Fitting The Replacement Base Pcb; Cables And Wiring - Honeywell Notifier ID3000 Series Installation & Commissioning Manual

8
8
8
8
8
8
L
1 1
1 1
1 1
1 1
1 1
1
+ 1 - + 1 - + 2 - + 2 - + 3 - + 3 - + 4 - + 4 - + + - -
INPUTS 1 & 2 INPUTS 1 & 2
OUTPUTS 1 & 2 OUTPUTS 3 & 4
viii. viii. vii
+ - + -
LOOP 1
iii.
ix.
SK2 SK2
2 2 14 14 2 2 14 14
13 13 1 1
1 1 1 13 13
x.
3 + 4 3 + 4
SK4
2 16
15
1
xiii.
xiv.
SK11
1
5
2
1
RS232
SK9
9 6
Base PCB PN: 124-361
ID3000 Series Installation & Commissioning Manual

5.7.1 Fitting the Replacement Base PCB

10 Taking suitable anti-static precautions and with the
11 Using a No.1 Posidriv screwdriver starting with the top
Note: Set the link settings on the replacement PCB to
12 Re-fit all PCBs removed in steps 5, 6 and 7 above.
13 With all items replaced and wiring and cabling
5.7.2 Cables & Wiring
Disconnect/reconnect the following from the Base PCB:
2
2 1
+ + - -
+ + - - + + - -
AUX AUX
vi. vi.
1 2
+ + - - + - + - + - + -
FIRE
FAULT
LOOP 2
iii. iv. iv.
SK3
2
xi. xii.
SK6 SK7
5 + 6 5 + 6 7 + 8 7 + 8
2 2
16
15 1
1
i.
BASE PCB
124-361
9
10
replacement Base PCB orientated correctly, offer it to
the main chassis PCB enclosure. With the locating holes
on the PCB lined up with the hank-bush studs, guide
the Base PCB into position.
left corner, gently fix each of the seven (7) M3 x 10 SEM
screws from step 8 screw in turn and then secure.
DO NOT over-tighten.
those noted in step 8.
Re-fit the main chassis in the back box - using the
reverse of the main chassis removal procedure.
re-terminated, reconnect
mains power first and then the batteries to the panel.
i. Power sockets, SK8 and SK12 (from PSU
or DTP).
ii. Data socket, SK1 (from Processor PCB).
iii. Loop Cabling connectors, TB6 and TB7
(Loops 1 & 2).
iv. Fault and Fire Relay sockets, TB8 and TB9.
v. Cover Off connector, SK10 (not used).
vi. Auxiliary sockets, TB4 and TB5.
ii.
vii. Input socket, TB3 (Input 1 only supported
32
for VdS configuration).
30
viii. Output Sockets, TB1 and TB2.
ix. Comms sockets (A and B), SK2 and SK3
25
(from Isolated RS485 Interface PCB or
Printer RS232 Interface PCB, if fitted).
20
x. Loop Cabling connector, SK4 (from Loops
3 & 4 Interface PCB, if applicable).
15
xi. Loop Cabling connector, SK6 (from Loops
5 & 6 Interface PCB, if applicable).
10 xii. Loop Cabling connector, SK7 (from Loops
7 & 8 Interface PCB, if applicable).
xiii. RS232
5
Connector, SK11.
1
xiv. Zone Expansion Socket, SK9 (refer to
Section 5.5).
A C
SK8
i.
1 2
The selection of sounders or volt-free
16
15
contacts, and normally-open or
9 10
normally-closed, is described in
SK12
1 2
Section 7.7. For volt-free contacts
(outputs 3 & 4 only) the '-ve' terminal
3 4
is common.
33
earthing cables,
Off-line Configuration PC
997-274-000-6, Issue 6
September 2009