Siemens Climatix Series Basis Document page 196

Main Index > Unit > Fan Control > Supply Fan > Setpoints/Settings
Parameter Function
Stage 2 Output for Stage 2 if Fan control mode is
FixedSpeed, Pressure, Flow or ExhaustSlv
Stage 3 Output for Stage 3 if Fan control mode is
FixedSpeed, Pressure, Flow or ExhaustSlv
Max forcing Maximum allowed Setpoint for
compensations
Min run time Min Run Time
Switch on delay Switch On delay time
Start up delay fdbk Supply Fan Feedback Start up Delay
Deviation alarm Actual Status; Jumpline for Settings
Main Index > Unit > Fan Control > Supply Fan > Setpoints/Settings > Deviation alarm
Parameter Function
Alarm Actual Status Supply Deviation alarm
Min limit Lowest allowed Present Value for alarm
Maximum deviation In maximum allowed Deviation
Start up delay Delay until the Deviation is supervised
Main Index > Unit > Fan Control > Exhaust fan
Parameter Function
Actual value Exhaust fan Actual Value
Controller Actual Value Controller; Jumpline to settings 0...100
Output signal Actual Output Signal; Jumpline to settings
Command Actual Stage; Jumpline to settings
Feedback Feed back of Supply Fan
Alarm Exhaust fan alarm
Alarm Fan alarm if combined Fan
Setpoints/Settings Actual Value; Jumpline to Exhaust fan
Setpoints and settings
Main Index > Unit > Fan Control > Exhaust fan > Setpoints/Settings
Parameter Function
Actual step Exhaust fan Actual Stage
Act supply stpt Actual Setpoint
Stage 1 Output for Stage 1 if Fan control mode is
FixedSpeed, if Fan control mode is Pressure,
Flow or SupplySlv Setpoint Stage 1
Stage 2 Output for Stage 2 if Fan control mode is
FixedSpeed, if Fan control mode is Pressure,
Flow or SupplySlv Setpoint Stage 2
Stage 3 Output for Stage 3 if Fan control mode is
FixedSpeed, if Fan control mode is
Pressure, Flow or SupplySlv Setpoint Stage
3
Max forcing Maximum allowed Setpoint for
compensations
Min run time Min Run Time
Start up delay fdbk Actual Status; Jumpline for Settings
Deviation alarm Actual Status; Jumpline for Settings
196 / 244
Basis Document Siemens Climatix Control System
Siemens
Page 196
BDCX.100820.01GB
Building Technologies
17.14.4 Supply fan deviation alarm
17.14.5 Exhaust fan
17.14.6 Exhaust fan settings
Standard application AHU
HMI
Value range Unit
0...100 %
l/s
Pa
0...100 %
l/s
Pa
0...19900 %
l/s
Pa
0...36000 --- S ---
0...36000 --- S ---
0...36000 --- S ---
Passive
Active
Value range Unit
Active...passive
-64...64 °C
-64...64 °C
0...36000 --- S ---
Value range Unit
0...100 %
%
0...100 %
Off...St3
Nofdbk...fdbk
OK...alarm
OK...alarm
Value range Unit
Off...St3
0...100 %
0...100 %
l/s
Pa
0...100 %
l/s
Pa
0...100 %
l/s
Pa
0...19900 %
l/s
Pa
0...36000 --- S ---
Passive
Active
Passive
Active
Standard R S Link
80% 6
100% 6 Section:
5.4.3
0% 6
0 6
30 6
60 6
x
Standard R S Link
X
10 6 Section:
10 6
5.4.5
60 6
Standard R S Link
X
X
X
X Section:
6
5.4.3
6
6
6
Standard R S Link
X
X
40% 6
80% 6
Section:
5.4.3
100% 6
0% 6
0 6
x
x
CE1P3977en_02
01.02.2010