Sony MDS-PC3 M-crew Service Manual
Sony MDS-PC3 M-crew Service Manual

Sony MDS-PC3 M-crew Service Manual

Dat / minidisc decks: mini size md recorder

Advertisement

Quick Links

SERVICE MANUAL
US and foreign patents licensed form Dolby Laboratories
Licensing Corporation.
System
Disc
Laser
Laser output
Laser diode
Revolutions (CLV)
Error correction
Sampling frequency
Coding
Modulation system
Number of channels
Frequency response
Signal-to-noise ratio
Wow and flutter
Inputs
LINE (ANALOG) IN
DIGITAL (OPTICAL) IN Connector type: square optical
Outputs
LINE (ANALOG) OUT (VARIABLE)
DIGITAL (OPTICAL) OUT
PHONES
Photo: SILVER

SPECIFICATIONS

General
MiniDisc digital audio system
MiniDisc
Where purchased
Semiconductor laser (λ = 780 nm)
Emission duration: continuous
U.S.A. and Canada
Less than 44.6 µW*
Other countries
* This output is the value
measured at a distance of
* Using an AC power adaptor (supplied)
200 mm from the objective lens
surface on the Optical Pick-up
Power consumption
Block with 7 mm aperture.
Dimensions (approx.)
Material: GaAlAs
400 rpm to 900 rpm
Advanced Cross Interleave Reed
Mass (approx.)
Solomon Code (ACIRC)
44.1 kHz
Supplied
Adaptive Transform Acoustic
Coding (ATRAC)
EFM (Eight-to-Fourteen
Modulation)
2 stereo channels
5 to 20,000 Hz ±0.5 dB
Over 94 dB during playback
Below measurable limit
Jack type: stereo-mini
Impedance: 47 kilohms
Rated input: 500 mVrms
Minimum input: 125 mVrms
Impedance: 660 nm (optical wave
length)
Jack type: stereo-mini
Rated output: 1 Vrms (at
50 kilohms)
Load impedance: Over 10 kilohms
Connector type: square optical
Rated output: –18 dBm
Impedance: 660 nm (optical wave
length)
Jack type: stereo-mini
Rated output: 5 mW
Load impedance: 32 ohms
MDS-PC3
Model Name Using Similar Mechanism
MD Mechanism Type
Optical Pick-up Type
Power requirements*
120 V AC, 60 Hz
220 – 230 V AC, 50/60 Hz
7 W
152 × 52 × 255 mm (6 × 2
1
10
/
inches) (w/h/d) incl.
8
projecting parts and controls
1.0 kg (2 lb 4 oz)
accessories
• AC power adaptor (1)
• Audio connecting cord
(stereo mini-plug × 1 y stereo mini-plug × 1)
(1)
• Optical cable (1)
• Remote commander (remote) RM-D52M (1)
• PC connecting kit PCLK-MN10* (1)
* Required for operation by personal computer. For
details, refer to the operating instructions supplied
with the PCLK-MN10.
US Model
Canadian Model
AEP Model
UK Model
E Model
MDS-JE640
MDM-7A
KMS-260B/J1N
×
1
/
8
MINIDISC DECK

Advertisement

Table of Contents
loading

Summary of Contents for Sony MDS-PC3 M-crew

  • Page 1: Specifications

    SERVICE MANUAL US and foreign patents licensed form Dolby Laboratories Licensing Corporation. System MiniDisc digital audio system Disc MiniDisc Laser Semiconductor laser (λ = 780 nm) Emission duration: continuous Less than 44.6 µW* Laser output * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up...
  • Page 2 If the code and message alternate, find them in the following table and perform the indicated countermeasure. Should the problem persist, consult your nearest Sony dealer. Three-digit code/Message...
  • Page 3 1. While pressing the AMS knob and x/Z button, connect the power plug to the outlet, and release the AMS knob and x/Z button. When the test mode is set, “[Check]” will be displayed. 2. Rotate the AMS knob and when “[Service]” is displayed, press the @/1 button. 3.
  • Page 4: Table Of Contents

    Table of Error Codes Error Code Description Could not load Loading switches combined incorrectly Timed out without reading the top of PTOC Could read top of PTOC, but detected error Timed out without accessing UTOC Timed out without reading UTOC Error in UTOC Could not start playback Error in sector...
  • Page 5 LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
  • Page 6 JIG FOR CHECKING BD BOARD WAVEFORM The special jig (J-2501-196-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to be performed are shown as follows. GND : Ground I+3V : For measuring Iop (Check the deterioration of the optical pick-up laser) : For measuring Iop (Check the deterioration of the optical pick-up laser) : TRK error signal (Traverse adjustment) : Reference level for checking the signal...
  • Page 7 Iop DATA RECORDING AND DISPLAY WHEN OPTICAL PICK-UP AND NON-VOLATILE MEMORY (IC195 OF BD BOARD) ARE REPLACED The Iop value labeled on the optical pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need to look at the value on the label of the optical pick-up.
  • Page 8 CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in “5 Electrical Adjustments”. • 5-6-2. Laser power check (see page 27) •...
  • Page 9 RETRY CAUSE DISPLAY MODE • In this test mode, the causes for retry of the unit during recording can be displayed on the indication vessel. During playback, the “track mode” for obtaining track information will be set. This is useful for locating the faulty part of the unit. •...
  • Page 10 Reading the Track Mode Display Higher Bits Lower Bits Hexadecimal b7 b6 b5 b4 b3 b2 b1 b0 Binary Reading the Display: Convert the hexadecimal display into binary display. If more than two causes, they will be added. Example When 84 is displayed: Higher bit : 8 = 1000 t b7 Lower bit : 4 = 0100 t b2 In this case, as b2 and b7 are 1 and others are 0, it can be determined that the retry cause is combined of “Emphasis OFF”, “Monaural”,...
  • Page 11: General

    SECTION 2 This section is extracted from instruction manual. GENERAL Location and Function of Parts...
  • Page 12 Location and Function of Parts...
  • Page 13 Getting Started...
  • Page 14: Disassembly

    SECTION 3 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 3-1. CASE (U) 4 case (U) claws 1 three screws (BVTP 3x10) 1 three screws (BVTP 3x10) 3-2. MD MECHANISM DECK (MDM-7A) 1 flat type wire (23 core) (CN102) 2 two screws 2 two screws...
  • Page 15: Main Board

    3-3. MAIN BOARD 2 two screws (BVTP 3x8) 3-4. OVER LIGHT HEAD (HR901), BD (MD) BOARD 4 Removal the solders 4 Removal the solders 1 flat type wire (13 core) (CN103) 4 MAIN board 3 head, over light (HR901) 5 two screws (BTP 2x6) 3 three screws (BVTP 3x8)
  • Page 16: Holder Assy

    3-5. HOLDER ASSY 2 claw 6 holder assy 4 boss 4 boss 1 spring (holder), tension 3-6. LOADING MOTOR ASSY (M103) 1 belt (loading) 2 two screws (PWH 1.7x2.5) 3 motor assy, loading (M103)
  • Page 17: Sled Motor Assy (M102), Slider

    3-7. SLED MOTOR ASSY (M102), SLIDER 1 two screws (BTP 2x6) 3-8. OPTICAL PICK-UP (MD) (KMS-260B/JIN) 1 FLEXBLE boaed 0 slider (SL) 2 screw (M 1.7), tapping 4 slider (EJ) 6 slider 2 guide (L) 7 lever (CHG) qa optical pick-up 9 screw (P 1.7x6) 6 two screws...
  • Page 18: Spindle Motor Assy (M101)

    3-9. SPINDLE MOTOR ASSY (M101) 2 motor assy, spindle (M101) 1 screw (M 1.7), tapping...
  • Page 19: Test Mode

    *Note: As this unit has only a few buttons, one button is assigned with several functions in the test mode.” Press the z button, AMS knob to switch the functions. • Each time the z button is pressed, the display switches in the follwing order, “PGM” t “blank” t “PGM” t –. •...
  • Page 20 4-5. SELECTING THE TEST MODE There are 26 types of test modes as shown below. The groups can be switched by rotating the AMS knob. After selecting the group to be used, press the @/1 button. After setting a certain group, rotating the AMS knob switches between these modes. Refer to “Group”...
  • Page 21 4-5-1. Operating the Continuous Playback Mode 1. Entering the continuous playback mode 1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.) 2 Rotate the AMS knob and display “CPLAY1MODE”(C34). 3 Press the @/1 button to change the display to “CPLAY1 MID”. 4 When access completes, the display changes to “C = Note : The numbers “...
  • Page 22 4-6. FUNCTIONS OF OTHER BUTTONS Function PLAY STOP SCROLL PLAYMODE DISPLAY x/Z “PGM” REPEAT CLEAR TIME 4-7. TEST MODE DISPLAYS Each time the DISPLAY button is pressed, the display changes in the following order. When CPLAY and CREC are started, the display will forcibly be switched to the error rate display as the initial mode. 1.
  • Page 23 4-8. MEANINGS OF OTHER DISPLAYS Display Servo ON Tracking servo OFF REC z Recording mode ON CLV low speed mode L.SYNC ABCD adjustment completed Tracking offset cancel ON Tracking auto gain OK Focus auto gain OK High reflection SHUF CLV S MONO CLV LOCK 4-9.
  • Page 24: Electrical Adjustments

    5-1. PARTS REPLACEMENT AND ADJUSTMENT If malfunctions caused by optical pick-up such as sound skipping are suspected, follow the following check. Check before replacement 5-6-2. Laser Power Check 5-6-3. 5-6-4. Other faults are suspected. Check the threading mechanism, etc. SECTION 5 ELECTRICAL ADJUSTMENTS Start (See page 27)
  • Page 25 Adjustment flow Start Replace IC195 Replace OP or IO195 Replace IC101, IC195, or D101 Replace OP, IC190, or IC195 Replace OP, IC102, IC190, or IC195 Replace OP, IC101, IC151, or IC195 Replace OP Replace the spindle motor 5-6-4. Auto Check (See page 28) End adjustments After turning off and then on the power,...
  • Page 26: Servicing Notes

    5-2. PRECAUTIONS FOR CHECKING LASER DIODE EMISSION To check the emission of the laser diode during adjustments, never view directly from the top as this may lose your eye-sight. 5-3. PRECAUTIONS FOR USE OF OPTICAL PICK- UP (KMS-260B) As the laser diode in the optical pick-up is easily damaged by static electricity, solder the laser tap of the flexible board when using it.
  • Page 27 5-5. USING THE CONTINUOUSLY RECORDED DISC * This disc is used in focus bias adjustment and error rate check. The following describes how to create a continuous recording disc. 1. Insert a disc (blank disc) commercially available. 2. Rotate the AMS knob and display “CREC 1MODE” (C35). 3.
  • Page 28 5-6-4. Auto Check This test mode performs CREC and CPLAY automatically for mainly checking the characteristics of the optical pick-up. To perform this test mode, the laser power must first be checked. Perform Auto Check after the laser power check and Iop compare. Procedure 1.
  • Page 29 15. Observe the waveform of the oscilloscope, and check that the specified value is satisfied. Do not rotate the AMS knob. (Traverse Waveform) Specified value : Below 10% offset value IA – BI Offset value (%) = X 100 2 (A + B) 16.
  • Page 30 5-7. INITIAL SETTING OF ADJUSTMENT VALUE Note: Mode which sets the adjustment results recorded in the non-vola- tile memory to the initial setting value. However the results of the temperature compensation offset adjustment will not change to the initial setting value. If initial setting is performed, perform all adjustments again ex- cluding the temperature compensation offset adjustment.
  • Page 31 7. Then, rotate the AMS knob and display “LDPWR CHECK” (C13). 8. Press the @/1 button once and display “LD 0.9 mW $ Check that the reading of the laser power meter become 0.85 to 0.91 mW. 9. Press the @/1 button once more and display “LD 7.0 mW $ ”.
  • Page 32 10. Rotate the AMS knob until the waveform of the oscilloscope moves closer to the specified value. In this adjustment, waveform varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible. (Traverse Waveform) Specification A = B 11.
  • Page 33 5-14. ERROR RATE CHECK 5-14-1. CD Error Rate Check Checking Procedure : 1. Load a check disc (MD) TDYS-1. 2. Rotate the AMS knob and display “CPLAY1MODE” (C34). 3. Press the @/1 button twice and display “CPLAY1 MID”. 4. The display changes to “C = AD = 5.
  • Page 34 5-17. ADJUSTING POINTS AND CONNECTING POINTS [BD BOARD] (SIDE A) CN101 D101 [BD BOARD] (SIDE B) IC151 IC190 IC195 1 27 CN103 CN102 NOTE:It is useful to use the jig. for checking the waveform. (Refer to Servicing Note on page 6.) IC101 CN105 IC102...
  • Page 35: Diagrams

    SECTION 6 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING • Indication of transistor BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
  • Page 36: Block Diagrams - Bd Section

    MDS-PC3 6-1. BLOCK DIAGRAMS – BD SECTION – OVER WRITE HEAD DRIVE IC181, Q181, 182 HR901 OVER WRITE HEAD OPTICAL PICK-UP (KMS-260B/J1N) RF AMP B.P.F. TEMP ADFM B.P.F. ABCD DETECTOR COMMAND AUTOMATIC ILCC LD/PD POWER CONTROL SERIAL/PARALLEL Q121, 122 CONVERTER, DECODER LASER DIODE LASER ON...
  • Page 37: Main Section

    – MAIN SECTION – A/D, D/A CONVERTER IC500 HIGH-PASS FILTER, ADDT SDTO DIGITAL CONVERTER ATTENUATOR BLOCK (Page 36) AUDIO INTERFACE CONTROLLER DADT, BCK, DIGITAL LRCK DADT SDTI CONVERTER ATTENUATOR, BICK SOFT MUTE BLOCK (Page 36) LRCK LRCK SWDT, SCLK SWDT CDTI CONTROL SCLK...
  • Page 38: Printed Wiring Board - Bd Section

    MDS-PC3 6-2. PRINTED WIRING BOARD – BD SECTION – • Semiconductor Location Ref. No. Location D101 Q101 Q131 Q132 Q133 Q134 There are a few cases that the part isn’t mounted in model is printed on diagram. • Semiconductor Location Ref.
  • Page 39: Schematic Diagram - Bd Section (1/2)

    MDS-PC3 6-3. SCHEMATIC DIAGRAM – BD SECTION (1/2) – • See page 35 for Waveforms. • See page 46 for IC Block Diagrams. • See page 49 for IC Pin Functions. • See page 38 for Printed Wiring Board. PIN FUNCTION...
  • Page 40: Schematic Diagram - Bd Section (2/2)

    MDS-PC3 6-4. SCHEMATIC DIAGRAM – BD SECTION (2/2) – • See page 35 for Waveforms. • See page 46 for IC Block Diagrams. • See page 50 for IC Pin Functions. • See page 38 for Printed Wiring Board. PIN FUNCTION...
  • Page 41: Printed Wiring Board - Main Section

    6-5. PRINTED WIRING BOARD – MAIN SECTION – • MAIN and PANEL boards are lead free soldered (contains no lead). • Semiconductor Location Ref. No. Location Ref. No. Location D155 IC440 IC451 D156 D255 IC500 D256 IC501 D301 IC502 D400 IC503 D402 IC550...
  • Page 42: Schematic Diagram - Main Section (1/2)

    MDS-PC3 6-6. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) – • See page 35 for Waveforms. • See page 41 for Printed Wiring Board. • See page 48 for IC Block Diagrams. • See page 53 for IC Pin Functions. PIN FUNCTON...
  • Page 43: Schematic Diagram - Main Section (2/2)

    MDS-PC3 6-7. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) – • See page 35 for Waveforms. • See page 41 for Printed Wiring Board. • See page 47 for IC Block Diagrams.
  • Page 44: Printed Wiring Board - Panel Section

    MDS-PC3 6-8. PRINTED WIRING BOARD – PANEL SECTION – • MAIN and PANEL boards are lead free soldered (contains no lead). • Semiconductor Location Ref. No. Location D751 Q701 Q751 • Semiconductor Location Ref. No. Location IC781 There are a few cases that the part isn’t mounted in model is printed on diagram.
  • Page 45: Schematic Diagram - Panel Section

    MDS-PC3 6-9. SCHEMATIC DIAGRAM – PANEL SECTION – • See page 35 for Waveforms.
  • Page 46: Ic Block Diagrams

    6-10. IC BLOCK DIAGRAMS IC101 CXA2523AR (BD BOARD) 43 42 USROP – RFA1 RFA2 RFA3 – HLPT –1 – – –2 – OFST PTGR – – –2 – –1 – GRVA PBSW – – – – – ABCDA – – –...
  • Page 47 IC400 MAX1626ESA-TE2 (MAIN BOARD) 1.5V MINIMUM ON-TIME ERROR ONE-SHOT COMPARATOR TRIG – TRIG MINIMUM OFF-TIME ONE-SHOT SHDN CURRENT-SENSE COMPARATOR IC440 LB1830M-S-TE-L (MAIN BOARD) VREF VREF LOGIC PREDRIVER OUT2 OUT1 VS IC451 XC6351A120MR (MAIN BOARD) CHIP CCE/ ENABLE OSCILLATOR IC500 AK4524 (MAIN BOARD) –...
  • Page 48 IC420 M62016FP-E1 (MAIN BOARD) INTERRUPT SIGNAL – GENERATOR RESET SIGNAL – GENERATOR IC503 BH3541F-E2 (MAIN BOARD) LOUT BIAS BIAS MUTE ROUT MUTE IC800 P82B715TD.118 (MAIN BOARD) BUFFER BUFFER 1 RESET 180k 180k...
  • Page 49: Ic Pin Functions

    6-11. IC PIN FUNCTIONS • IC101 CXA2523AR RF Amplifier (BD BOARD) Pin No. Pin Name 4 to 9 A to F APCREF TEMPI TEMPR SWDT SCLK XLAT XSTBY F0CNT VREF EQADJ 3TADJ WBLADJ CSLED ADFM ADIN ADAGC ADFG ABCD BOTM PEAK RFAGC AGCI...
  • Page 50 • IC151 CXD2662R Digital Signal Processor, Digital Servo Signal Processor (BD BOARD) Pin No. Pin Name MNT0 (FOK) MNT1 (SHCK) MNT2 (XBUSY) MNT3 (SLOC) SWDT SCLK XLAT SRDT O (3) SENS O (3) XRST SQSY DQSY RECP XINT OSCI OSCO XTSL DIN0 DIN1...
  • Page 51 Pin No. Pin Name MVCI ASYO ASYI AVDD BIAS AVSS FILI FILO O (A) CLTV PEAK BOTM ABCD AUX1 ADIO O (A) AVDD ADRT ADRB AVSS DCHG ADFG F0CNT XLRF CKRF DTRF APCREF TEST0 TRDR TFDR DVDD FFDR FRDR SRDR SFDR SPRD SPFD...
  • Page 52 • IC300 M30805SGP (MAIN BOARD) Pin No. Pin Name DATA(FL) CLK(FL) A1-IN SIRCS 5, 6 MUTE A/D,D/A RESET A/D, D/A LATCH LD-LOW LDIN LDOUT BYTE CNVSS XIN-T XOUT-T RESET XOUT DQSY PDOWN SQSY K.B-CLK LDON LIMIT-IN A1 OUT XINIT BEEP LRCK1 WR PWR IIC CLK...
  • Page 53 Pin No. Pin Name SHCK (MNT1) EEP-WP BUSCLK CASH WE R/W REFLECT-SW PROTECT-SW 77 to 85 A17 to A9 86 to 89 MODEL SEL-1-4 94 to 100 A7 to A1 A0 LB 102 to 113 D15 to D4 KB.CLK-CTL IIC BUSY KB DATA REC-VOL-B REC-VOL-A...
  • Page 54: Exploded Views

    NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
  • Page 55: Mechanism Section-1 (Mdm-7A)

    7-2. MECHANISM SECTION-1 (MDM-7A) supplied Ref. No. Part No. Description * 301 4-996-267-01 BASE (BU-D) 4-231-319-01 SCREW (2X6) CZN, +B (P) TRI 4-227-007-01 GEAR (SB) 4-227-025-01 BELT (LOADING) 3-372-761-01 SCREW (M1.7), TAPPING 4-227-002-01 GEAR, PULLEY 4-226-999-01 LEVER (HEAD) X-4952-665-1 SPRING (SHT) ASSY, LEAF 4-228-923-01 LOCK (HOLDER) 4-229-533-02 SPRING (STOPPER), TORSION 4-231-118-01 SPRING (HOLDER), TENSION...
  • Page 56: Mechanism Section-2 (Mdm-7A)

    7-3. MECHANISM SECTION-2 (MDM-7A) S102 M103 Ref. No. Part No. Description A-4725-054-A BDBOARD, COMPLETE 4-231-319-01 SCREW (2X6) CZN, +B (P) TRI 3-372-761-01 SCREW (M1.7), TAPPING 4-226-993-01 RACK 4-227-014-01 SPRING (RACK), COMPRESSION 4-226-992-01 BASE, SL 1-678-514-11 FLEXIBLE BOARD 0 358 A-4672-541-A OPTICAL PICK-UP KMS-260B/J1N 4-988-560-01 SCREW (+P 1.7X6) 4-996-265-01 SHAFT, MAIN 4-226-989-01 CHASSIS...
  • Page 57: Electrical Parts List

    NOTE: Ref. No. Part No. Description • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one.
  • Page 58 Ref. No. Part No. Description IC171 8-759-096-87 IC TC7WU04FU(TE12R) IC181 8-759-481-17 IC MC74ACT08DTR2 IC190 8-759-460-72 IC BA033FP-E2 IC195 8-759-640-41 IC IC BR24C08F-E2 < JUMPER RESISTOR > JW201 1-216-295-11 SHORT JW202 1-216-295-11 SHORT JW203 1-216-295-11 SHORT JW903 1-216-295-11 SHORT JW904 1-216-295-11 SHORT <...
  • Page 59 Ref. No. Part No. Description < SWITCH > S101 1-762-596-21 SWITCH, PUSH (1 KEY) (LIMIT IN SW) S103 1-771-956-21 SWITCH, PUSH (1 KEY) (OUT SW) S104 1-771-955-21 SWITCH, PUSH (1 KEY) (PLAY SW) S105 1-771-955-21 SWITCH, PUSH (1 KEY) (REC SW) ************************************************************** A-4725-377-A MAIN BOARD, COMPLETE (US) *************************...
  • Page 60 MAIN Ref. No. Part No. Description C611 1-164-156-11 CERAMIC CHIP C613 1-162-970-11 CERAMIC CHIP C661 1-164-156-11 CERAMIC CHIP C662 1-104-665-11 ELECT C800 1-164-156-11 CERAMIC CHIP C804 1-164-156-11 CERAMIC CHIP C814 1-164-156-11 CERAMIC CHIP C851 1-216-864-11 METAL CHIP C852 1-216-864-11 METAL CHIP C853 1-216-864-11 METAL CHIP C854...
  • Page 61 Ref. No. Part No. Description R280 1-216-789-11 METAL CHIP R281 1-216-821-11 METAL CHIP R301 1-216-864-11 METAL CHIP R302 1-216-864-11 METAL CHIP R303 1-216-864-11 METAL CHIP R304 1-216-864-11 METAL CHIP R305 1-216-864-11 METAL CHIP R306 1-216-864-11 METAL CHIP R307 1-216-833-11 METAL CHIP R308 1-216-833-11 METAL CHIP R309...
  • Page 62 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W (2 KEY) (REFLECT/PROTECT SW) Sony Corporation Audio Entertainment Group Part No. Description ACCESSORIES & PACKING MATERIALS ******************************* A-4680-613-A OVERALL ASSY (PCLK-MN10) 1-469-089-11 FILTER, CLAMP (FERRITE CORE)(for USB CABLE)(CND,US) 1-476-295-11 REMOTE COMMANDER(RM-D52M)

Table of Contents