Download  Print this page

Advertisement

BiPAP autoSV Advanced System One
PROVIDER GUIDE
IMPORTANT! Remove this guide before giving the device to the patient. Only medical professionals should adjust pressure settings.
This guide must be used with the User Manual when used by a medical professional. Read and understand the User Manual,
the Provider Guide, and all accessory manuals before setting up the device. This guide provides you with instructions on how
to access and navigate the provider screens used to modify device settings.
Note: The screens shown throughout this guide are examples only. Actual screens may vary slightly.
Accessing the Provider Mode Screens
Accessing provider mode unlocks settings that cannot be modified by the user. To access provider mode:
1. Supply Power to the device. First, plug the socket end of the AC power cord into the power supply. Then plug the
pronged end of the AC power cord into an electrical outlet that is not controlled by a wall switch. Finally, plug the power
supply cord's connector into the power inlet on the back of the device.
2. Once the device is powered, the Main Menu appears, shown below. Turn the wheel to toggle between the four options
and highlight "Setup".
Therapy
Info
Main Menu
Note: "Bi-Flex" shown above may also display a blank screen or "Rise Time" depending on your settings.
3. Once "Setup" is highlighted, press and hold both the Control Wheel and the Ramp Button
5 seconds.
4. You will hear a quick double beep and the Provider Menu will appear, shown below. You are now in provider mode.
EXIT
Info
Provider Menu
Bi-Flex
Setup
Reminder
Setup
on the device for at least
- 1 -

Advertisement

Table of Contents

   Also See for Philips Respironics BiPAP autoSV Advanced System One

   Summary of Contents for Philips Respironics BiPAP autoSV Advanced System One

  • Page 1 BiPAP autoSV Advanced System One PROVIDER GUIDE IMPORTANT! Remove this guide before giving the device to the patient. Only medical professionals should adjust pressure settings. This guide must be used with the User Manual when used by a medical professional. Read and understand the User Manual, the Provider Guide, and all accessory manuals before setting up the device.
  • Page 2: Setup Screen

    Navigating the Provider Mode Screens To navigate these display screens: Turn the wheel to toggle between options and settings on the screen. Press the wheel to choose an option or setting that is highlighted. If you choose “Back” on any screen, it will take you back to the previous screen. Note: Choosing “EXIT”...
  • Page 3 • Max pressure - This screen displays the current Maximum pressure setting. You can adjust the setting from 4 to 25 cm O in 0.5 increments. • EPAP min - This screen allows you to modify the Minimum EPAP setting. The setting specified here will be the minimum level of pressure applied during the expiratory breath phase.
  • Page 4 • Humidifier - This setting allows you to choose the desired humidity setting: 0, 1, 2, 3, 4 or 5. If the System One humidity control has been disabled, the classic style of basic temperature controlled heated humidification will be used and the display will show: 0, C1, C2, C3, C4 or C5 for these settings.
  • Page 5: Info Screen

    Info Screen From the Provider screen, highlight “Info” and press the wheel. The following Info screen will appear. Back Oximetry Device Settings Monitor Params Phone-in Compliance VIC Therapy hours Blower hours Days > 4 Large leak Periodic breathing 90% EPAP Average PS Reset data Machine hours...
  • Page 6 • Therapy hours - The device is capable of recognizing the difference between the time the patient is actually receiving therapy and the time when the blower is simply running. This screen displays the average amount of time the patient is actually receiving therapy on the device over a 7 day and 30 day time frame (provided the device has at least 7 or 30 days of data respectively).
  • Page 7 Bi-Flex Comfort Feature The device consists of a special comfort feature called Bi-Flex. When Flex type is set to Bi-Flex, the Bi-Flex attribute adjusts therapy by inserting a small IPAP amount of pressure relief during the latter stages of inspiration and during active exhalation (the beginning part of exhalation).
  • Page 8 Digital Auto-Trak Sensitivity An important characteristic of the device is its ability to recognize and compensate for unintentional leaks in the system and to automatically adjust its trigger and cycle algorithms to maintain optimum performance in the presence of leaks. This feature is known as Digital Auto-Trak Sensitivity.
  • Page 9 Spontaneous Expiratory Threshold (IPAP to EPAP) The method used to cycle off IPAP during spontaneous breathing is called Spontaneous Expiratory Threshold (SET). The SET rises in proportion to the inspiratory flow rate on each breath. When the SET and the actual patient flow value are equal, the unit cycles to EPAP. Maximum IPAP Time (IPAP to EPAP) A maximum IPAP time of 3.0 seconds acts as a safety mechanism to limit the time spent at the IPAP level during spontaneous breathing.
  • Page 10 Cleaning for Multiple Patient Use (Home or Hospital) WARNING: If you are using the device for multiple patients, a new bacteria filter shall be used each time the device is used on a different person. If you are using the device on multiple users, complete the following steps to clean the device before each new user. 1.
  • Page 11 Verifying the Alarms Use the test orifice from the “Verifying the Pressure” instructions and the patient’s prescription for the following tests. Patient Disconnect Alarm Test Note: The Patient Disconnect Alarm relies on a fixed relationship between the patient pressure settings and the open circuit flow of the patient circuit.
  • Page 12: Adding Supplemental Oxygen, Specifications

    Adding Supplemental Oxygen Please note the oxygen warnings listed in the User Manual when using supplemental oxygen. The delivered oxygen concentration varies with changes in flow in the circuit. The following may have an impact on oxygen concentration: • Pressure settings •...
  • Page 13 Updating Software Using the SD Card You can update the device software using the SD Card. The software update must be done when the therapy is off. 1. Insert an SD Card with the new software version into the device. The following screen appears on the display. Do you wish to upgrade from version 1.0 to version 1.1?
  • Page 14: Emc Information

    EMC Information Guidance and Manufacturer’s Declaration - Electromagnetic Emissions – This device is intended for use in the electromagnetic environment specified below. The user of this device should make sure it is used in such an environment. missions omplianCE lECTromagnETiC nvironmEnT uidanCE RF emissions...
  • Page 15 Guidance and Manufacturer’s Declaration - Electromagnetic Immunity – This device is intended for use in the electromagnetic environment specified below. The user of this device should make sure it is used in such an environment. iEC 60601 T mmuniTy EvEl omplianCE EvEl lECTromagnETiC...
  • Page 16 1071074 1070901 R00 JR 12/20/2010 EN-DOM - 16 -...

Comments to this Manuals

Symbols: 0
Latest comments: