Input Fader Request - Sony SRP-X500P Interface Manual

•
FADER (1st-6th byte)
The level for each fader can be specified (in dB units).
The parameter and levels are as shown in the following table.
Level
-∞
-70.0
-60.0
-55.0
-50.0
-45.0
-40.0
-35.0
-32.5
-30.0
-27.5
-25.0
-24.0
-23.0
-22.0
-21.0
Example
To set the level for each input fader as follows:
MIC 1/WL 1 INPUT : -10dB
MIC 2/WL 2 INPUT : -10dB
MIC 3 INPUT : -10dB
MIC 4 INPUT : -10dB
LINE INPUT : 0dB
AV/RGB INPUT : 0dB
0x43 0x50 0x4D 0x35 0x4A 0x4A 0x4A 0x4A 0x59 0x59 0x0D
('C P M 5 J J J J Y Y CR')
2.1.4 INPUT FADER REQUEST : 0x52 0x50 0x4D 0x35 ('RPM5')
This command is used to read the input fader settings from the SRP-X500P.
Packet format
0x52 0x50 0x4D 0x35 0x0D
Return packet format
When the SRP-X500P receives the command successfully, the parameter is returned together with an ACK (0x41
('A')) in the order shown below.
0x41 parameter" 0x0D
"
The parameter consists of 6 bytes of data which are the same as those of the parameter of the INPUT FADER
command.
SRP-X500P RS-232C Interface Manual
Level
0x30 ('0') -20.0 0x40 ('@')
0x31 ('1') -19.0 0x41 ('A')
0x32 ('2') -18.0 0x42 ('B')
0x33 ('3') -17.0 0x43 ('C')
0x34 ('4') -16.0 0x44 ('D')
0x35 ('5') -15.0 0x45 ('E')
0x36 ('6') -14.0 0x46 ('F')
0x37 ('7') -13.0 0x47 ('G')
0x38 ('8') -12.0 0x48 ('H')
0x39 ('9') -11.0 0x49 ('I')
0x3A (':') -10.0 0x4A ('J')
0x3B (';') -9.0 0x4B ('K')
0x3C ('<') -8.0 0x4C ('L')
0x3D ('=') -7.0 0x4D ('M')
0x3E ('>') -6.0 0x4E ('N')
0x3F ('?') -5.0 0x4F ('O')
Page 8/43
Level Level
-4.5 0x50 ('P') +3.5
-4.0 0x51 ('Q') +4.0
-3.5 0x52 ('R') +4.5
-3.0 0x53 ('S') +5.0
-2.5 0x54 ('T') +5.5
-2.0 0x55 ('U') +6.0
-1.5 0x56 ('V') +6.5
-1.0 0x57 ('W') +7.0
-0.5 0x58 ('X') +7.5
0 0x59 ('Y') +8.0
+0.5 0x5A ('Z') +8.5
+1.0 0x5B ('[') +9.0
+1.5 0x5C ('\') +10.0
+2.0 0x5D (']')
+2.5 0x5E ('^')
+3.0 0x5F ('_')
0x60 ('`')
0x61 ('a')
0x62 ('b')
0x63 ('c')
0x64 ('d')
0x65 ('e')
0x66 ('f')
0x67 ('g')
0x68 ('h')
0x69 ('i')
0x6A ('j')
0x6B ('k')
0x6C ('l')