Multiple Remote Control; Function Setting; Function Details - Fujitsu AUXG-KRLB Series Installation Manual

(a) 2-wire type
DIP switch (RC AD SW)...Factory setting "00"
Since the remote controller address settings are automatically confi gured, you do not
need to confi gure them.
If confi guring manually, it is necessary to confi gure both the indoor unit and the remote
controller. For details, please refer to the remote controller installation manual.
(b) 3-wire type
DIP switch (RC AD SW)...Factory setting "00"
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from "00".
Setting Setting range
Remote controller
00 to 15
address
Example
If 4 indoor units are connected.
Indoor unit 1 Indoor unit 2
RC AD SW RC AD SW
00 01
Remote
controller
Set the R.C. address in accordance with the table below.
Indoor unit R.C. address
1
1 00 OFF
2 01 ON
3 02 OFF
4 03 ON
5 04 OFF
6 05 ON
7 06 OFF
8 07 ON
9 08 OFF
10 09 ON
11 10 OFF
12 11 ON
13 12 OFF
14 13 ON
15 14 OFF
16 15 ON
NOTES:
Be sure to set consecutive R.C. address.
The indoor units cannot be operated if a number is skipped.

6. 2. Multiple remote control

Up to 2 remote controllers can be used to operate the indoor units.
Multiple installation method described above is prohibited to combine 3 Wired type
with 2 Wired Type.
I.U.
A
Master
A, B : Remote controller cable. (Refer to 2. 4. Electrical requirement.)
A ≤ 500 m, A+B ≤ 500 m
Switch 100
ON
Setting
example 00
1 2 3 4
RC AD
Indoor unit 3 Indoor unit 4
RC AD SW RC AD SW
03
02
DIP SWITCH No.
2 3
OFF OFF OFF
OFF OFF OFF
ON OFF OFF
ON OFF OFF
OFF ON OFF
OFF ON OFF
ON ON OFF
ON ON OFF
OFF OFF ON
OFF OFF ON
ON OFF ON
ON OFF ON
OFF ON ON
OFF ON ON
ON ON ON
ON ON ON
CAUTION
I.U.
A B
Master Slave

7. FUNCTION SETTING

Refer to the installation manual of remote controller for setting method.

7. 1. Function Details

■ Filter sign
Select appropriate intervals for displaying the fi lter sign on the indoor unit according to the
estimated amount of dust in the air of the room.
If the indication is not required, select "No indication" (03).
Function Setting
number
11
■ Ceiling height
Select the appropriate ceiling height according to the place of installation.
Function Setting
number
20
4
The ceiling height values are for the 4-way outlet.
Do not change this setting in the 3-way outlet mode.
■ Outlet directions
Select the appropriate number of outlet directions according to the installation conditions.
Function Setting
number
22
■ Vertical wind direction adjustment range
To prevent draft, change the setting to "Upward" (01).
Note that the airfl ow in certain usage conditions may leave the ceiling dirty. In such cases,
the use of the optional "PANEL SPACER KIT" is recommended.
Function Setting
number
23
Standard
Upward
(♦... Factory setting)
Setting description
value
00 Standard (2500 hours)
01 Long interval (4400 hours)
02 Short interval (1250 hours)
03 No indication
(♦... Factory setting)
Setting description
value
Standard (3.0 m : 18/24 type)
00
(3.2 m : 30/36/45/54 type)
High ceiling (3.5 m : 18/24 type)
01
(4.2 m : 30/36/45/54 type)
02 Low ceiling (2.7 m)
(♦... Factory setting)
Setting description
value
00 4-way
01 3-way
(♦... Factory setting)
Setting description
value
00 Standard
01 Upward
Ceiling
UP
Swing range
Outlet cross section
♦
♦
♦
♦
En-13