Table of Contents
Advertisement
Quick Links
AWM
ALL-WEAThER MoNIToR SERIES II: L, R, V AND VR
AWM SerieS ii: r, V, Vr
AWM SerieS ii: L
USER MANUAL
8.4" - 10.4" - 12.1" - 15.0" TFT ruggeD LCD DiSpLAyS
DIGITAL SYSTEMS ENGINEERING, INC. (DSE)
17491 NOrTH 93rD STreeT | SCOTTSDALe, AZ 85255
DSE SERVICE CENTER:
480-515-1110
SERVICE@DIGITALSYS.COM
|
WWW.DIGITALSYS.COM
© 2017 by DigiTAL SySTeMS eNgiNeeriNg. ALL rigHTS reSerVeD.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DIGITAL SYSTEMS ENGINEERING AWM Series
Summary of Contents for DIGITAL SYSTEMS ENGINEERING AWM Series
- Page 1 USER MANUAL 8.4" - 10.4" - 12.1" - 15.0” TFT ruggeD LCD DiSpLAyS DIGITAL SYSTEMS ENGINEERING, INC. (DSE) 17491 NOrTH 93rD STreeT | SCOTTSDALe, AZ 85255 DSE SERVICE CENTER: 480-515-1110 SERVICE@DIGITALSYS.COM WWW.DIGITALSYS.COM © 2017 by DigiTAL SySTeMS eNgiNeeriNg. ALL rigHTS reSerVeD.
- Page 2 Are NOT eNDOrSeMeNTS. COpYRIGhT THiS DOCuMeNT CONTAiNS prOprieTAry iNFOrMATiON prOTeCTeD by COpyrigHT. ALL rigHTS Are reSerVeD. NO pArT OF THiS MANuAL, iN WHOLe Or pArT, MAy be reprODuCeD by ANy MeANS, iN ANy FOrM, WiTHOuT priOr WriTTeN perMiSSiON OF DigiTAL SySTeMS eNgiNeeriNg.
- Page 3 ALL-WEAThER MoNIToR SERIES II: L, R, V AND VR AWM SerieS ii: r, V, Vr AWM SerieS ii: L USER MANUAL 8.4" - 10.4" - 12.1" - 15.0” TFT ruggeD LCD DiSpLAyS © 2017 by DigiTAL SySTeMS eNgiNeeriNg. ALL rigHTS reSerVeD. UM-AWM SERIES II (B) 4/17...
-
Page 4: Table Of Contents
On-Screen Display Menus ............. 20 Optional NViS ................. 24 Optional internal Heater, uSb pass-Through Connector ....25 Optional Touch Screen Display ............26 Appendix A - Mechanical Drawings ..........27 Appendix b - Troubleshooting ............27 UM-AWM SERIES II (B) 4/17... -
Page 5: Introduction
Analog resistive Touch Screen (available with r and Vr). Other options include Night Vision (NViS) compatibility, a pass-through uSb port and an inter- AWM SerieS ii: r, V, Vr nal heater, necessary when working in critically low temperatures, down to -40ºC (-40ºF). -
Page 6: General Safety Precautions
GENERAL SAfETY SAfETY ICoNS Safety icons are inserted throughout the AWM Series ii user Manual to draw attention to specific user Caution and Warning instructions. WARNING! ShOCk hAzARDS This icon warns user of a potential risk of electrical shock. CAuTION! INSTRuCTIONAL This icon is intended to tell the user of important operating and/or maintenance instructions. -
Page 7: Electrical Safety Precautions
Display should need to be shipped to the DSe Service Center, the original packing material or similar should be used to ensure safety of Display in shipping. repack Display as it was originally received. protect the Display screen. UM-AWM SERIES II (B) 4/17... -
Page 8: Product Care And Maintenance
• Do not use paper products; they may scratch the screen, and • Do not directly apply cleaning solutions to screen. uSER TIp In marine or similar environments, an added benefit of a vinegar-based cleaner is its effectiveness in dissolving mineral and salt deposits. UM-AWM SERIES II (B) 4/17... -
Page 9: System Set-Up
• r and Vr: System input Cable • Mounting System and Hardware • bNC Cables are provided by the end-user • Touch Screen Cable if optional Touch Screen is ordered, and • uSb Cable if optional uSb pass-through is ordered. UM-AWM SERIES II (B) 4/17... -
Page 10: Installation
T-knob with a packet of three (3) M4 x 10 counter-sunk stainless screws for mounting. (Figures 1 - 3) Mounting Holes Figure 1 Ball and Panel Socket Mount Only Mount Only Figure 2 Figure 3 UM-AWM SERIES II (B) 4/17... -
Page 11: Pressure Equalizer Valve
There is a pressure equalizer Valve on the chassis. (Figure 5) in the final installation, do not block or constrain this valve. CAuTION! enclosure is aluminum; do not over tighten screws or strip screw holes. Figure 5 Do not block or constrain the pressure equalizer Valve. UM-AWM SERIES II (B) 4/17... -
Page 12: Display Connectors
+5V pRE hEAT LED bEEpER Cpu-hTR uSbD1- pWR VIN GND uSbD+ pWR VIN GND NO CONNECT pWR +VIN GROuND pWR +VIN p-MuSb-b151-05 AMphENOL # 836149012 MOLEX # 834219014 (MOLEX) MATE # Table 2 Table 1 UM-AWM SERIES II (B) 4/17... -
Page 13: Series R
Negative lead is not marked (Figure 9) Figure 9 • Connect flying leads to corresponding polarity on DC voltage source, primary terminal. WARNING! pOWER SOuRCE pOLARITY Verify polarity of power source posts prior to connecting cable’s flying leads. UM-AWM SERIES II (B) 4/17... -
Page 14: Series V
• end-user supplies bNC coaxial video cable • bNC receptacle on Display is ip67 sealed • Line up with bNC connector, #2 in Figure 11, and • plug together, adding a ¼ turn to connect. UM-AWM SERIES II (B) 4/17... - Page 15 “+” label • Negative lead is not marked (Figure 12) • Connect flying leads to corresponding polarity on DC Figure 12 voltage source, primary terminal. CAuTION! Use care when inserting or removing connector. Do not force mating. This section is intentionally left blank. UM-AWM SERIES II (B) 4/17...
-
Page 16: Series Vr
Display until cable is free • positive flying lead marked with “+” label • Negative lead is not marked (Figure 15) • Connect flying leads to corresponding polarity on DC voltage source, primary terminal. Figure 15 UM-AWM SERIES II (B) 4/17... -
Page 17: Optional Ac Power Adapter
To disconnect, pull outside ring on connector away from Display until free. Note: Optional AC Power Adapter is not an off-the-shelf item. It is equipped with a specific connector for integration with the AWM Displays. Figure 16 UM-AWM SERIES II (B) 4/17... -
Page 18: Operator Controls
CoNTRoLS - SERIES L (LVDS) On right hand of the AWM Series L Display bezel are two (2) Operator Control buttons. (Figure 17) PoWER oN/off Note: Display defaults to an AUTO-ON state when Power On/Off (I/O) power is applied. Button Large sun •... - Page 19 CoNTRoLS - SERIES R, V, VR On right hand of the AWM Series r, V and Vr Display bezel are seven (7) Operator Control buttons. (Figure 18) PoWER oN/off (I/o) bUTToN PoWER oN/off bRIGhTNESS CoNTRoL ToGGLE Note: Display defaults to an AUTO-OFF state when (LARGE SUN, SMALL SUN) power is applied.
-
Page 20: On-Screen Display Menus
DISPLAY MENU For the AWM Series R, V and VR, the On-Screen Display (OSD) User Interface is where Display adjustments are made. With its user-friendly graphical interface, the OSD Menu provides access to fine-tuning the Display according to the user’s preferences. Note: There is no OSD menu in AWM Series L. - Page 21 Select for first input Signal. Select exit button to save. C VIDEo 2 Select for second input Signal. Select exit button to save. C VIDEo 3 Select for third input Signal. Select exit button to save. UM-AWM SERIES II (B) 4/17...
- Page 22 Select Saturation to adjust intensity or vividness (saturation) of color. Factory default is 50 within range of 0 - 100. use the up (increase) or DOWN (decrease) button to adjust in indi- vidual increments. Select exit button to save. UM-AWM SERIES II (B) 4/17...
- Page 23 The user may view a second video source in addition to the default signal source by utilizing the picture-in-picture (pip) feature. The pip Menu has two selections: pip Source; pip Mode. PIP SoURCE pip Source allows user to select the Composite Video Source (C 1 - 3) for the pip. UM-AWM SERIES II (B) 4/17...
-
Page 24: Optional Nvis
NViS green or NViS red in the OSD menu. Once saved in the OSD, the up / DOWN ArrOW buttons will toggle between that selection (green or red) and Day Mode; both NViS colors are not available at the same time. UM-AWM SERIES II (B) 4/17... -
Page 25: Optional Internal Heater, Usb Pass-Through Connector
#3, Figure 14, and • uSb pass-through Connector on other end is a standard A-type uSb port socket; it is not a sealed (watertight) connector. uSb pORT The USB port socket on the cable is not sealed. UM-AWM SERIES II (B) 4/17... -
Page 26: Optional Touch Screen Display
(O/S), do not install Touch Screen Controller Driver until O/S is installed and system’s video display settings have been verified. Touch Screen Controller Driver uses system’s O/S display driver settings to accurately configure T/S Con- troller Driver files. UM-AWM SERIES II (B) 4/17... -
Page 27: Appendix A - Mechanical Drawings
OSD. These may be set too low. System may have gone into power management stand-by. press any key on the keyboard, move the mouse or cursor, or if there is a Touch Screen, touch to wake the system. UM-AWM SERIES II (B) 4/17... - Page 28 Check for proper video cable installation, or re- place suspected faulty cable. Verify system video display is set at 800 x 600 pixels (1024 x 768 pixels) and at a 60 - 75Hz re- fresh rate. UM-AWM SERIES II (B) 4/17...
- Page 29 Uninstall the driver using “TSUN10.exe”. If a correctly previous T/S Controller Driver was installed, all footprints must be removed. Go to the T/S manufacturer’s or contact the manufacturer for instructions to uninstall driver. Reinstall the TSHARC Driver software. UM-AWM SERIES II (B) 4/17...
- Page 30 NoTES UM-AWM SERIES II (B) 4/17...
- Page 31 NoTES UM-AWM SERIES II (B) 4/17...
- Page 32 DIGITAL SYSTEMS ENGINEERING, INC. (DSE) 17491 NOrTH 93rD STreeT | SCOTTSDALe, AZ 85255 DSE SERVICE CENTER: 480-515-1110 SERVICE@DIGITALSYS.COM WWW.DIGITALSYS.COM © 2017 by DigiTAL SySTeMS eNgiNeeriNg. ALL rigHTS reSerVeD. UM-AWM SERIES II (B) 4/17...
Need help?
Do you have a question about the AWM Series and is the answer not in the manual?
Questions and answers