Contents Before Use ...6 Notice ...7 Documentation ...8 Ergonomic Considerations ...11 Getting Started ...13 Locating Controls and Ports...14 About the Indicator Lights ...19 Setting Up Your Computer ...20 Shutting Down Your Computer Safely ...36 Using Your VAIO Computer ...37 Using the Keyboard ...38 Using the Touch Pad ...42 Using the Mouse ...43 Using the Built-in MOTION EYE Camera...46...
Page 3
Using the Network (LAN) ...102 Using the Wireless LAN (WLAN) ...104 Using the Bluetooth Function ...107 Using Peripheral Devices...112 Connecting External Speakers ...113 Connecting a Universal Serial Bus (USB) Device...115 Connecting a Printer ...117 Connecting an i.LINK Device ...118 Customizing Your VAIO Computer ...120 Setting the Password ...121 Setting Up Your Computer with the VAIO Control Center...126 Using the Power Saving Mode...127...
Page 4
Precautions ...144 Handling the LCD Screen ...145 Using the Power Source ...146 Handling Your Computer ...147 Handling the Built-in MOTION EYE Camera...150 Handling Floppy Disks ...151 Handling Discs ...152 Using Headphones ...155 Handling the Memory Stick ...156 Handling the Hard Disk ...157 Updating Your Computer ...158 Troubleshooting ...159 Computer ...161...
Page 5
Keyboard...189 Floppy Disks ...191 Audio/Video...192 HDMI Input ...196 Memory Stick ...198 Peripherals ...199 Support Options ...200 Sony Support Information ...200 Trademarks ...204...
Information in the supplied manuals including this User Guide is intended for users of the VAIO computers with the Microsoft 32-bit operating system. You may find differences in the information when your computer comes preinstalled with the 64-bit operating system. ® computer, and welcome to the on-screen User Guide. Sony has Before Use ®...
In the manual, the ™ or ® marks are not specified. Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein is governed by the terms of a separate user license agreement.
❑ Specifications — The online specifications describe the hardware and software configurations of your VAIO computer. To view the online specifications: Connect to the Internet. Go to the Sony online support web site at the following URLs: http://esupport.sony.com/EN/VAIO/ http://www.sony.ca/support/ http://esupport.sony.com/LA/ http://esupport.sony.com/BR/...
Page 9
❑ VAIO Recovery Center User Guide — Provides information about restoring individual software programs, hardware drivers, and drive partition(s) or your entire hard disk drive to the original factory settings. To access this on-screen guide: Click Start and Help and Support. Click Use my VAIO.
Access your VAIO user guide, interactive help in the form of VAIO tutorials, how-to articles, the VAIO technology page, specifications, and system and software information. ❑ Troubleshoot my VAIO Maintain and troubleshoot your VAIO computer with VAIO Care, system restore, backup and recovery, and contact Sony support. Before Use...
Ergonomic Considerations Whenever possible, you should attempt to take account of the following ergonomic considerations: ❑ Position of your computer – Place the display directly in front of you (1). Keep your forearms horizontal (2), with your wrists in a neutral, comfortable position (3) while using the keyboard, pointing device, or mouse. Let your upper arms hang naturally at your sides.
Page 12
❑ Viewing angle of the display – Use the display's tilting feature to find the best position. You can reduce eye strain and muscle fatigue by adjusting the tilt of the display to the proper position. Adjust the brightness level of the display as well. While adjusting the viewing angle, do not exert excessive pressure on your computer, especially on the center of the speaker grill, to eliminate a risk of mechanical damage.
Getting Started This section describes how to get started using your VAIO computer. Before starting your computer for the first time, do not connect any other hardware that did not originally come with your computer. Be sure to start up your computer with only the supplied accessories connected and set up your system. Upon completion, connect one device (for example, a printer, an external hard disk drive, a scanner, and so on) at a time, following the manufacturers' instructions.
Built-in MOTION EYE camera (page 46) Power indicator (page 19) Remote sensor Point the supplied remote commander to this sensor for operations. SONY logo lamp (page 126) LCD screen (page 145) HDMI SELECT indicator (page 19) WIRELESS indicator (page 19)
Page 15
Back Power button DISPLAY OFF button Press this button to turn off the LCD backlight. While the HDMI input is selected (page 80), pressing this button also turns off the volume. Capture angle adjuster (page 46) Back panel cover Remove the back panel cover to access the ports and jacks behind it (page 20).
Page 16
The area around the air exhaust vent (1) becomes hot while your computer is on. Be sure to wait until the computer cools down before you touch it. Air exhaust vent (page 148) HARD DISK DRIVE ACCESS BAY cover Memory module compartment cover (page 133) AC In port (page 25)
Page 17
Right Optical disc drive (page 50) Drive eject button (page 51) Hi-Speed USB (USB 2.0) ports (page 115) WIRELESS switch (page 104) HDMI SELECT button (page 80) MENU button (page 80) Up/Down buttons (page 80) OK button (page 80) Support high-/full-/low- speeds. Getting Started...
Page 18
Left ExpressCard/34 slot (page 88) Memory Stick slot (page 92) Media Access indicator (page 19) SD memory card slot (page 98) Headphones jack (page 113) Microphone jack Connect an external microphone. Line In jack Connect an external audio device for audio input. Hi-Speed USB (USB 2.0) port (page 115) Your computer supports both the standard-size Memory Stick and the Duo-...
About the Indicator Lights Your computer is equipped with the following indicator lights: Indicator Functions Power 1 Illuminates in green when the computer is on, illuminates in orange while the computer is in Sleep mode, and turns off when the computer is off. Built-in MOTION EYE camera Illuminates while the built-in MOTION EYE camera is in use.
Setting Up Your Computer Removing and Replacing the Covers Before accessing some ports and jacks on the back of your computer, you first need to remove the back panel cover from the computer and the base stand cover from the base stand. To remove the back panel cover and the base stand cover Gently face down your computer on a flat surface.
Page 21
Getting Started Grasp the back panel cover (1) with both hands, gently lift it, and remove it from the computer. Put your fingertips underneath the back panel cover (2) when removing the cover from the computer.
Page 22
Getting Started Slide the base stand cover (3) in the direction of the arrow and remove it from the base stand.
Page 23
Getting Started To replace the back panel cover and the base stand cover Put the base stand cover (1) back on the base stand and slide it in the direction of the arrow.
Page 24
Getting Started Put the back panel cover (2) so as to fit the projections inside the cover into the respective holes on the back of the computer and push in the cover toward the computer. Keep the back panel cover and the stand cover on the computer unless access to the back panel is necessary.
Page 25
Connecting a Power Source and Cables You need a power cord to connect your computer to an AC power source and it must be plugged into the power source before you establish communication with your wireless keyboard and mouse. In addition, you need to connect other cables if you want to use some functions of your computer, such as the TV function.
Page 26
To connect the power cord and other cables Remove the back panel cover and the base stand cover from the computer. See Removing and Replacing the Covers Plug one end of the power cord (1) into the AC outlet (2), put the other end through the hole (3) in the base stand, and plug it into the AC In port (4) on the computer as illustrated below.
Page 27
Connect other cables to the computer, if necessary. ❑ To set up TV connections, see Using the TV Function ❑ To connect an HDMI cable to the HDMI INPUT port for using the HDMI Input function, see Using the HDMI Input Function (page 79).
Page 28
Getting Started Replace the stand cover and the back panel cover. See Removing and Replacing the Covers (page 20) for the procedure. ✍ To disconnect your computer completely from AC power, unplug the power cord when the computer is off. Make sure that the AC outlets are easily accessible.
Connecting the Wireless Keyboard A wireless keyboard and four AA alkaline batteries for use in the keyboard are supplied with your computer. Before attempting to use the wireless keyboard, you must install the batteries and establish communication between the computer and the keyboard.
Page 30
Getting Started ✍ You can check the battery indicator ( ) in the LCD window on the wireless keyboard for its battery power level. If the wireless keyboard does not operate properly, the batteries may need to be replaced. If you do not intend to use the wireless keyboard for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
Connecting the Wireless Mouse A wireless mouse and two AA alkaline batteries for use in the mouse are supplied with your computer. Before attempting to use the wireless mouse, you must install the batteries and establish communication between your computer and the mouse. ✍...
Page 32
Slide the power switch on the bottom of the mouse to the ON position. Press the CONNECT button (1) on the back of the computer. Press the CONNECT button on the bottom of the mouse within 10 seconds from step 4. Communication between the mouse and the computer should now be established.
Preparing for Wall Mounting Your computer is equipped with four holes on its back panel, which look similar to those compliant with the Video Electronics Standards Association (VESA) mounting standard, for connecting to your mounting system. Be sure to establish wireless communication between your computer and the wireless mouse and keyboard before mounting the computer on the wall. It is recommended that you allow adequate clearance between the wall and the back of your computer when mounting the computer on the wall so that you can access the ports and buttons on the back of the computer.
Page 34
To reveal the mounting holes Remove the back panel cover from the computer. See Removing and Replacing the Covers Unscrew the six screws (1) and remove the base stand (2). (page 20) for the procedure. Getting Started...
Page 35
Getting Started Use the four holes (3) for mounting by following the instructions described in the manual that came with your mounting system.
Shutting Down Your Computer Safely To avoid losing unsaved data, be sure to shut down your computer properly, as described below. To shut down your computer Turn off any peripherals connected to the computer. Click Start, the arrow next to the Lock button, and then Shut Down. Respond to any prompts warning you to save documents or to consider other users and wait for the computer to turn off automatically.
Using Your VAIO Computer Using Your VAIO Computer This section describes how to get the most out of using your VAIO computer. ❑ Using the Keyboard (page 38) ❑ Using the Touch Pad (page 42) ❑ Using the Mouse (page 43) ❑...
Using the Keyboard A wireless keyboard is supplied with your computer. The wireless keyboard uses a standard key arrangement with additional keys that perform specific functions. Using the Wireless Keyboard To maintain good communication, operate the wireless keyboard within the distance limitations of keyboard: approximately 32.8 feet (10 m) from your computer.
Page 39
✍ Illustrated above is the English keyboard as an example. Using Your VAIO Computer Zoom buttons Changes the size of an image or a document displayed on some software. Press to make the view look smaller and further away (zoom out).
Page 40
Indicators (Battery): turns on while the AA batteries for the wireless keyboard are sufficient and switches to batteries wear out. (Num lock): Turns on while in the Num Lock state. (Caps lock): Turns on while in the Caps Lock state. (Scroll lock): Turns on while in the Scroll Lock state.
Page 41
Using Your VAIO Computer Keyboard feet Flip open to adjust the keyboard angle. CONNECT button (page 29) Press to enable the wireless keyboard to communicate with the computer. Battery compartment Storage compartment for the AA batteries.
Using the Touch Pad You can point to, select, drag, and scroll objects on the screen using the touch pad. Action Description Point Slide your finger on the touch pad (1) to place the pointer (2) on an item or object. Click Press the left button (3) once.
Using the Mouse A wireless mouse is supplied with your computer. Using the Wireless Mouse The wireless optical mouse has no cables to plug in and uses a light-emitting diode (LED) instead of a ball. To maintain good communication, operate the wireless mouse within the distance limitations of mouse: approximately 32.8 feet (10 m) from your computer.
Page 44
Using Your VAIO Computer Left button Click or double-click the left button to select items. To drag and drop items, hold the left button down while sliding the mouse, then release the button to drop the item. Central wheel Rotate the central wheel to scroll up or down a page. Press the wheel once to lock the scroll action and control the movement by moving the entire mouse (the scroll function is available only with applications that support it).
Page 45
Adjusting the Mouse Functions Click Start and Control Panel. Click Mouse under Hardware and Sound. The Mouse Properties window appears. Change the settings. Using Your VAIO Computer...
Using the Built-in MOTION EYE Camera Your computer is equipped with a built-in MOTION EYE camera. The built-in MOTION EYE camera adds video functionality to instant messaging software and video editing software and enables you to capture still images and movies with the preinstalled image capture software. Turning on the computer activates the built-in MOTION EYE camera.
Page 47
Using Your VAIO Computer The viewer window may show some noise, for example horizontal streaks, if you view a rapid-moving object. This is normal and does not indicate a malfunction. You cannot operate the built-in MOTION EYE camera with the Microsoft Windows Movie Maker software.
Capturing Still Images To capture a still image Click Start, All Programs, ArcSoft WebCam Companion 2, and WebCam Companion 2 to launch the WebCam Companion 2. Click the Capture icon in the main window. Frame your subject in the viewfinder. Click the Capture button below the displayed image.
Capturing Movies To capture a movie Click Start, All Programs, ArcSoft WebCam Companion 2, and WebCam Companion 2 to launch the WebCam Companion 2. Click the Record icon in the main window. Frame your subject in the viewfinder. Click the Record Video button below the displayed image to start movie recording. When finished, click the Record Video button once again to stop movie recording.
Using the Optical Disc Drive Your computer is equipped with an optical disc drive. To insert a disc Be sure to attach the 8 cm disc adapter to an 8 cm disc before inserting the disc into the optical disc drive slot. Slide the disc straight into the slot so as not to apply excessive pressure to the disc or slot.
To remove a disc The drive eject button is disabled when your computer is turned off. Do not remove the optical disc when your computer is in Sleep mode. Doing so may cause the computer to malfunction. Be sure not to pull out the optical disc forcefully before it completely slides out. Check that the Hard disk drive/Optical disc drive indicator light (1) is unlit.
Page 52
Using Your VAIO Computer Reading and Writing Optical Discs ™ Your computer plays and records CDs, DVDs, and Blu-ray Disc media, depending on the model you purchased. Check your specifications for the type of optical disc drive installed on your model. Use the table below to see which types of media your optical disc drive supports.
Page 53
Video Music Extra DVD±RW/ ±R DL/RAM Blu-ray Disc Combo Blu-ray Disc P Supports writing data to DVD-R discs compliant with DVD-R for General Version 2.0/2.1. Supports writing data to DVD-RW discs compliant with DVD-RW Version 1.1/1.2. The DVD±RW/RAM disc drive on your computer does not support the DVD-RAM cartridge. Use non-cartridge discs or discs with a removable cartridge. Writing data to single-sided DVD-RAM discs (2.6 GB) compliant with DVD-RAM Version 1.0 is not supported.
Page 54
When you buy pre-recorded or blank discs for use with your VAIO computer, be sure to read the notices on the disc package carefully to check both playback and recording compatibility with your computer's optical disc drives. Sony does NOT guarantee the compatibility of VAIO optical disc drives with discs that are not compliant with the official "CD,"...
Page 55
Using Your VAIO Computer Notes on writing data to a disc ❑ Only use circular discs. Do not use discs in any other shape (star, heart, card, etc.), as this may damage the optical disc drive. ❑ Do not strike or shake your computer while the optical disc drive is writing data to a disc. ❑...
Page 56
Notes on playing discs To achieve optimum performance when playing discs, you should follow these recommendations. ❑ Some CD players and computer optical disc drives may not be able to play audio CDs created with the CD-R or CD-RW media. ❑...
Playing CDs To play an audio CD Insert a disc into the optical disc drive. If nothing appears on the desktop, click Start, All Programs, and the desired CD software to play the CD. If the Audio CD window appears, click to select an option. Copying Files to CDs To copy files to a disc Insert a recordable disc into the optical disc drive.
Playing DVDs To play a DVD Close all running software applications. Insert a DVD into the optical disc drive. If nothing appears on the desktop, click Start, All Programs, and the desired DVD software to play the DVD. For instructions on how to use the software, see the help file included with your DVD software. Copying Files to DVDs To copy files to a disc Close all running software applications.
Playing Blu-ray Disc Media To play a Blu-ray Disc media Close all running software applications. Insert a Blu-ray Disc media into the optical disc drive. If nothing appears on the desktop, click Start, All Programs, and the desired Blu-ray Disc software to play the disc. For instructions on how to use the software, see the help file included with your software.
Using Your VAIO Computer Using the TV Function To enhance your audio and visual experience in conjunction with the Windows Media Center, your computer may have one or two TV tuner boards installed: one analog tuner board and one ATSC tuner board, or one analog tuner board only. See the online specifications to find out about your TV tuner board configuration.
Setting Up TV Connections The following connections may not be available in some countries or areas. The best method to connect your computer system, TV monitor or display, and cable service access, depends on the type of cable connection available in your home. TV signal reception strength will vary widely depending on service availability in your area as well as the type of connection available.
Connecting to standard cable access (CATV) The appearance of your computer and the location of the ports may be different from those illustrated in this manual due to variations in specifications. It may also vary in some countries or areas. To connect in CATV mode (Option 1) Connect one end of the TV coaxial cable (1) (supplied) to your cable service access (wall outlet) (2).
Page 63
To connect in CATV mode (Option 2) Connect the two metal hooks on a 75-ohm/300-ohm RCA transformer cable (1) (not supplied) to the screw-type grips at your cable service access (wall outlet) (2). Connect one end of the TV coaxial cable (3) (supplied) to the transformer end of the RCA transformer cable (1). Connect the other end to the CABLE/ANT ANALOG input port (4) on the computer.
Connecting to a standard antenna You can connect your computer to an indoor/outdoor antenna system, using Option 1 or Option 2 from the previous section, Connecting to standard cable access (CATV) connection may require a VHF/UHF RF combiner/transformer (not supplied) to connect the computer and the indoor/outdoor antenna system.
Page 65
To connect in land-based (terrestrial) broadcasting mode (Option 1) Connect one end of a TV coaxial cable (1) (supplied) to your antenna outlet (2). Connect the other end to a VHF/UHF RF combiner/transformer (3) (not supplied). Connect a coaxial cable feed connector (4) (not supplied) to the VHF/UHF RF combiner/transformer (3). Connect one end of another TV coaxial cable (5) (not supplied) to the feed connector (4).
Page 66
To connect in land-based (terrestrial) broadcasting mode (Option 2) Connect one end of a 300-ohm twin lead cable (1) (not supplied) to the screw-type grips at your antenna outlet (2). Connect the other end to the grips on a VHF/UHF RF combiner/transformer (3) (not supplied). Connect a coaxial cable feed connector (4) (not supplied) to the VHF/UHF RF combiner/transformer (3).
Page 67
To connect to an antenna (air) for digital television system (ATSC signal standard) If you have an antenna for receiving the over-the-air signals transmitted by a digital TV broadcasting system, you can connect it to receive these signals for digital televisions, for example high definition TVs. Connect one end of the TV coaxial cable (1) (supplied) to an ATSC antenna (not supplied) (2).
Connecting with a cable or satellite set-top box (STB) You can connect your computer to cable service access that uses a set-top box (cable or satellite). When using the set-top box (STB) setup, you can change channels only through the STB, using its controls or the supplied remote commander. When using the STB setup: ❑...
Page 70
To connect in STB mode (Option 2) Connect one end of a TV coaxial cable (1) (not supplied) to your cable service access (wall outlet) (2). Connect the other end to the VHF/UHF input port on the back panel of your set-top box (STB) (3). Connect a second TV coaxial cable (4) (not supplied) to the VHF/UHF output port on the set-top box (STB) (3).
Using Your VAIO Computer Using the Remote Commander A remote commander is supplied with your computer for using a wide variety of AV related software applications, including the Windows Media Center.
Page 73
✍ Illustrated above is the English remote commander as an example. Using Your VAIO Computer Pause X button Press to pause media playback. Press again to resume playback. Stop x button Press to stop media playback or TV recording session. Forward M button Press to fast-forward media at three speeds.
Page 74
Guide button Press to view the TV program guide for your area. Alphanumeric buttons Press to select specific channels or enter text. (Press ENTER or OK to activate the channel selection.) CLEAR button Press to backspace and delete entered text. APPLICATION SELECT button Press to switch among open applications.
Page 75
Before you use the remote commander Before using the remote commander, you need to insert the supplied AA manganese batteries to enable communication between the computer and the remote commander. To insert batteries Turn the remote commander over. Slightly push down the dented area (1), slide the battery cover in the direction of the arrow, and remove the cover. Using Your VAIO Computer...
Page 76
Insert the supplied two AA batteries into the remote commander. Put the battery cover back on the remote commander and slide it in the reverse direction of the arrow illustrated above until the cover clicks into place. ✍ If the remote commander does not operate properly, you may need to replace the batteries. When the remote commander is not going to be used for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
Page 77
To connect the remote sensor control ✍ If you are using a cable or satellite set-top box, you can attach the remote sensor control to the set-top box, which enables you to control the set-top box with the remote commander. You need to remove the back panel cover from the computer before connecting the remote sensor control.
Page 78
Remove the adhesive tape cover from the bottom of the remote sensor control (1). Attach the remote sensor control (1) onto the set-top box (3) near the infrared sensor (4). Do not cover the infrared sensor when attaching the remote sensor control. The remote sensor must be visible in a line of sight with the remote commander in order to function properly.
Using the HDMI Input Function Your computer is equipped with an HDMI INPUT port that enables you to connect a device with the HDMI output port, such as a hard disk drive recorder and a video game player, to the computer. With the HDMI Input function, the computer can receive the high-definition video and sound outputs from the connected device and you can view and hear them on the computer without turning on your computer and starting Windows.
Page 80
Using the HDMI Input Control Buttons The HDMI input control buttons allow you to switch the display and sound input between the computer input and the HDMI input from the connected device and change the display and sound settings for the HDMI input. HDMI input control buttons HDMI SELECT button MENU button...
Page 81
Connecting and Using the HDMI-Compatible Device You need to connect the HDMI-compatible device to your computer with an HDMI cable to display the HDMI input from the device on the computer. Be sure to use an HDMI cable approved by HDMI Licensing, LLC. To connect your computer to the HDMI-compatible device ✍...
Page 82
To change the HDMI input volume Press the Up (V) or the Down (v) button to increase or decrease the volume. While the HDMI input is selected, you can only use the Up/Down buttons to change the volume. You cannot use the volume control buttons on the wireless keyboard or the supplied remote commander to change the volume.
Page 83
You can change the display and sound settings for the HDMI input with the OSD menu. The following shows how to change the language mode of the OSD menu, enable or disable the Auto Input Sensing feature, and change the default SONY logo lamp activity while the HDMI input is selected.
Page 84
To select the language mode of the OSD menu Press the MENU button to display the OSD menu. Press the Up (V) or Down (v) button to select OPTION and then the OK button. Press the Up (V) or Down (v) button to select LANGUAGE and then the OK button. Press the Up (V) or Down (v) button to select the desired language and then the OK button.
Page 85
To change the default SONY logo lamp activity You cannot change this option while the computer input is selected. To change the settings for the computer mode, see Changing the default SONY logo lamp activity (page 126) for the procedure.
Page 86
Viewing TV Programs with the HDMI Input Function If you are using a set-top box with an HDMI output port to view TV programs, you can display them on your computer with the HDMI Input function. You cannot record the HDMI input, such as a TV program, displayed on your computer or control the Windows Media Center with the HDMI Input function.
Page 87
To connect a set-top box using the HDMI INPUT port Connect one end of a TV coaxial cable (1) (supplied) to your cable service access (wall outlet) (2). Connect the other end to the VHF/UHF input port on the back panel of your set-top box (STB) (3). Connect a second TV coaxial cable (4) (not supplied) to the VHF/UHF output port on the set-top box (STB) (3).
Using the ExpressCard Module Your computer is equipped with an ExpressCard/34 slot players, and other audio/video devices. This slot can only accommodate an ExpressCard/34 (34 mm wide) module Referred to as the ExpressCard slot and the ExpressCard module in this manual. Inserting an ExpressCard Module Your computer is supplied with a slot protector in the ExpressCard slot.
Page 89
To insert an ExpressCard module Locate the ExpressCard slot (page Push the ExpressCard slot protector so that the protector pops out. Gently take hold of the ExpressCard slot protector and pull it out of the slot. Carefully slide the ExpressCard module into the slot until it clicks into place. Make sure that the arrow on the ExpressCard module is pointing toward the ExpressCard slot.
Page 90
Using Your VAIO Computer ✍ If the module does not go into the slot easily, remove it gently and verify you are inserting it in the proper direction. Make sure you use the most recent software driver provided by the ExpressCard module manufacturer.
Removing an ExpressCard Module Insert the ExpressCard slot protector to block any particles from entering the slot when not using an ExpressCard module. Before moving your computer, be sure to insert the ExpressCard slot protector into the slot. Follow the steps below to remove the ExpressCard module while your computer is on. If it is not removed properly, your system may not work properly.
Using Your VAIO Computer Using the Memory Stick The Memory Stick is a compact, portable, and versatile IC recording media especially designed for exchanging and sharing digital data with compatible products, such as digital cameras, mobile phones, and other devices. Because it is removable, it can be used for external data storage.
Page 93
For the latest information about the Memory Stick, visit the Memory Stick web site at http://www.memorystick.com/en/. Your computer has been tested and found compatible with Sony branded Memory Stick with capacity of up to 16 GB that are available as of September 2008.
Page 94
Inserting a Memory Stick To insert a Memory Stick Locate the Memory Stick slot (page Hold the Memory Stick with the arrow pointing toward the slot. Carefully slide the Memory Stick into the slot until it clicks into place. The Memory Stick is automatically detected by your system and the contents on the Memory Stick are displayed. If nothing appears on the desktop, click Start, Computer, and double-click the Memory Stick icon.
Page 95
Be sure to hold the Memory Stick with the arrow pointing in the correct direction as you insert it into the slot. To avoid damaging your computer or the media, do not force the Memory Stick into the slot if you cannot insert it smoothly. Do not insert more than one Memory Stick into the slot.
Page 96
To format a Memory Stick The Memory Stick has been formatted in the factory default setting and is ready for use. If you want to reformat the media with your computer, follow these steps. Be sure to use the device that is designed to format the media and supports the Memory Stick when formatting the media. Formatting the Memory Stick erases the entire data on the media.
Page 97
Removing a Memory Stick Do not remove the Memory Stick while the Media Access indicator light is lit. If you do, you may lose data. Large volumes of data may take time to load, so make sure the indicator is unlit before removing the Memory Stick. To remove a Memory Stick Check that the Media Access indicator light is unlit.
❑ SDHC memory card ❑ MultiMediaCard (MMC) For the latest information on compatible memory cards, see Sony Support Information support web site. Your computer has been tested and found compatible only with major memory cards available as of September 2008. However, not all memory cards that meet the same specifications as the compatible media are guaranteed of compatibility.
Inserting an SD Memory Card To insert an SD memory card Locate the SD memory card slot Hold the SD memory card with the arrow pointing toward the slot. Carefully slide the SD memory card into the slot until it clicks into place. Do not force the card into the slot.
Page 100
Removing an SD Memory Card Do not remove an SD memory card while the Media Access indicator light is lit. If you do, the card or its data may become damaged. To remove an SD memory card Check that the Media Access indicator light is unlit. Push in the SD memory card toward the computer and release.
Using the Internet Before using the Internet, you need to sign up with an Internet Service Provider (ISP) and set up devices required for connecting your computer to the Internet. The following types of Internet connection services may be available from your ISP: ❑...
Using the Network (LAN) You can connect your computer to 1000BASE-T/100BASE-TX/10BASE-T type networks with an Ethernet network cable. Connect one end of a network cable (not supplied) to the network (Ethernet) port on the back of the computer and the other end to your network.
Page 103
Using Your VAIO Computer Do not plug a telephone cable into the network (Ethernet) port on your computer. If the network (Ethernet) port is connected to one of the telephone lines mentioned below, high electric current to the port may cause damage, overheating, or fire.
Using the Wireless LAN (WLAN) Using the Wireless LAN (WLAN), all your digital devices with the built-in WLAN function communicate freely with each other through a network. A WLAN is a network in which a user can connect to a Local Area Network (LAN) through a wireless (radio) connection.
Page 105
Using Your VAIO Computer ✍ In some countries, using WLAN products may be restricted by the local regulations (e.g. limited number of channels). Therefore, before activating the WLAN function, read the Safety Information carefully. WLAN uses the IEEE 802.11a /b/g standard or the IEEE 802.11n draft standard, which specifies the used technology.
Page 106
Using Your VAIO Computer The communication speed varies depending on the distance between communication devices, existence of obstacles between such devices, the device configuration, the radio conditions, and the software in use. In addition, communications may be cut off depending on the radio conditions. The communication range varies depending on the actual distance between communication devices, existence of obstacles between such devices, the radio conditions, the ambient environment that includes existence of walls and materials of such walls, and the software in use.
Using Your VAIO Computer Using the Bluetooth Function ® You can establish wireless communications between your computer and other Bluetooth devices such as another computer or a mobile phone. You can transfer data between these devices without cables at a range of up to 33 feet (10 meters) in an open area.
Page 108
Notes on using the Bluetooth function ❑ The data transfer rate varies, depending on the following conditions: ❑ Obstacles, such as walls, located between devices ❑ Distance between devices ❑ Material used in walls ❑ Proximity to microwaves and cordless telephones ❑...
Page 109
❑ The 2.4 GHz band, with which Bluetooth devices or wireless LAN devices work, is used by various devices. Bluetooth devices use the technology to minimize the interference from other devices that use the same wave length. Simultaneous use of the Bluetooth function and wireless communication devices, however, may cause radio interference and result in reduced communication speeds and distances than the standard values.
Page 110
Bluetooth Security The Bluetooth wireless technology has an authentication function, which allows you to determine with whom you choose to communicate. With the authentication function, you can prevent any anonymous Bluetooth devices from accessing your computer. The first time two Bluetooth devices communicate, a common passkey (a password required for authentication) should be determined for both devices to be registered.
Using Your VAIO Computer Communicating with Another Bluetooth Device You can connect your computer to a Bluetooth device such as another computer, a mobile phone, a PDA, a headset, a mouse, or a digital camera without the use of any cables. To communicate with another Bluetooth device To communicate with another Bluetooth device, you first need to set up the Bluetooth function.
Using Peripheral Devices Using Peripheral Devices You can add functionality to your VAIO computer by using the various ports on the computer. ❑ Connecting External Speakers (page 113) ❑ Connecting a Universal Serial Bus (USB) Device (page 115) ❑ Connecting a Printer (page 117) ❑...
Connecting External Speakers You can connect external sound output devices (not supplied), such as speakers or headphones, to your computer. Since your computer is capable of outputting digital signals through the OPTICAL OUT port, you can connect an S/PDIF device such as digital headphones or an AV amplifier to the port and enhance the sound quality of your computer. For more information, see the manual that came with your S/PDIF device.
To connect external speakers Plug the speaker cable (1) (not supplied) into the headphones jack (2) i. Plug the other end of the speaker cable to the external speaker (3). Turn down the volume of the speakers before you turn them on. ✍...
Connecting a Universal Serial Bus (USB) Device To protect your computer and/or USB devices from damage, avoid exposing the USB ports to shock or impact when moving the computer with USB devices connected. Connecting a USB Floppy Disk Drive You can purchase a USB floppy disk drive and connect it to your computer. To connect a USB floppy disk drive Choose the USB port (1) you prefer to use.
Disconnecting a USB floppy disk drive You can disconnect a USB floppy disk drive when your computer is on or off. Disconnecting the drive when the computer is in Sleep mode may cause the computer to malfunction. To disconnect a USB floppy disk drive ✍...
Connecting a Printer You can connect a Windows-compatible printer to your computer to print documents. Connecting a Printer Using the USB Port You can connect a USB printer compatible with your version of Windows to the computer. To connect a printer using the USB port Plug the power cord (1) of your printer into an AC outlet.
Connecting an i.LINK Device Notes on connecting i.LINK devices ❑ Your computer is equipped with an i.LINK port, which you can use to connect an i.LINK device, such as a digital video camcorder. ❑ The i.LINK port on your computer does not supply power to an external device. If the external device requires external power, be sure to connect it to a power source.
On Sony digital video cameras, ports labeled DV Out, DV In/Out, or i.LINK are i.LINK-compatible. The Sony digital video camcorder shown here is an example. Your digital video camcorder may need to be connected differently. You cannot access the pictures stored on a Memory Stick when using an i.LINK connection.
Customizing Your VAIO Computer This section briefly describes how to change the main settings of your VAIO computer. Among other things, you will learn how to use and customize the look of your Sony software and utilities. ❑ Setting the Password (page 121) ❑...
Setting the Password Use one of the BIOS functions to set the password. Once you have set the password, you will be prompted to enter the password after the VAIO logo appears to start your computer. The power-on password allows you to protect your computer from unauthorized access. Adding the Power-on Password The power-on password is provided to protect your computer from unauthorized access.
Page 122
To add the power-on password (machine password) Turn on the computer. Press the F2 key when the VAIO logo appears. The BIOS setup screen appears. If not, restart the computer and press the F2 key several times when the VAIO logo appears.
Page 123
To add the power-on password (user password) Make sure you set the machine password before setting the user password. Turn on the computer. Press the F2 key when the VAIO logo appears. The BIOS setup screen appears. If not, restart the computer and press the F2 key several times when the VAIO logo appears.
Changing/Removing the Power-on Password To change or remove the power-on password (machine password) Turn on the computer. Press the F2 key when the VAIO logo appears. The BIOS setup screen appears. If not, restart the computer and press the F2 key several times when the VAIO logo appears.
Page 125
To change or remove the power-on password (user password) Turn on the computer. Press the F2 key when the VAIO logo appears. The BIOS setup screen appears. If not, restart the computer and press the F2 key several times when the VAIO logo appears.
Some of the control items will not be visible if you open the VAIO Control Center as a standard user. Changing the default SONY logo lamp activity The SONY logo lamp illuminates when you turn on your computer. You can change this default activity of the lamp to make it stay unlit by following these steps: Click Start, All Programs, and VAIO Control Center.
Customizing Your VAIO Computer Using the Power Saving Mode In addition to the normal operating mode, your computer has a distinct power saving mode called Sleep mode. Using Normal Mode This is the normal state of the computer when it is in use. The green power indicator light is lit in this mode.
Using Sleep Mode Sleep mode turns off the LCD screen and places the hard disk drive and the CPU into a low power consumption mode. The orange power indicator light illuminates in this mode. Turn off your computer if you do not intend to use it for a long period of time. To activate Sleep mode Click Start, the arrow next to the Lock button, and Sleep.
Page 129
If the computer is not used for a certain period of time, it will enter Sleep mode. To modify this, you can change the Sleep mode settings. To change the Sleep mode settings Click Start, Control Panel, Hardware and Sound, and Power Options. Click Change plan settings under the current power plan.
❑ You should not touch the connectors or open the memory module compartment cover. For the type of module and the amount of memory installed on your model, see the online specifications. For assistance, contact an authorized Sony Service Center. To find the nearest center or agent, see Sony Support Information (page 200).
Adding and Removing Memory If you want to expand the functionality of your computer, you can increase the amount of memory by installing optional memory modules. Before you upgrade your computer's memory, read the notes and procedures in the following pages. Notes on adding/removing memory modules ❑...
Page 132
❑ Use the special bag supplied with the memory module or wrap the module in aluminum foil to protect it from ESD. ❑ Introducing any liquids, foreign substances, or objects into the memory module slots or other internal components of your computer will result in damage to the computer and any repair costs will not be covered by the warranty.
Removing and Installing a Memory Module To change or add a memory module Shut down the computer, turn off all peripheral devices, and disconnect peripheral devices from the accessible ports and jacks. Remove the back panel cover from the computer. See Removing and Replacing the Covers Disconnect the power cord and the rest of the peripheral devices.
Page 134
Touch a metal object to discharge static electricity. Remove the currently installed memory module as follows: ❑ Pull the latches in the direction of the arrows (1). The memory module is released. ❑ Make sure that the memory module tilts up and then pull it out in the direction of the arrow (2). Upgrading Your VAIO Computer...
Page 135
Remove the new memory module from its packaging. Slide the memory module into the memory module slot and push it in until it clicks into place. Do not touch any other components on the motherboard. If you want to install only one memory module, be sure to use the lower slot. Be sure to insert the connector edge of the memory module into the slot while aligning the notch on the module with the small projection in the open slot.
Page 136
Upgrading Your VAIO Computer 10 Replace the memory module compartment cover and tighten the screw. 11 Connect the power cord and the peripheral devices that you disconnected in step 3. 12 Replace the back panel cover. See Removing and Replacing the Covers (page 20) for the procedure.
Viewing the Amount of Memory To view the amount of memory Turn on the computer. Click Start, All Programs, and VAIO Control Center. Click System Information and System Information. You can view the amount of system memory in the right pane. If the additional memory does not appear, repeat the installation procedure and restart the computer.
Installing an Additional Hard Disk Drive To install an additional hard disk drive Shut down the computer, turn off all peripheral devices, and disconnect peripheral devices from the accessible ports and jacks. Remove the back panel cover from the computer. See Removing and Replacing the Covers Disconnect the power cord and the rest of the peripheral devices.
Page 140
Unscrew the two screws (3) securing the drive holder. Pull out the drive holder (4) from the HARD DISK DRIVE ACCESS BAY and set it aside. Upgrading Your VAIO Computer...
Page 141
Place a new drive into the drive holder and align the holes on each side of the drive holder. Secure the drive to the drive holder with screws, through the holes on each side of the drive holder. A new hard disk drive comes with the necessary screws. Do not overtighten these screws when securing the drive to the drive holder. 10 Slide the drive holder into the drive bay until it clicks into place and secure it with the screws.
Page 142
Upgrading Your VAIO Computer 11 Connect the Serial ATA power cable and the Serial ATA cable. 12 Tighten the screws to secure the drive holder. 13 Replace the drive bay cover and tighten the screws. 14 Connect the power cord and the peripheral devices that you disconnected in step 3. 15 Replace the back panel cover.
Identifying the Additional Hard Disk Space When you initialize the new hard disk, it must be configured as an extended partition in Windows NT file system (NTFS) format. To identify the additional hard disk space Log on to Windows as a user with administrative rights. Click Start, right-click Computer, and select Manage.
Precautions Precautions This section describes safety guidelines and precautions to help you protect your VAIO computer from potential damage. ❑ Handling the LCD Screen (page 145) ❑ Using the Power Source (page 146) ❑ Handling Your Computer (page 147) ❑ Handling the Built-in MOTION EYE Camera (page 150) ❑...
❑ Do not change the LCD screen orientation setting in the Tablet PC Settings window even when there are change options available for selection, as this may make your computer unstable. Sony assumes no liability for any malfunctions arising from changes to the settings.
❑ Unplug your computer from the AC outlet if you are not planning to use the computer for a long period of time. ❑ Make sure that the AC outlet is easily accessible. ❑ Use the power cord supplied with your computer or genuine Sony products. Do not use any other power cord as it may cause a malfunction.
Handling Your Computer ❑ Clean the cabinet with a soft cloth, which is dry or lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine, as these may damage the finish of your computer.
Page 148
If any problems occur, unplug the computer and contact an authorized Sony Service Center. To find the nearest center or agent, see Sony Support Information ❑ Make sure you disconnect the power cord before cleaning your computer.
Page 149
❑ To avoid losing data when your computer is damaged, back up your data regularly. ❑ Do not grasp the base stand to lift your computer as the stand may break and cause the main unit to fall, resulting in damage to the computer or personal injuries.
Handling the Built-in MOTION EYE Camera ❑ Do not touch the lens protection cover of the built-in MOTION EYE camera, as it may cause scratches on the cover and such scratches will appear on the captured images. ❑ Do not let the direct sunlight get into the lens of the built-in MOTION EYE camera regardless of your computer's power state, as it may cause the camera to malfunction.
Handling Floppy Disks ❑ Do not open the shutter manually and touch the internal components of the floppy disk. ❑ Keep floppy disks away from magnets. ❑ Keep floppy disks away from direct sunlight and other sources of heat. ❑ Keep floppy disks away from any liquid. Do not let them get wet. When you are not using your floppy disk, always remove it from the floppy disk drive and put it in a storage case.
Handling Discs ❑ Do not touch the surface of the disc. ❑ Fingerprints and dust on the surface of a disc may cause read errors. Always hold the disc by its edges and central hole, as shown below: ❑ Proper care of the disc is essential to its continuous reliability. Do not use solvents (such as benzine, thinner, alcohol, commercially available cleaners, or anti-static spray) which may cause damage to the disc.
Page 153
❑ An 8 cm disc adapter exclusively designed for your model is provided for use of 8 cm discs on your computer. To attach an 8 cm disc to the adapter With its label facing upward, attach the disc to the adapter (VAIO logo side up) by pulling each of the tabs (1) and (2) outward.
Page 154
Press the tabs (indicated by the arrows below) and then make sure the disc is level with the surface of the adapter. Notes on using the 8 cm disc adapter ❑ Be sure to attach an 8 cm disc to the adapter before using it on your computer. Not using the supplied adapter or using a similar kind of the adapter with the disc may cause a disc recognition error or result in a stuck disc, a damaged disc, or a malfunction of your computer.
Precautions Using Headphones Preventing hearing damage – Avoid using headphones at high volume. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, reduce the volume or discontinue use.
Handling the Memory Stick ❑ Do not touch the Memory Stick connector with your finger or metallic objects. ❑ Use only the adhesive label supplied with the Memory Stick as a label. ❑ Do not bend, drop, or expose the Memory Stick. ❑...
Handling the Hard Disk The hard disk drive has a high storage density and reads or writes data in a short time. However, it can be easily damaged by mechanical vibration, shock, or dust. Although the hard disk drive has the internal safety device to prevent losing data due to mechanical vibration, shock, or dust, you should be careful when handling your computer.
Updating Your Computer Be sure to install the latest updates on your computer with the following software applications so that the computer can run more efficiently. ❑ Windows Update Click Start, All Programs, and Windows Update and then follow the on-screen instructions. ❑...
Troubleshooting This section describes how to solve common problems you might encounter when using your VAIO computer. Many problems have simple solutions. Try these suggestions before visiting the Sony online support web site at the following URLs: http://esupport.sony.com/EN/VAIO/ for customers in USA http://www.sony.ca/support/...
❑ Condensation may cause your computer to malfunction. If this occurs, do not use the computer for at least one hour. ❑ Check that you are using the supplied Sony power cord. For your safety, use only the genuine Sony power cord, which is supplied by Sony for your VAIO computer.
Page 162
What should I do if the green power indicator light turns on but my screen remains blank? ❑ If the orange DISPLAY OFF indicator is lit, press the DISPLAY OFF button. ❑ Make sure the computer input is selected. To change the display input, press the HDMI SELECT button on the right of the computer.
Page 163
What should I do if my computer or software stops responding? ❑ If your computer stops responding while a software application is running, press the Alt+F4 keys to close the application window. ❑ If the Alt+F4 keys do not work, click Start, the arrow next to the Lock button, and Shut Down to turn off your computer. ❑...
Why doesn't my computer enter Sleep mode? Your computer may become unstable if the operating mode is changed before the computer completely enters Sleep mode. To restore your computer to normal mode Close all open programs. Click Start, the arrow next to the Lock button, and Restart. If your computer does not restart, press the Ctrl+Alt+Delete keys and click the arrow next to the Shut down button and Restart.
What should I do if I cannot remember the power-on password? If you have forgotten the power-on password, contact an authorized Sony Service Center to reset it. A reset fee will be charged. To find the nearest center or agent, see Sony Support Information How can I change the boot device order? You can use one of the BIOS functions to change the boot device order.
Why doesn't my screen turn off after the automatic turn-off time has passed? The VAIO original screen saver disables the timer setting, which you can select using the Windows power options, for your screen to turn off. Select a screen saver other than the VAIO original screen saver. What should I do if I cannot boot my computer from the USB floppy disk drive connected to the computer? To boot your computer from the USB floppy disk drive, you need to change the boot device.
System Security How can I protect my computer against security threats, such as viruses? The Microsoft Windows operating system is preinstalled on your computer. The best way to protect your computer against security threats, such as viruses, is to download and install the latest Windows updates regularly. You can get important Windows updates by doing the following: Your computer must be connected to the Internet to download the updates.
Built-in MOTION EYE Camera Why does the viewer window show no images or poor-quality images? ❑ The built-in MOTION EYE camera cannot be shared by more than one software application. If another software application is using the camera, exit the application before using the built-in MOTION EYE camera. ❑...
Page 169
Troubleshooting Why do the images captured by the built-in MOTION EYE camera flicker? This problem occurs when you use the camera under fluorescent lights due to the mismatch between lighting output frequency and shutter speed. To reduce flicker noise, change the direction of the camera or the brightness of camera images. In some software applications, you can set an appropriate value to one of the camera properties (e.g.
Networking What should I do if my computer cannot connect to a wireless LAN access point? ❑ Connection capability is affected by distance and obstructions. You need to place your computer away from obstructions or move any access point you may be using closer to the computer. ❑...
What should I do if I cannot access the Internet? ❑ Check the access point settings. See the manual that came with your access point for more information. ❑ Make sure your computer and the access point are connected to one another. ❑...
❑ Wireless LAN communication uses divided frequency bands known as channels. Third-party wireless LAN access point channels may be preset to different channels from Sony devices. ❑ If you are using a wireless LAN access point, see connectivity information contained in the manual that came with your access point.
Bluetooth Technology What should I do if other Bluetooth devices cannot find my computer? ❑ Make sure both devices have the Bluetooth function enabled. ❑ If the WIRELESS indicator light is unlit, turn on the WIRELESS switch. ❑ Your computer and the device may be too far apart. Wireless Bluetooth technology works best when the devices are within 33 feet (10 meters) of each other.
Page 174
What should I do if other Bluetooth devices cannot connect to my computer? ❑ Make sure the other devices are authenticated. ❑ To allow other Bluetooth devices to communicate with your computer, follow these steps: Click Start, Control Panel, Hardware and Sound, Bluetooth Devices, and Bluetooth Settings. Click the Options tab and select the Allow Bluetooth devices to find this computer check box.
Why is my Bluetooth connection slow? ❑ The data transfer speed depends on the obstructions and/or the distance between the two devices, on the radio wave quality, and on the operating system or the software in use. Move Bluetooth devices closer to your computer. ❑...
Page 176
Troubleshooting Why can't I use the Bluetooth devices when I switch users? If you switch users without logging off your system, the Bluetooth devices will not work. Be sure to log off before switching users. To log off your system, click Start, the arrow next to the Lock button, and Log Off. Why can't I exchange business card data with a mobile phone? The business card exchange function is not supported.
Optical Discs Why does my computer freeze when I try to read a disc? The disc that your computer is trying to read may be dirty or damaged. Follow these steps: Press the Ctrl+Alt+Delete keys and click the arrow next to the Shut down button and Restart to restart the computer. Remove the disc from the optical disc drive.
Page 178
What should I do if I cannot play a disc properly on my computer? ❑ Make sure the disc is inserted into the optical disc drive with the label side facing toward you. ❑ Make sure the necessary program(s) is installed according to the manufacturer's instructions. ❑...
Page 179
Click Device Manager in the left pane. The Device Manager window appears with a listing of your computer's hardware devices. If an "X" or an exclamation point appears on the listed device, you may need to enable the device or reinstall the drivers.
Page 180
What should I do if I cannot play Blu-ray Disc media or my computer becomes unstable during Blu-ray Disc playback? You may not be able to play some Blu-ray Disc contents on your computer, or the computer may become unstable during Blu-ray Disc playback.
Display Why did my screen go blank? ❑ Your computer screen may go blank if the computer enters Sleep mode. If the computer is in Sleep mode, press any key to bring the computer back into Normal mode. See Using the Power Saving Mode ❑...
Printing What should I do if I cannot print a document? ❑ Make sure your printer is on, and the printer cable is securely connected to the ports on the printer and your computer. ❑ Make sure your printer is compatible with the Windows operating system installed on your computer. ❑...
Microphone What should I do if my microphone does not work? ❑ If you are using an external microphone, make sure the microphone is turned on and is properly plugged into the microphone jack on your computer. ❑ Your sound input device may have been incorrectly configured. To configure the sound input device, follow these steps: Close all open programs.
Troubleshooting Mouse What should I do if my computer does not recognize my mouse? ❑ Make sure the power switch on the bottom of the wireless mouse is in the ON position. ❑ Make sure another mouse is not connected. ❑...
Page 185
What should I do if the pointer does not move when I use my mouse? ❑ Make sure another mouse is not connected. ❑ If the pointer does not move while a software application is running, press the Alt+F4 keys to close the application window. ❑...
Speakers What should I do if my external speakers do not work? ❑ If you are using a program that has its own volume control, make sure the volume control is properly set. See the program's help file for more information. ❑...
Page 187
What should I do if I do not hear sound from the built-in speakers? ❑ If you are using a program that has its own volume control, make sure the volume control is properly set. See the program's help file for more information. ❑...
Touch Pad What should I do if the touch pad does not work? ❑ You may have disabled the touch pad. Press the Fn+F11 keys to enable the touch pad. ❑ If the pointer does not move while a software application is running, press the Alt+F4 keys to close the application window. ❑...
Keyboard What should I do if the keyboard configuration is wrong? The language layout of your wireless keyboard is labeled on the packaging box. If you choose a different regional keyboard when you complete the Windows setup, the key configuration will be mismatched. To change the keyboard configuration, follow these steps: Click Start and Control Panel.
Page 190
Troubleshooting What should I do if my computer does not recognize my keyboard? ❑ Make sure the power switch on the back of the wireless keyboard is in the ON position. ❑ Make sure the supplied AA batteries are properly installed. ❑...
Floppy Disks Why doesn't the Safely Remove Hardware icon appear on the taskbar when the drive is connected? Your computer does not recognize the floppy disk drive. First, make sure the USB cable is properly connected to the USB port. If you need to secure the connection, wait a few moments for the computer to recognize the drive. If the icon still does not appear, follow these steps: Close all programs that are accessing the floppy disk drive.
✍ i.LINK is a trademark of Sony Corporation used only to designate that a product contains an IEEE 1394 connection. The procedure to establish an i.LINK connection may vary, depending on a software application, an operating system, and a compatible i.LINK device. Not all products with an i.LINK connection can communicate with each other.
How do I change the sound output device? If you do not hear sound from the device connected to a port, such as the USB port, HDMI output port, optical output port, or headphones jack, you need to change the device for sound output. Close all open programs.
Page 194
What should I do if I do not hear the sound from the sound output device connected to the HDMI output port, optical output port, or headphones jack? You need to change the sound output device if you want to hear sound from the device connected to a port, such as the HDMI output port, optical output port, or headphones jack.
Page 195
Troubleshooting Why do sound interruptions and/or dropped frames occur when I play high-definition videos, such as those recorded with the AVCHD digital video camcorder? Playing high-definition videos requires substantial hardware resources, such as CPU, GPU, or system memory performance on your computer. During the video playback, some operations and/or functions may become unavailable, and sound interruptions, dropped frames, and playback failure may occur depending on your hardware specifications.
HDMI Input What should I do if I cannot change the volume with the Up/Down buttons? You cannot change the volume with the Up/Down buttons while the computer input is selected. Press the HDMI SELECT button on the right of the computer to switch the display input to the HDMI input. ✍...
Page 197
How do I turn off the Sony logo lamp while viewing the HDMI input? You need to change the settings with the OSD menu to turn off the Sony logo lamp. See Changing the Display and Sound Settings for the HDMI Input (page 83) for more information.
Use of recorded music requires permission from the copyright holders. Sony is not responsible for music files that cannot be recorded from a CD or downloaded from other sources. Can I copy images from a digital camera using a Memory Stick? Yes, and you can view video clips that you have recorded with Memory Stick-compatible digital cameras.
Peripherals What should I do if I cannot connect a USB device? ❑ If applicable, check the USB device is turned on and using its own power supply. For example, if you are using a digital camera, check if the battery is charged. If you are using a printer, check if the power cable is connected properly to the AC outlet.
This service provides instant access to information on commonly encountered problems. Type a description of the problem and the Knowledge Database searches for the corresponding solutions online. You can visit the Sony online support web site at the following URLs: http://esupport.sony.com/EN/VAIO/ http://www.sony.ca/support/...
Page 201
VAIO Update When your computer is connected to the Internet, VAIO Update automatically notifies you when critical software and security information is posted on the support web site. Click the VAIO Update notice to open the VAIO Support web site and view the information.
Page 202
For customers in Latin American countries or areas Customer Information Center If you do not find the information you are looking for at our site, you may call Sony directly. In order to receive the fastest and most efficient services, have the following information readily available: Your VAIO computer model You can find it at the lower right corner of the display on the computer.
Page 203
❑ Chile: 800-261-800 02-754-6333 (from mobile phones) ❑ Colombia: 358-1251 (in Bogota) 01-8000-94-00-11 ❑ Mexico: 5002-9819 (in Mexico City) 01-800-759-7669 (in other cities) ❑ Panama: 800-2050 800-7669 (800-SONY) ❑ Peru: 0-801-1-7000 511-6100 ❑ Venezuela: 0-800-1-SONY-00 (0-800-1-7669-00) Support Options...
Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. SD Logo is a trademark. SDHC Logo is a trademark. The ExpressCard word mark and logos are owned by the PCMCIA and any use of such marks by Sony Corporation is under license.
Page 205
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. "AVCHD" is a trademark of Panasonic Corporation and Sony Corporation. All other names of systems, products, and services are trademarks of their respective owners. In the manual, the ™ or ®...