Rear Panel - Sony SRP-X700P Operating Instructions Manual

Location and function of parts

Rear panel

qh
ANT IN a
DC
9V OUT
35mA MAX
S VIDEO
VIDEO
5
A
LINE3 IN
L L
4
R R
1
+48V
ON OFF
1
1 MIC INPUT 1 and MIC INPUT 2 terminals
The microphone input terminals.
The wireless microphone has the first priority when the tuner
unit is installed but you can use the wired microphone up until
you turn ON the POWER of the wireless microphone.
2 MIC INPUT 3 and MIC INPUT 4 terminals
The microphone input terminals.
3 MIC 5/LINE 1 IN and MIC 6/LINE 2 IN
terminals
The microphone and line input terminals.
You can select the input level of these input terminals with the
ql MIC/LINE selector button. When you select the
microphone level, the DC +48 V power is output to the
condenser microphone automatically.
By default, they are set to the LINE (4).
4 LINE 3 IN terminals
The input terminals for audio products.
5 LINE 4 INPUT terminals
The input terminals for AV equipment.
As to the video input signals, the combination of composite
signal and S video signal or the combination of component
signal and RGB signal is selected by the SRP-X700P Manager
for each channel.
• 4A, 4B and 4C input terminals
The video input terminals for accepting the composite and
S video signals, and the stereo audio input terminal.
By default, they are set to –10 dBu with the composite
signal.
• 4D and 4E input terminals
The video input terminals for accepting the component and
RGB signals, and the audio input terminal accepting the 5.1-
channel surround audio signal.
By default, 4D is set to –10 dBu with the component signal
and 4E is set to –10 dBu with the RGB signal.
• 4F input terminal
The video input terminals for accepting the component and
RGB signals, and the stereo audio input terminal.
By default, it is set to –10 dBu with the RGB signal.
6
LINE4 INPUT
COMPONENT/RGB
B C D E
FRONT REAR FRONT REAR
CENTER CENTER
L L L
WOOFER WOOFER
R R R
MIC INPUT
2 3 4
+48V +48V +48V
ON OFF ON OFF ON OFF
2
qk
qa 0
ANT IN b OUTPUT
DC
9V OUT
35mA MAX S VIDEO VIDEO
R/R-Y G/Y B/B-Y SYNC/HD
F
CONTROL S
PROJECTOR CONTROL
OUTPUT CONTROL S
1 3
IN
RS-232C
L
2 4 OUT
R
MIC5/LINE1 IN MIC6/LINE2 IN
1
(+48V) (+48V)
MIC MIC
LINE LINE
3 6
ql qs
<LINE4 INPUT COMPONENT/RGB terminal>
Pin No.
1
2
3
4
5
6
7
8
6 LINE OUTPUT 1 and LINE OUTPUT 2 terminals
The audio output terminals.
7 LINE OUTPUT 3 to LINE OUTPUT 8 terminals
The audio output terminals.
8 REC OUT terminal
The audio output terminal.
Usually, connect this terminal to an MD unit for recording.
9 SPEAKERS terminal
The output terminal of the internal power amplifier.
You can connect a high impedance speaker (70 V LINE). (In
the case of high impedance speaker 70 V LINE, the output
signal becomes monaural.) You can select the output signal
and operating mode with the SRP-X700P Manager.
By default, the operating mode is set to Lo impedance and the
output signal is set to LINE OUT1 and LINE OUT2.
For the speaker connection, see "Connecting the Speaker" on
page 11.
qd 9
SPEAKERS
CH-2 CH-1
IMPEDANCE USE IMPEDANCE USE
4-16 4-16
VD
70V LINE
IMPEDANCE USE 32 -10k
REMOTE
PARALLEL RS-232C
LINE OUTPUT REC OUT
3 5 7 1
2
4 6 8 2
7 8 qf qj
(HD D-sub 15-pin, female)
Function Pin No.
9
Video input R/R-Y N.C
Video input G/Y 10 GND
Video input B/B-Y 11 N.C
GND 12 N.C
N.C
Composite sync signal/
13
horizontal sync signal, SYNC/HD
GND
GND 14 Vertical sync signal VD
GND 15 N.C
w;
CIRCUIT
BREAKER
PUSH RESET
qg
AC IN
Function