Related Manuals for MotoSAT EXECUTIVE / MiniDome OSD
Summary of Contents for MotoSAT EXECUTIVE / MiniDome OSD
- Page 1 EXECUTIVE / MiniDome USERS MANUAL USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD MotoSAT Corporation Created April 22, 2003 1-800-247-7486...
-
Page 2: System Features
CONGRATULATIONS! …on your purchase of your Satellite RV-TV system from MotoSAT. We are excited here at MotoSAT to introduce to you the cutting edge of Satellite technology. The features of the new dish positioning system will have you feeling in total control. SYSTEM FEATURES •... -
Page 3: Table Of Contents
TABLE OF CONTENTS Do You Have The Right Receiver?………………………….…. MotoSAT Shipped Components………………………………... The MotoSAT Positioner………………………………………… How to Reset Memory …………………………………… Functions of your MotoSAT System………………………….. Using your MotoSAT System…………………………………... THE MAIN MENU SCREEN……………………………………… Changing receiver output between channel 3 and 4 THE SETUP SCREEN…………………………………………... -
Page 4: Do You Have The Right Receiver
DirecTV – Works with: RCA Models - 420 Series (420, 440 480) and 430 Series (430, 450, 485). Sony SAT-A65, B65, A65-A, B65-A Hughes GCEBO, GCEBOA, GAEBO, GABEOA, Remotes on these models are EXTREMELY sensitive and are not recommended. -
Page 5: The Motosat Positioner
THE MotoSAT Executive OSD Positioner NOTE – You will need to place the MotoSAT Positioner (OSD) inside the same cabinet that your receiver is located. Wireless communication is happening between the MotoSAT Positioner and the TV Receiver that is not possible when units are separated (see Figure 1). LIGHTS &... -
Page 6: Functions Of Your Motosat System
FUNCTIONS OF YOUR MotoSAT SYSTEM AUTOMATIC SEARCH AND LOCK ON THE CORRECT SATELLITE MotoSAT gives you on-screen control of your satellite system. No matter where you find yourself in the United States, your system is smart enough to make sure you have connected to the satellite of your choice. - Page 7 CHANGING REMOTE CONTROL TYPE Your installer normally sets this function. However, you may have purchased a new Satellite Receiver, in which case, you will need to tell the MotoSAT positioner which kind of Satellite Receiver you are now using. Holding the front panel button in for 30 seconds can also do this function. If the power button is held in for 30 seconds it will also erase satellites stored in memory.
-
Page 8: Using Your Motosat System
USING YOUR MotoSAT SYSTEM There are four basic operations that you will use any time you want to watch television. 1. TURNING ON THE SYSTEM 2. FINDING SATELLITE 3. STOWING THE DISH 4. TURNING OFF THE SYSTEM Of course there are many other functions you may perform, but for now, let’s focus on getting the TV working. TURNING ON THE SYSTEM Two things need to be turned ON in order for your system to function. -
Page 9: The Main Menu Screen
THE MAIN MENU SCREEN If you do not see the MotoSAT Screen appear when you power up the system, please go to TROUBLESHOOTING at the end of the manual. FIND SATELLITE - While the Main Menu screen is on your TV screen, use your Receiver’s Remote to navigate this screen. - Page 10 Please choose the city you are in or closest to. Once you do that, the below menu will appear and the dish will start to move automatically. Note: Pressing the #1 button at this time will open up the receivers Signal Strength Menu and allow you to monitor the satellite finding and peaking process.
-
Page 11: Setup Screen
The Main Menu allows you to perform some basic operations. It also shows which Satellite TV service you are subscribed and whether or not your dish has ever tested. SETUP SCREEN Choosing INFORMATION, DIAGNOSTICS, OPTIONS, and SATELLITE SETUP will take you to those screens. TEST DISH - Selecting Test Dish will put the dish through a full motor and limit test. -
Page 12: The Information Screen
The information screen shows manufacturing information about your system. When it was built, and who it was built by… which of course is MotoSAT. Also included is MotoSAT’s address, phone numbers and web site as well as Hardware and Software Revision information. DIAGNOSTICS SCREEN This screen is used by MotoSAT technical support to help trouble shoot your system when things go wrong. -
Page 13: Tone Setting
The tone settings for RCA, Dish Network, and Bell Express Vu receivers should be 7. b. The tone settings for Sony and Hughes receivers it should be set to 15. Why would you need to adjust the Tone Settings? If your system stops or peaks on the proper satellite, but continues to search or, if your system stops or peaks and stays on an improper satellite you will need to adjust TONE SETTING. - Page 14 Power Control Cable Out to TV Ignition Stow SATELLITE SETUP SCREEN The great thing about your satellite system is that you can switch from one satellite to another at will to take advantage of different programming on different satellites. Note: some receivers may not load their Guide properly on alternate satellites.
-
Page 15: Wiring Diagram
Satellite Options To get to the Satellite Options Screen press the Select or OK button on a highlighted satellite on the satellite setup screen. Note: You can not change the options on the satellite that is considered the default. If you select the default satellite, nothing will happen. - Page 16 MotoSAT WIRING DIAGRAM...
-
Page 17: Rear View
MotoSAT Positioner (Rear view) Pins 1 2 3* 1 2 3 4 5 6 7 8 9 Power Control Cable Out to TV Ignition * *Ignition = When 12 to 24 VDC is applied to pin 3 the dish will return to stowed position automatically. **Pin 9 –... -
Page 18: Dry-Camping (Power Saving)
Dry-Camping (Energy Conservation Wiring Option) Output DRY-CAMPING - This Dry Camping connection allows you to conserver power by turning off the MotoSAT positioner after you’ve found satellite. This Cable must be connected for this option to work. When ON Satellite, simply turn OFF your OSD Positioner. -
Page 19: Troubleshooting
TROUBLESHOOTING THE MOTOSAT SCREEN DOES NOT APPEAR If you can’t get a MotoSAT menu to appear on your television, make sure it isn’t something simple like cables not being connect properly or that the power is OFF on your Television, TV Receiver, or MotoSAT positioner. - Page 20 Proper Placement of Equipment Receiver has to be placed just back of clear plastic front. If placed forward of this location it will cause error “Please Wait” because the Positioner cannot communicate with the receiver. Approximate set back distance is 1/4” FIGURE 1...
- Page 21 “O” Ring Style Connectors O-Ring style of F-Connectors (for Coax Cable) Use of Coax connectors shown below will void warranty and can cause equipment intermittent problems. is not recommended nor authorized to be used on any MotoSAT product. If you use O-Ring style connectors, the O-Rings must be removed before being allowed to be used in...
- Page 22 MotoSAT Bulletin 010501 A/B Switches Product effected: All MotoSAT products and all satellite systems in general. Problem: a. Insertion of A/B switch into satellite signal cable going to the roof mounted antenna can cause selective dropping of channel frequencies. b. Loss of certain channels can result. (Usually, but not limited to, Network Feeds on DTV).
- Page 23 Updating of Operating Software in the OSD Positioner Your OSD Positioner contains software which may be reloaded (updated) by the use of a computer and a 9 pin serial cable. The procedure for updating your software to the latest version is as follows: 1.
- Page 24 MORE INFORMATION… Please visit www.motosat.com for the latest information regarding your MotoSAT products or e-mail info@motosat.com for additional information. CONTACTING MOTOSAT… MotoSAT Technical Assistance can be reached at 800-247-7486. Our hours of operation are 9AM to 5PM Monday through Friday Mountain Time. OUR ADDRESS IS …...