, chargez-la uniquement lorsqu'elle est
complètement vide.
Cordon audio
• La durée de vie de la batterie rechargeable intégrée est
(AUDIO IN A)
d'environ trois ans, mais elle peut être plus ou moins
longue selon les conditions d'utilisation.
N Utilisation du système
Vers la prise de
casque ou LINE OUT
(mini-prise stéréo) Écoute d'un programme
Avant d'utiliser le système d'enceinte, rechargez la
batterie rechargeable intégrée.
Téléviseur ou Baissez le volume du système d'enceinte avant de
autre appareil commencer à écouter un programme à partir de
l'appareil audio ou vidéo raccordé.
Remarques
Écoute d'un programme à partir du
• Si vous raccordez le transmetteur à une prise LINE OUT
transmetteur, par l'entremise d'une
ou REC OUT, ne réglez pas le commutateur NOISE
FILTER à ON, sinon le volume sera limité. transmission sans fil
• Le commutateur NOISE FILTER est uniquement activé
lors d'une connexion avec AUDIO IN A.
• Placé près d'un téléviseur, le transmetteur risque de
Molette TUNE
subir des interférences. Le cas échéant, éloignez-le du
téléviseur.
• Lorsque vous raccordez directement le cordon de
raccordement à une prise de casque, le signal audio n'est
pas émis par le canal droit. Dans ce cas, utilisez
l'adaptateur de fiche PC-236MS vendu séparément.
• Si l'appareil raccordé est équipé de la fonction AVLS
Commutateur AUDIO IN
(système de limitation automatique du volume),
POWER
désactivez cette fonction lorsque vous utilisez le
Commande
Témoin POWER
transmetteur. Sinon, vous devrez augmenter le volume
VOLUME
du système d'enceinte, ce qui pourrait engendrer des
1
Mettez d'abord l'équipement audio et
parasites.
• Si l'appareil raccordé est équipé de la fonction BASS vidéo sous tension et démarrez la
BOOST ou MEGA BASS désactivez cette fonction
lecture.
lorsque vous utilisez le transmetteur. Sinon, le son
Le témoin POWER du transmetteur
provenant du système d'enceinte risque d'être déformé.
s'allume.
• N'installez pas le transmetteur près d'une lampe
fluorescente, etc. lorsque vous utilisez le système. 2
Mettez le système d'enceinte sous
tension.
Le témoin POWER du système
d'enceinte s'allume en rouge.
Voir page suivante