Page 2
1. Introduction This operation manual shows on what you should pay attention during installation, operation and maintenance of solid set sprinkler irrigation systems. In spite that maintenance and operating of impact sprinklers require less attention, there are some details you should pay attention to, so that the installation fulfils its function and works to your complete satisfaction during a long period. TDP079e Rev. 26.03.2019 Page 2 / 8 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
Page 3
= part circle sprinkler (30‐360°) WR = part circle sprinkler flip up control lever Type of trajectory angle part circle sprinkler F = full circle sprinkler with tripod sprinkler flip up control lever WF = part circle sprinkler with tripod TDP079e Rev. 26.03.2019 Page 3 / 8 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
2.1 Installation When connecting to the public supply network, observe the local regulations Pipes are to be laid in a sand bed on stony ground. The sand bed should surround the pipe 10 cm on all sides When installing the sprinkler, e.g. on a standpipe, make sure that the sprinkler head can easily be turned by hand. Sprinkler Sprinkler Riser pipe Riser pipe Perrot Cardan PE‐pipe Quick coupling pipe Flush the pipes proper before installation of the sprinklers 3. Commissioning Pipes must always be filled slowly, that means you must open the gate valve gradually, under observance of the assigned operating pressure. Despite of a thoroughly flushing it may happen that the sprinkler nozzle may clog. To clean the nozzle, you must unscrew ...
Page 5
4.1 Watering arc (setting range 30‐360°) The arc of the part circle sprinklers is adjusted by pressing against the spring stopper, which widens the spring. A rough alignment is possible before installation, the fine adjustment should be made with the sprinkler running 4.2 Radius range The radius range is set using different nozzles and pressures. For further information see data sheet 4.3 Jet deflector screw (not available for all sprinkler models) The jet deflector screw is for adjustment of the irrigation near the sprinkler. If the screw is turned further into the water jet, the precipitation close to of the sprinkler is increased and the radius will be reduced 5. Maintenance / Cleaning / Repair Check the sprinkler function at regular intervals If the sprinkler or the turning device gets dirty, it should only be rinsed with clear water. Do not use lubricants or grease, as this will damage the sliding discs in the sprinkler!!! Remove and repair defective parts immediately or return for repair TDP079e Rev. 26.03.2019 Page 5 / 8 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
I f the sprinkler does not turn, there are usually dirt particles in the nozzle. Unscrew nozzle and clean! I f the sprinkler only turns in one direction and then stops, either the turning device is blocked, or the pressure is too low. Clean the turning device with clean water or compressed air (only for part circle sprinklers). Subject to change without prior notice. TDP079e Rev. 26.03.2019 Page 6 / 8 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...