Page 1
10.4~21.5” IP69K Stainless P-Cap Display Model No. R10L100-SPT269 R15L100-SPC369 R19L100-SPM169 W22L100-SPA369 Quick Start Guide For more information on this and other Winmate products, please visit our website at: www.winmate.com Version 1.0 Document Part Number: 915211101031 Please read this instructions before operating the device and retain them for future reference.
Page 3
IP69K Stainless Display Quick Start Guide Preface FCC Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received ...
Page 4
Disclaimer Winmate Inc. reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for...
Page 5
IP69K Stainless Display Quick Start Guide Preface Customer Service We provide a service guide for any problem by the following steps: First, visit the website of our distributor to find the update information about the product. Second, contact with your distributor, sales representative, or our customer service center for technical support if you need additional assistance.
Page 6
IP69K Stainless Display Quick Start Guide Preface Advisory Conventions Four types of advisories are used throughout the user manual to provide helpful information or to alert you to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and Warnings. The following is an example of each type of advisory.
❶ INTRODUCTION Congratulations on purchasing Winmate® IP69K Stainless P-Cap Display. Winmate flat stainless steel P-Cap Display is designed for applications with high hygienic requirements. IP69K series is completely waterproof with IP69K level of protection allowing for easy cleaning and sterilization.
IP69K Stainless Display Quick Start Guide Introduction 1.2 Package Content Carefully remove the box and unpack your device. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately. Factory shipment list: Quick Start Guide R-series AD Board...
IP69K Stainless Display Quick Start Guide Introduction 1.3 Product Overview This section contains mechanical drawing of the Display. Notice that this is a simplified drawing and some components are not marked in detail. 1.3.1 Dimensions 10.4" Unit: mm Dimensions : 289 x 246 x 49.9 1.3.2 Dimensions 15"...
IP69K Stainless Display Quick Start Guide Introduction 1.4 Physical Buttons and LED Indicators Physical buttons and LED indicators located on the rear side of the Display. Physical Buttons Icon Button Description DOWN/ Press to decrease the volume or VOLUME volume down when without OSD DOWN menu.
IP69K Stainless Display Quick Start Guide Introduction 1.5 Connectors IP69K Stainless P-Cap Display has M25 type connectors with protection cap and air venting valve. - 12 -...
IP69K Stainless Display Quick Start Guide Getting Started ❷ GETTING STARTED 2.1 Turning On and Off the Device Follow the following steps to turn on your device: 1. Connect the AC adapter to the DC-in jack connector located on the back side of the Display.
IP69K Stainless Display Quick Start Guide Installation ❸ INSTALLATION 3.1 Wiring Requirements The following common safety precautions should be observed before installing any electronic device: Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point.
IP69K Stainless Display Quick Start Guide Installation 3.2 Connector Pin Assignments This Display is equipped with four M25 type connectors which are waterproof. Use only the cables that are included in the package. The pin assignments of the cables are as follows. 3.2.1 Power Cable The IP69K Stainless P-Cap Display has M25 type connectors.
IP69K Stainless Display Quick Start Guide Installation 3.2.2 USB Cable (For Touch) The Flat Stainless P-Cap Display has M25 type USB connector for touch. Use USB cable to connect touch. 3.2.3 VGA Cable The Flat Stainless P-Cap Display has M25 type VGA connector. Use VGA cable to connect the display to other external devices.
IP69K Stainless Display Quick Start Guide Installation 3.2.4 DVI Cable (Optional) The Flat Stainless P-Cap Display has optional waterproof DVI connector. Use DVI cable to connect the Display to other external device. - 17 -...
3.6.1 VESA Mounting The Display has VESA mount holes on the rear side. Follow instructions below to mount the unit with VESA Mount bracket (not supplied by Winmate). Size VESA Plate...
Installation 3.6.2 Yoke Mounting Yoke Mount solution allows installing the Display with the bracket (not supplied by Winmate). Mounting instruction: 1. Place the Display on the bracket stand, aiming screw holes for each other. 2. Secure screws to fix the device upon the bracket stand.
IP69K Stainless Display Quick Start Guide Appendix APPENDIX Appendix A: Cleaning the Monitor NOTE: The IP69K Stainless withstands regular intense cleaning Display and could hold up against steam and high-pressure water. The devices are able to sustain water temperatures up to 80°C and a water jets.
Appendix Appendix B: Available Input Signals For information about available input signals, please refer to R-Series AD Board Manual included in the package. You can also download R - Series AD Board Manual from Winmate Download Center. - 22 -...
Need help?
Do you have a question about the R10L100-SPT269 and is the answer not in the manual?
Questions and answers