INVT Goodrive 35 Series Operation Manual page 266

Goodrive35 inverters
unshielded twisted multipair cable (Fig b) is also usable. However, for frequency input, always use a
shielded cable.
Note: Run analog and digital signals in separate cables.
The relay cable needs the cable type with braided metallic screen.
The keypad needs to connect with cables. It is recommended to use the screen cable on complex
electrical magnetic condition.
Do not make any voltage tolerance or insulation resistance tests (for example hi-pot or megger) on
any part of the drive as testing can damage the drive. Every drive has been tested for insulation
between the main circuit and the chassis at the factory. Also, there are voltage-limiting circuits inside
the drive which cut down the testing voltage automatically.
Check the insulation of input power cable according to local regulations before connecting to the drive.
D.4.2.1 The inverters of AC 3PH 380 V (-15%) – 440 V (+10%)
Model
GD35-1R5G-4-C1/D1/H1
GD35-2R2G-4-C1/D1/H1
GD35-004G-4-C1/D1/H1/H2
GD35-5R5G-4-C1/D1/H1/H2
GD35-7R5G-4-
C1/D1/H1/H2
GD35-011G-4-
C1/D1/H1/H2
GD35-015G-4-C1/D1/H1/H2
GD35-018G-4-C1/D1/H1/H2
GD35-022G-4-C1/D1/H1/H2
GD35-030G-4-C1/D1/H1/H2
GD35-037G-4-C1/D1/H1
GD35-045G-4-C1/D1/H1
GD35-055G-4-C1/D1/H1
GD35-075G-4-C1/D1/H1
GD35-090G-4-C1/D1/H1
GD35-110G-4-C1/D1/H1
Recommended
cable size Connecting cable size (mm
2
(mm )
RST RST
PE
UVW UVW
2.5 – 6 2.5 – 6 2.5 – 6 2.5 – 6
2.5 2.5
2.5 – 6 2.5 – 6 2.5 – 6 2.5 – 6
2.5 2.5
2.5 – 6 2.5 – 6 2.5 – 6 2.5 – 6
2.5 2.5
2.5 – 6
2.5 2.5
4 – 16
4 4
6 – 16
6 6
10 – 25 10 – 25 10 – 25 6 – 25
10 10
16 – 25 16 – 25 16 – 25 10 – 25
16 16
16 – 25 16 – 25 16 – 25 10 – 25
16 16
16 – 25 16 – 25 16 – 25 16 – 25
25 16
25 – 50 25 – 50 25 – 50 16 – 50
25 16
25 – 50 25 – 50 25 – 50 16 – 50
35 16
50 – 95 50 – 95 50 – 95 25 – 50
50 25
70 – 95 70 – 95 70 – 95 35 – 50
70 35
95 –
95 50
150
95 –
120 70
300
259
Appendix D Peripheral options and parts
PB
P1, (+) (+), PE
(-)
4 – 6 4 – 6 2.5 – 6
4 – 16 4 – 16 4 – 16
6 – 16 6 – 16 6 – 16
95 – 95 – 50 –
150 150 150
95 – 95 – 70 –
300 300 240
2
)
Tightening
Terminal
torque
screw
(Nm)
1.2 – 1.5
M4
1.2 – 1.5
M4
1.2 – 1.5
M4
1.2 – 1.5
M4
2 – 2.5
M5
2 – 2.5
M5
2 – 2.5
M5
2 – 2.5
M5
4 – 6
M6
4 – 6
M6
9 – 11
M8
9 – 11
M8
9 – 11
M8
18 – 23
M10
18 – 23
M10
18 – 23
M10